Hyrig High Temperature Oil Sands Pump BB2 – API 610 with Abrasive Resistant Coatings

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Hyrig BB2 pump engineered for high temperature oil sands service (bitumen, diluted bitumen, hot slurry). Abrasive resistant coatings on wetted parts (tungsten carbide, chromia). Handles fines up to 350°C. Double suction option reduces NPSH. API 610, centerline mounted. Up to 3000 m³/h, 200 m head. Contact info@hyrig.com.

Conatct For Details
DetailReview(0)Additional

Hyrig's High Temperature Oil Sands Pump BB2 is a heavy duty centrifugal pump manufactured per API 610 (ISO 13709), BB2 type, specifically designed for the demanding conditions of oil sands processing – including hot bitumen, diluted bitumen (dilbit), thermal cracked residues, and moderate solids-laden hydrocarbon streams. The BB2 configuration, combined with abrasive resistant coatings, provides extended service life in high temperature, erosive environments typical of oil sands extraction and upgrading.

Where does the BB2 pump fit in oil sands processing?
Oil sands operations involve several high temperature, abrasive services where a BB2 pump with proper coatings is an excellent choice:

ApplicationTemperatureSolids ContentPump Type Recommendation
Diluted bitumen (dilbit) transfer80–150°C<0.5% finesBB2 with coating
Hot bitumen (after froth treatment)150–250°C1–3% sand/clayBB2 with coating
Thermal cracker bottoms (bitumen upgrading)300–350°C2–5% coke finesBB2 with heavy coating
High concentration tailings50–70°C20–40% solidsNot BB2 – use slurry pump
Primary extraction hydrotransport40–60°C30–50% solidsNot BB2 – use heavy duty slurry pump

For high solids tailings, Hyrig recommends other designs (e.g., horizontal slurry pump or submersible). The BB2 is optimized for low to moderate solids (<5% by weight) at elevated temperatures.

Why the BB2 configuration for high temperature oil sands?

  • Two bearing supports – stable rotor dynamics for continuous duty

  • Centerline mounting – allows thermal expansion up to 350°C without misalignment

  • Double suction impeller option – lowers NPSH requirement when pumping from vessels under vacuum or low head

  • Radially split casing – maintains integrity under thermal cycling; easier maintenance than axial split designs at high temperature

  • Heavy duty bearing housing – with water cooling for all services above 200°C

Abrasive Resistant Coatings – Key to Reliability
Oil sands fluids contain quartz sand, clay, and other abrasive particles. Hyrig applies advanced coatings to all wetted parts (impeller, casing wear rings, shaft sleeves, and volute liner areas):

Coating TypeHardness (HV)Max TempBest For
Tungsten carbide (HVOF)1100–1300540°CSevere abrasion + high temperature – ideal for bitumen with quartz sand
Chrome oxide (Cr2O3) plasma spray1200–1400540°CExcellent wear resistance, smooth finish
Stellite 6 hardfacing (weld overlay)350–450800°CHigh impact areas (impeller vane leading edges)
Ni-Hard cast iron (for casing liners)500–600400°CCost effective for moderate abrasion

Typical Operating Parameters (with coatings)

ParameterRange
Flow rate100 – 3,000 m³/h (440 – 13,200 USgpm)
Head30 – 200 m (100 – 650 ft) – single stage; up to 350 m for two-stage BB2
TemperatureUp to 350°C (662°F) for thermal cracking residues; 250°C typical for hot bitumen
Inlet pressure≤20 bar (290 psi) – dependent on upstream vessel
Discharge pressureUp to 60 bar (870 psi)
Speed980/1480/2980 rpm – slower speeds recommended for abrasive service

Design Features for Oil Sands Abrasive Service

Materials of Construction

  • Casing: Carbon steel (A216 WCB) with internal coating; ASTM A217 WC6 (chrome-moly) for >350°C

  • Impeller: 12% chrome (CA6NM) with HVOF tungsten carbide coating on all flow surfaces

  • Wear rings: 17-4 PH stainless steel + stellite hardfacing

  • Shaft sleeve: 316 SS or Alloy 625 with ceramic coating

Sealing System (API 682)

  • Primary: Tandem mechanical seal (API Plan 52) with external clean flush (Plan 32) using filtered diluent to keep abrasives away from seal faces

  • Alternative: Double pressurized seal (Plan 53B) for zero emissions in environmentally sensitive areas

  • Flush fluid: Clean diluent (naphtha or light gas oil) injected at 5–10 L/min per seal

Bearing Housing Cooling

  • Water cooled (integral jacket) mandatory for all services >150°C

  • Oil mist lubrication optional for extended life in continuous operation

  • Bearing temperature monitoring (RTD probes) for predictive maintenance

Flow Velocity Control

  • Low impeller tip speed (<45 m/s) – reduces erosive wear

  • Optimized volute design – minimizes localized high velocity zones

Operational Recommendations for Abrasive Service

  • Maintain minimum continuous flow to prevent recirculation erosion

  • Use variable frequency drive (VFD) to reduce speed and wear when possible

  • Install a temporary strainer during commissioning to remove system debris

  • Plan scheduled inspection of wear ring clearances (replace when gaps increase by 50%)

Comparison with Other Pump Types for Oil Sands

Pump TypeSuitable for High Temp Oil Sands?Remarks
OH2 (overhung)Limited to small flows (<500 m³/h)Overhung rotor less stable at high temp; nozzle loads issue
BB2 (with coatings)Yes – optimum for medium flow, abrasive, high tempBest life/cost balance for dilbit, hot bitumen, cracker bottoms
BB3/BB5 (multistage)NoUnnecessary head; abrasives cause rapid multistage wear
Slurry pump (heavy duty)No – usually low temp onlyNot designed for high temperature hydrocarbon service

Why Oil Sands Operators Choose Hyrig BB2 with Abrasive Resistant Coatings

  • Extended wear life – HVOF tungsten carbide coating provides 3–5x life over uncoated 12% chrome

  • High temperature integrity – centerline mounting and water cooled bearings prevent thermal damage

  • API 610 compliance – ensures bearing life >25,000 hours and reliable operation

  • Proven in SAGD, CSS, and bitumen upgrading – field references available

  • Custom coating package – matched to your specific solids type and concentration

Case Example
A Canadian oil sands upgrader required a pump for hot cracker bottoms (320°C, 3% coke fines, 1800 m³/h at 95 m head). Hyrig supplied a BB2 with HVOF tungsten carbide coated impeller and wear rings, tandem seals with Plan 52 + external flush, and water cooled bearings. After 18 months, wear ring clearance increased only 0.3 mm – projected life 5+ years.

Need a High Temperature Oil Sands BB2 Pump with Abrasive Resistant Coatings?
Contact Hyrig for a coating recommendation, wear life estimate, and detailed quote.

Email: info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit