API Butt Weld End Valve | ASME B16.25 Bevel & Bore Match

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply API butt weld end valves. A butt weld end is a pipe-to-valve joint preparation machined to ASME B16.25, not a valve body construction.
Conatct For Details
DetailReview(0)Additional

API Butt Weld End Valve

HYRIG can supply API butt weld end valves. A butt weld end is a pipe-to-valve joint preparation machined to ASME B16.25, not a valve body construction. The end features a 37.5-degree bevel and is matched to the adjoining pipe Schedule to ensure a smooth internal bore for welding.

Key Facts

  • End Standard: ASME B16.25
  • Bevel Angle: 37.5° ± 2.5° (75° included)
  • Root Face: 1.6 ± 0.8 mm
  • Size Coverage: NPS 2 1/2 to NPS 24
  • Schedule Coverage: 40, 80, 120, 160, XXS, and selected STD/XS
  • Bore Matching: Machined ID to match pipe ID
  • NDT: RT or PAUT per project specification
  • Applicable Valve Standards: API 6D, API 600, API 608, BS 1873

Key Specifications

NPSScheduleOD A (mm)Pipe ID B (mm)Machined ID C (mm)Wall T (mm)
640168.3154.1154.797.1
680168.3146.3148.0311.0
6160168.3131.7135.2818.3
6XXS168.3124.4128.8321.9
840219.1202.7203.718.2
880219.1193.7195.8112.7
8120219.1182.5186.0818.3
8XXS219.1174.6179.1522.2

Dimensions

DimensionRequirement
Bevel Angle37.5° ± 2.5° per end
Root Face (Land)1.6 ± 0.8 mm
Bore ToleranceMachined to match pipe ID for specified Schedule
Wall Thickness > 22 mmCompound bevel or taper bore
Backing RingNot used; intended for welding without backing ring

Structure and Working Principle

A butt weld end creates a full-penetration groove weld between the valve and the pipe. The ASME B16.25 bevel ensures the weld root sits flush with the pipe bore, producing a smooth internal surface with no crevice at the joint.

This design is standard for pigged lines, toxic service, and cyclic high-pressure systems. The joint can be fully radiographed, and there is no gasket or bolted interface to loosen under thermal cycling. The critical procurement variable is bore matching: the valve's machined inside diameter (C) must correspond to the pipe inside diameter (B) for the specified Schedule, not merely to the valve NPS.

Cross-Reference and Replacement

When replacing a flanged valve with a butt weld end valve, verify these factors before cutting pipe:

  1. Pipe Schedule and Wall Thickness: Confirm the OD and wall thickness of the existing pipe. The valve bore must match the pipe ID, not the nominal size.
  2. Bevel Preparation: The valve end is pre-machined to ASME B16.25. Confirm the field bevel matches the 37.5° geometry and root face.
  3. NDT Scope: Determine whether the project requires RT or PAUT. This affects the welding procedure and inspection cost.
  4. PWHT Requirement: If the pipe material or wall thickness triggers post-weld heat treatment, confirm the valve trim and seat materials can withstand the PWHT temperature.

Applications

  • Long-distance transmission pipelines: Permanent welded joints remove the bolted flange leak path on buried and remote sections.
  • Pigged lines: Full-penetration weld and matched bore allow inspection gauges to pass without obstruction.
  • Toxic and hazardous media: No gasket interface eliminates a potential external leak path.
  • High-temperature and cyclic service: Welded joints distribute stress and avoid bolt preload loss under thermal cycling.

Disclaimer: This equipment is designed for high-pressure industrial applications. Welding procedures and NDT requirements are project-specific. Verify pressure ratings and joint integrity requirements prior to installation.

Frequently Asked Questions

Q: Is a butt weld end a type of valve?

No. A butt weld end is a pipe-to-valve joint preparation. The same valve body can be supplied with flanged, socket weld, or butt weld ends.

Q: How do I specify the correct bore for a butt weld end valve?

Provide the pipe outside diameter, wall thickness or Schedule, and material. The valve bore is machined to the pipe ID, not to the valve nominal size.

Q: What NDT is required for a butt weld end joint?

RT or PAUT is typical for full-penetration butt welds. The exact percentage and acceptance criteria are defined by the piping specification and service category, not by the valve standard alone.

Q: What is the typical lead time?

Standard lead time is 4 to 6 weeks depending on valve type, size, material, and NDT/documentation scope.

Selection Support

To confirm the correct end preparation and bore for your pipeline, provide the pipe Schedule, material, and NDT requirement. Our engineering team will verify the bevel geometry and machined bore against ASME B16.25 and the adjoining pipe specification.

Contact

For API butt weld end valve selection, contact HYRIG: info@hyrig.com

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit