Hyrig Boiler Feed Booster Pump BB2 – API 610 Centrifugal Pump for Medium Pressure Boiler Feed

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Hyrig API 610 BB2 boiler feed booster pump is designed for medium pressure boiler feed and booster duties. Handles deaerated water up to 200°C. Double suction impeller ensures low NPSH and axial balance. Flow to 3000 m³/h, head to 150 m. Centerline mounted, API 682 seals. Reliable feed to high pressure pumps or medium boilers. Contact info@hyrig.com.

Conatct For Details
DetailReview(0)Additional

Hyrig’s Boiler Feed Booster Pump BB2 is a heavy duty centrifugal pump manufactured per API 610 (ISO 13709), BB2 type. This horizontally mounted, radially split, double suction (or single suction for smaller sizes), two-bearing supported pump is specifically engineered for medium pressure boiler feed booster service – typically raising the pressure of deaerated water before entering a high pressure multistage pump, or directly supplying medium pressure industrial boilers.

Typical Boiler Feed Booster Service Configurations

ConfigurationTypical PressureCommon Pump Type
Low pressure circulation (heating)≤10 barOH2 or BB2
Booster to high pressure main feed pump10–30 bar outletBB2 (ideal)
Direct feed to medium pressure boiler (30–60 bar)30–60 barBB2 (single or two stage)
High pressure main feed (>80 bar)>80 barBB3/BB4/BB5 – not BB2

The Hyrig BB2 is not designed for high pressure main boiler feed service (>80 bar). For those applications, please refer to our API 610 BB3/BB5 multistage pumps.

Why choose BB2 for boiler feed booster duty?
Booster pumps are typically located downstream of the deaerator, where available NPSH is relatively low (3–6 m). The BB2 configuration offers:

  • Double suction impeller – significantly reduces NPSH requirement; inherent axial thrust balance

  • Centerline mounting – handles warm water temperature (up to 200°C) without alignment shift

  • Two bearing support – rigid rotor dynamics for continuous operation

  • Radially split casing – easy maintenance without disturbing piping

Typical Operating Parameters

ParameterRange
Flow rate30 – 3,500 m³/h (130 – 15,400 USgpm)
Head (per stage)30 – 150 m (100 – 490 ft) – typical booster range
Total head (two stage BB2)Up to 300 m – for higher pressure direct boiler feed
TemperatureUp to 200°C (392°F) – deaerated water
Inlet pressure2 – 10 bar (29 – 145 psi) – from deaerator or LP drum
Discharge pressureUp to 60 bar (870 psi) – for medium pressure boilers
Speed1480 / 2980 rpm (50/60 Hz)

Key Applications for Boiler Feed Booster Pump BB2

  • Booster to high pressure multistage pump – raises pressure before main feed pump to prevent cavitation

  • Medium pressure industrial boiler feed – directly feeding boilers up to 60 bar

  • Heating circulation loop – pressurized hot water circulation (district heating)

  • Waste heat recovery boiler feed – once through steam generator (OTSG) booster

  • Desalination plant brine heater feed

Design Features for Reliable Boiler Feed Booster Service

Hydraulic Design

  • Double suction first stage (for BB2 with two stages) – lowest NPSH, ideal for deaerator outlet

  • Single suction option – for smaller flows (<200 m³/h) where NPSH is adequate

  • Low suction specific speed (Nss) design – ensures stable operation down to minimum flow

Materials (clean, deaerated water)

  • Casing: Carbon steel ASTM A216 WCB (standard) or stainless steel for high purity

  • Impeller: Carbon steel or 12% chrome (CA6NM) for erosion resistance

  • Shaft sleeves: 17-4 PH or similar hard material

  • Wear rings: Standard 12% chrome; optional hard coating

Sealing System (API 682)

  • Seal chamber designed per API 682 for water service

  • Standard: Single cartridge mechanical seal with API Plan 11 (recirculation from casing)

  • Optional: Plan 23 (jacketed seal cooler) for higher temperature (>150°C)

  • Plan 53B for double seal option on critical services

Bearing Housing

  • Centerline mounted – maintains alignment as pump casing expands with hot water

  • Air cooled – sufficient for up to 200°C service

  • Optional water cooling – for ambient temperatures >40°C or very hot water

Comparison: BB2 Booster Pump vs. Other Boiler Feed Pump Types

FeatureBB2 (Booster)BB3/BB5 (Main HP Feed)OH2 (Small Feed)
Pressure capability≤60 barup to 400+ bar≤30 bar
Flow range50–3500 m³/h100–3000 m³/h5–600 m³/h
NPSH performanceExcellent (double suction)Moderate (inducer options)Good
Best forBooster, medium pressure boilerHigh pressure main feedPackage boilers
API 610 complianceYes (BB2)Yes (BB3/BB5)Yes (OH2)

Why Power Plants & Refineries Choose Hyrig Boiler Feed Booster Pump BB2

  • Proven low NPSH operation – reduces deaerator elevation requirements

  • Long bearing life – API 610 minimum 25,000 hours

  • Easy maintenance – radially split casing allows rotor removal without disturbing pipe spools

  • Cost effective – lower installed cost than multistage pumps for medium pressure duties

Need a Boiler Feed Booster Pump BB2 for your boiler house, cogeneration plant, or refinery?
Contact Hyrig for a detailed proposal, pump sizing, or seal plan recommendation.

Email: info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit