Hyrig’s Fractionator Bottoms Pump BB2 is a heavy duty centrifugal pump manufactured per API 610 (ISO 13709), BB2 type. This horizontally mounted, radially split, two-bearing supported pump is specifically engineered for handling the bottoms stream from a main fractionator tower – a critical service in refineries and petrochemical plants. Common applications include FCC (fluid catalytic cracking) main fractionator bottoms, delayed coker fractionator bottoms, hydrocracker fractionator bottoms, and atmospheric or vacuum column side draw bottoms when high reliability is required.
Why the BB2 configuration for fractionator bottoms?
Fractionator bottoms are typically:
High temperature (300–400°C / 570–750°F)
Low NPSH available (tower bottom liquid level often limited)
Contaminated with catalyst fines (in FCC bottoms) or coke particles (in coker service)
Moderate to high viscosity at pumping temperature
The API 610 BB2 configuration is ideal because:
Two bearing supports + centerline mounting – handles thermal expansion without misalignment
Radially split casing – easy maintenance without disturbing piping (for many designs)
Double suction impeller option – lowers NPSH requirement for larger flows (typical >1000 m³/h)
Single suction with inducer – suitable for smaller flows with difficult NPSH
Heavy duty bearing housing – with cooling for high temperature operation
Typical Operating Parameters
| Parameter | Range |
|---|---|
| Flow rate | 50 – 3,500 m³/h (220 – 15,400 USgpm) – typical FCC bottoms rates can be large |
| Head | 40 – 200 m (131 – 656 ft) – for bottoms circulation, charge to downstream, or heat exchanger train |
| Temperature | 250°C – 415°C (482°F – 779°F) – depending on fractionator type |
| Inlet pressure (at pump flange) | ≤10 bar (≤145 psi) – fractionator normally at slight positive pressure |
| Design pressure (casing) | 20 – 60 bar – per system design |
| Speed | 980 / 1480 / 2980 rpm – slower speed for high viscosity/abrasive service |
Key Applications for Fractionator Bottoms Pump BB2
| Unit | Service Description |
|---|---|
| FCC Main Fractionator | Pumping heavy slurry or bottoms to slurry settler, or as recycle to fractionator bottom |
| Delayed Coker Fractionator | Transferring coker bottoms (heavy gas oil / pitch) to downstream coker heater or quench |
| Hydrocracker Fractionator | Bottoms pump for unconverted oil recycle or product downgrading |
| Crude Atmospheric Column | Bottoms recirculation (larger units may use BB2; generally smaller units use OH2) |
| Vacuum Flasher / Reboiler circulation | High temperature bottoms circulation |
Design Features for Reliable Fractionator Bottoms Service
Solids Resistance (for FCC or coker service)
Hard faced wear rings – Stellite or tungsten carbide coating to resist catalyst/coke fines erosion
Optional abrasion resistant impeller – chrome white iron or ceramic coating
Low velocity volute design – reduces particle impact erosion
High Temperature Materials
Casing/Impeller: Carbon steel ASTM A216 WCB up to 425°C; Chrome-moly A217 WC6 (up to 540°C) for high temp service
Bolting: ASTM A193 B7/B16 for elevated temperatures
Bearing cooling: Water cooled housings for pumped fluid >200°C
Sealing System (API 682)
Standard: Single cartridge seal with API Plan 32 (external clean flush) to keep solids away from seal faces + Plan 62 (quench)
For FCC slurry: Tandem seal with Plan 52 + continuous external flush of clean oil
For coker bottoms: Double seal with Plan 53B for maximum safety against hot flammable service
Low NPSH Features
Double suction impeller – reduces NPSHr by factor of 4 compared to single suction (for same specific speed)
Inducer – optional for smaller single suction BB2 designs
Larger impeller eye – increases suction specific speed, lowering NPSHr
Comparison with Other Pump Types for Fractionator Bottoms
| Pump Type | Suitability | Remarks |
|---|---|---|
| OH2 | Limited to smaller sizes (<500 m³/h) | Nozzle loads and thermal growth problematic for large, hot pumps |
| BB2 | Best fit for 100–3500 m³/h | Optimal balance of cost, reliability, and maintainability |
| BB3/BB5 | Overkill | Unnecessary high head capability adds cost and complexity |
| Vertical turbine | Not typical | Requires pit, difficult solids handling |
Why Refineries Choose Hyrig Fractionator Bottoms Pump BB2
Designed for continuous duty in hot, dirty, low NPSH service
API 610 compliance ensures 20,000+ hour bearing life and minimum 3 years MTBM (mean time between maintenance)
Proven resistance to catalyst fines (FCC) and coke particles (coker)
Centerline mounting eliminates alignment shifts due to thermal growth
Flexible seal plan selection per API 682
Case Example (typical for reference)
A 200,000 bbl/day FCC unit required a main fractionator bottoms pump for 1800 m³/h at 85 m head, 370°C, with NPSHa of only 3.5 m. Hyrig supplied a BB2 pump with double suction impeller, hard faced wear rings, and tandem seals (Plan 52). The pump has operated for 4 years with no unplanned downtime.
Need a Fractionator Bottoms Pump BB2 for your Main Fractionator or Coker?
Contact Hyrig for a technical data sheet, application review, or custom quote.
Email: info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.