API Butt Weld End Valve RFQ Checklist | Bore & NDT

2026-11-15 20:42

API Butt Weld End Valve RFQ Checklist

HYRIG can supply API butt weld end valves. Because the valve bore must match the adjoining pipe Schedule and the joint requires specific welding and NDT procedures, the initial Request for Quotation (RFQ) must include precise dimensional and testing data.

Key Facts

  • Critical Dimension: Pipe Inside Diameter (ID), not just Nominal Pipe Size (NPS)
  • Standard Reference: ASME B16.25 for bevel geometry
  • Weld Type: Full-penetration groove weld
  • Inspection: RT (Radiographic) or PAUT (Phased Array Ultrasonic)

Key Specifications

To receive an accurate quote and ensure the valve fits the pipeline, provide the following data in your RFQ:

Data FieldWhy It Is Needed
Pipe Outside Diameter (OD)Confirms the valve end OD matches the pipe.
Pipe Wall Thickness / ScheduleDetermines the bore ID (C dimension) to prevent a weld root step.
Pipe MaterialEnsures valve body material is compatible to avoid dissimilar metal issues.
Design Pressure & TemperatureDefines the valve pressure class (e.g., Class 150, 300, 600).
Valve TypeSpecifies body construction (e.g., ball, gate, globe, check).
NDT RequirementDefines if RT or PAUT is required for the field weld.
PWHT RequirementIndicates if post-weld heat treatment is needed (affects trim material).

Dimensions

DimensionStandard
Bevel GeometryASME B16.25
Face-to-FaceASME B16.10
Pipe DimensionsASME B36.10M

Structure and Working Principle

When quoting a butt weld end valve, the most common error is specifying the valve by NPS without specifying the pipe Schedule. A 6-inch valve with a Schedule 40 bore has a different internal diameter than a 6-inch valve with a Schedule 80 bore.

If the valve bore does not match the pipe ID, the welding contractor will face a mismatch at the root. This creates a step, which can cause turbulence, erosion, or fail radiographic acceptance. Providing the pipe OD, wall thickness, and material ensures the factory can machine the bore to match (Dimension C).

Cross-Reference and Replacement

When preparing an RFQ for a replacement valve:

  1. Measure the Existing Pipe: Do not assume the pipe Schedule based on the original valve NPS. Measure the pipe OD and wall thickness directly.
  2. Check the Bevel: Confirm the existing pipe has a standard 37.5° bevel. Custom bevels must be specified.
  3. Specify Documentation: State whether you need material certificates (EN 10204 3.1), NDT reports, or WPS/PQR support.

Applications

  • Pipeline Construction: Ensuring new valves match the specified pipe schedule before fabrication.
  • Maintenance & Turnarounds: Ordering replacement valves that drop into existing welded piping without pipe modification.
  • Toxic & High-Pressure Service: Verifying the NDT and material requirements match the line class specification.

Disclaimer: This equipment is designed for high-pressure industrial applications. Welding procedures and NDT requirements are project-specific. Verify pressure ratings and joint integrity requirements prior to installation.

Frequently Asked Questions

Q: What happens if the valve bore doesn't match the pipe ID?

A mismatch creates a step at the weld root, causing turbulence, erosion, and potential failure during RT or PAUT inspection. The valve must be machined to match the pipe ID.

Q: Do you provide WPS and PQR for field welding?

The manufacturing partner can provide standard WPS/PQR documentation for reference. However, the field welding contractor is typically responsible for ensuring the procedure complies with the project piping specification.

Q: What is the typical lead time for a butt weld end valve?

Standard lead time is 4 to 6 weeks depending on the valve type, size, and NDT/documentation requirements.

Selection Support

To ensure the valve matches your pipeline, provide the pipe OD, wall thickness, and material. Our engineering team will confirm the machined bore (C dimension) and bevel geometry.

Contact

For API butt weld end valve RFQ support, contact HYRIG: info@hyrig.com

Related Pages

Name:
Message:
Verification code:
Submit
Comment