API 6D Swing Check Valve | Class 150-2500 RF/RTJ/BW

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the API 6D swing check valve range. The API 6D swing check valve is a non-return valve with a hinged disc that swings open under forward flow and returns to the seat when flow
Conatct For Details
DetailReview(0)Additional

API 6D Swing Check Valve

HYRIG can supply the API 6D swing check valve range. The API 6D swing check valve is a non-return valve with a hinged disc that swings open under forward flow and returns to the seat when flow reverses. It is specified for Class 150-2500 pipelines where low pressure drop and full-bore flow are required.

Key Facts

  • Design standard: API 6D, BS 1868
  • Pressure class: Class 150 / 300 / 600 / 900 / 1500 / 2500
  • Size range: NPS 2-36 (DN 50-900)
  • Disc type: Swing disc
  • Body/bonnet connection: Bolted (Class 150-900), pressure seal (Class 1500-2500)
  • Seat: Metal-seated, hard alloy overlay; welded or renewable
  • End connections: RF, RTJ, BW
  • Testing: API 598, API 6D

Key Specifications

NPSDNClass 150 L RF (mm)Class 150 L RTJ (mm)Class 150 L BW (mm)Class 150 d (mm)Class 150 Wt (kg)Class 300 L RF (mm)Class 300 L RTJ (mm)Class 300 L BW (mm)Class 300 d (mm)Class 300 Wt (kg)
25020321620351142672832675122
38024125424176243183333187644
41002923052921024335637135610257
615035636835615272445460445152120
8200495508495203124533549533203194
10250622635622254196622638622254290
12300699711699305330711727711305450

Data source: Technical data table.

Dimensions

DimensionStandard
Face-to-face (RF)ASME B16.10
Face-to-face (RTJ)ASME B16.10
Face-to-face (BW)ASME B16.10
Flanged endsASME B16.5 / ASME B16.47
Butt weld endsASME B16.25
Pressure-temperature ratingASME B16.34
Wall thicknessAPI 600 / BS 1868

Structure and Working Principle

The disc is suspended from a hinge pin near the top of the body. Forward flow pushes the disc open, clearing the flow path and producing a low pressure drop. When flow stops or reverses, gravity returns the disc to the seat.

Class 150-900 valves use a bolted bonnet with studs and nuts. Class 1500-2500 valves use a pressure-seal bonnet, where line pressure assists the seal. Carbon steel valves typically use a forged seat ring with hard-alloy overlay. NPS 8 and below can be supplied with a renewable threaded seat; NPS above 8 is welded-on seat. Stainless steel valves usually use an integral seat with hard facing.

Cross-Reference and Replacement

Replacing a swing check valve requires verification of four factors:

  1. Face-to-face dimension: RF, RTJ, and BW lengths differ. Confirm the piping gap against the L dimension for your end type.
  2. Installation orientation: Standard swing check valves are for horizontal or vertical upward-flow lines.
  3. Water hammer risk: Swing discs close slowly on flow reversal. Assess whether a lift/piston design or damped swing design is required for long vertical risers or high-velocity lines.
  4. End connection: Confirm whether the existing line uses RF, RTJ, or BW, and whether the flange drilling matches ASME B16.5 or B16.47.

Applications

  • Pump discharge lines (large sizes): Low pressure drop is preferred where energy consumption matters.
  • Pipeline pigging: Full-bore swing design allows pigs to pass when the disc is fully open.
  • Steady-flow process lines: Suitable for clean fluids where rapid closure is not critical.
  • Refinery and petrochemical piping: Standard non-return protection for Class 150-2500 systems.

Disclaimer: This equipment is designed for high-pressure industrial applications. Ensure strict compliance with local safety standards and verify pressure ratings prior to installation. Water hammer risk must be assessed for the specific piping system.

Frequently Asked Questions

Q: What is the difference between a swing check valve and a lift check valve?

A swing check valve uses a hinged disc with low pressure drop and slow closure. A lift (piston) check valve uses a guided disc with faster closure and tighter sealing, but higher pressure drop.

Q: Can a swing check valve be installed vertically?

Yes, for upward flow. Downward-flow vertical installation is not standard and requires confirmation.

Q: What is the typical lead time?

Standard lead time is 4 to 6 weeks depending on size, class, material, and end connection.

Q: Is a piggable design available?

Full-bore swing check valves can be configured for pigging on request. Confirm the pig diameter and line velocity with the engineering team.

Selection Support

Not sure whether a swing or lift check valve fits your line? Provide the line size, pressure class, flow direction, and whether pigging is required; our engineers will confirm the correct disc type and end connection.

Contact

For API 6D swing check valve selection, contact HYRIG: info@hyrig.com

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit