The Deep Well Pump is an API 610 Type VS1 vertical, single casing, multistage turbine pump specifically engineered for water extraction from deep wells, boreholes, wet pits, and open sump installations. The pump fully complies with API 610 11th Edition and ISO 13709 standards.
The VS1 configuration is a vertically suspended, single casing, diffuser type pump with discharge through a column pipe. The pump bowl assembly is submerged below the minimum operating liquid level, while the driver and discharge head remain above grade. Multiple stages are stacked vertically to achieve required head. This design is ideal when available Net Positive Suction Head (NPSHa) is insufficient for horizontal pumps.
As a specialized China API 610 pump manufacturer, we produce VS1 deep well pumps for continuous duty in water supply, hydrocarbon transfer, chemical service, and industrial applications.
| Medium | Suitability |
|---|---|
| Fresh water / Groundwater | Excellent – standard construction |
| Industrial process water | Excellent – clean service |
| Hydrocarbons (crude, diesel, naphtha) | Excellent – with carbon steel / mechanical seals |
| Sea water / Brackish water | Excellent – with duplex or super duplex |
| Chemical process fluids | Good – with 304/316SS or high alloys |
| Corrosive / acidic fluids | Limited – requires specialized materials |
The pump handles clean or slightly polluted liquids, hot or cold fluids, neutral or corrosive media depending on material selection.
| Parameter | Range |
|---|---|
| Flow rate (Q) | 10 ~ 13,000 m³/h |
| Total head (H) | Up to 2,300 m (multiple stages) |
| Operating temperature | -200°C ~ +350°C |
| Design pressure | Up to 200 bar |
| Speed | 1,450 / 2,980 / 3,600 rpm |
| Flange rating | ASME Class 150 / 300 / 600 |
| Installation depth | Up to 40 m |
| Feature | Benefit |
|---|---|
| Vertically suspended configuration | Pump bowl assembly submerged, driver at grade – ideal for limited NPSH conditions |
| Single casing diffuser type | Diffuser vanes between stages provide smooth hydraulics and high efficiency |
| Multistage stacking | Multiple stages vertically stacked achieve high head in minimal footprint |
| Single or double suction first stage | Single suction standard; double suction improves NPSH for critical low headroom conditions (ultra low NPSHR applications) |
| Axial thrust balance | Balance drum + angular contact bearing compensates thrust for extended bearing life |
| Renewable wear rings and bushings | Inter-stage bushings and diffuser rings replaceable – restores efficiency without replacing major castings |
| Line shaft with centralizers | Stainless steel line shaft with guide rings and centralizers for deep well stability – prevents vibration, ensures alignment |
| API 682 seal chamber | Discharge head accommodates single, tandem, or double mechanical seals with required flush plans |
| Bearing lubrication options | Product lubricated (process fluid) for clean water; oil lubricated for hydrocarbons and critical services |
| Strainer / Suction bell | Prevents debris entry; options include basket or conical strainers |
| Component | Fresh Water Service | Hydrocarbon / Corrosive Service |
|---|---|---|
| Bowl assembly | Cast iron | 304SS / 316SS / Duplex / Titanium |
| Impellers | Cast iron / Bronze | 304SS / 316SS / Duplex |
| Diffusers | Cast iron / Bronze | 304SS / 316SS / Duplex |
| Line shaft | AISI 1045 / 416SS | 17-4PH / Duplex |
| Column pipe | Carbon steel (threaded/flanged) | 304SS / 316SS |
| Discharge head | Cast iron / Fabricated steel | 304SS / 316SS |
| Wear rings / Bushings | Bronze / Silicon carbide | Silicon carbide / Stellite faced |
| Fasteners | A193 B7 | A193 B8M (316SS) |
| Industry | Typical Deep Well / VS1 Service |
|---|---|
| Oil & Gas Upstream | Crude oil transfer from well pads, water injection, produced water handling |
| Oil & Gas Downstream | Refinery process water, cooling water, tank farm transfer, hydrocarbon transfer |
| Petrochemical | Chemical process water, circulating water, waste water |
| Power generation | Cooling water intake, condensate extraction, auxiliary service water |
| Chemical plants | Raw water supply, process fluid transfer, corrosive chemical pumping |
| Water supply | Municipal water extraction, industrial raw water, irrigation |
| Marine / Offshore | Seawater lift for cooling and firewater systems |
| Mining | Dewatering, pit drainage, process water circulation |
Full API 610 11th Edition (ISO 13709) compliance – same standards as leading global brands
Complete material range – cast iron, carbon steel, 304/316SS, duplex, super duplex, titanium, Hastelloy, NACE compliance
Hydraulic flexibility – radial flow (high head) or mixed flow (high flow) hydraulics available
Wide performance envelope – flows to 13,000 m³/h, heads to 2,300 m (radial) / 600 m (mixed flow), pressures to 200 bar, temperatures -200°C to +350°C
Installation depth – up to 40 meters (standard); longer custom lengths available
API 682 seal support – complete seal flush panels and support systems
Competitive cost – 20–30% lower than Western equivalents
Lead time – 20–28 weeks for standard configurations
Factory testing – hydraulic performance, NPSH, mechanical run, vibration monitoring
Full documentation – performance curves, GA drawings, material certifications
| Parameter | Specification |
|---|---|
| Pump Type | API 610 Type VS1 – vertical, single casing, diffuser, multistage |
| Flow range | 10 ~ 13,000 m³/h |
| Head range | Up to 2,300 m (radial) / 600 m (mixed flow) |
| Temperature range | -200°C to +350°C |
| Pressure rating | Up to 200 bar |
| Speed | Up to 3,600 rpm |
| Casing | Single casing, diffuser type, wet pit |
| Impellers | Single or mixed flow, open or enclosed |
| Stages | Multistage (stacked) |
| First stage | Single suction (standard) / Double suction (ultra low NPSHR) |
| Construction | Vertically suspended, line shaft, centralizers and guide rings for deep well stability |
| Strainer options | Basket, conical (for intake protection, sand filtration) |
| Seal types | API 682 (Plan 51/52/53/54), double seals for hazardous service, gland packing options |
| Lubrication | Process lubricated / Oil lubricated |
| Installation depth | Up to 40 m |
| Materials | Cast iron, carbon steel, 304/316SS, duplex, super duplex, titanium |
| Options | Inducer for low NPSH; ATEX for explosive environments; steam/electric tracing for cold climates; anodic protection for seawater; hypochlorite injection for marine growth prevention |
| Certification | API 610 11th Edition / ISO 13709 |
For more information or a custom proposal for your deep well pump (API 610 VS1) application, please contact us at:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.