The end suction centrifugal pump is the most widely used pump type across industrial, commercial, and municipal sectors. Its name derives from the suction nozzle located at the end of the casing opposite the bearing housing, while the discharge nozzle is positioned radially (typically on top). This configuration produces a compact, robust, and easy‑to‑maintain pump that handles clean and slightly dirty liquids across a vast range of flows and pressures.
Our end suction pumps are available in two quality tiers:
Standard industrial – conforming to ISO 2858 / EN 733, ideal for water, HVAC, light chemicals, and general service.
API 610 OH2 – heavy‑duty, centerline‑mounted, overhung design for refinery, petrochemical, and process plant service (20‑year design life, API 682 seals, NACE MR0175 optional).
Both designs share the back pull‑out feature: the complete rotating assembly (impeller, shaft, bearing housing, seal chamber) can be removed without disturbing the suction or discharge piping, dramatically reducing maintenance downtime.
| Parameter | Standard Industrial | API 610 OH2 |
|---|---|---|
| Flow range | 5 – 1,200 m³/h (22 – 5,300 GPM) | 10 – 600 m³/h |
| Head range | 5 – 150 m (16 – 490 ft) | 10 – 160 m |
| Pressure rating | Up to 16 bar (230 psi) | Up to 40 bar (580 psi) |
| Temperature range | –20 to +150°C (–4 to +302°F) | –45 to +260°C (–49 to +500°F) |
| Speed | 1,450 / 2,900 rpm (50Hz) ; 1,750 / 3,500 rpm (60Hz) | 1,450 / 2,950 rpm |
| Motor power | 0.55 – 250 kW (0.75 – 335 HP) | 2.2 – 250 kW |
| Materials | Cast iron, 304 SS, 316L SS | 316L SS (S‑8), duplex (D‑1/D‑2), carbon steel (C‑6) |
| Connections | Flanged (DIN/ANSI) , threaded (small) | ANSI / ASME raised face flanges |
| Mounting | Foot‑mounted (horizontal) | Centerline‑mounted (OH2) |
| Component | Standard (Cast Iron) | Premium (316L SS) | API 610 OH2 (S‑8 / Duplex) |
|---|---|---|---|
| Casing | Cast iron (GG25) epoxy coated | 316L SS (CF3M) | 316L SS or duplex |
| Impeller | Cast iron / bronze / 304 SS | 316L SS | 316L SS, 17‑4 PH, duplex |
| Shaft | 2Cr13 / AISI 420 | 316 SS | 17‑4 PH, duplex |
| Wear rings | Cast iron / bronze | 316L SS | 316L SS + Stellite |
| Mechanical seal | Carbon/ceramic/NBR | Silicon carbide/Viton | API 682 cartridge, SiC/SiC, Viton/Aflas |
| Gaskets | Non‑asbestos / EPDM | PTFE / Viton | Spiral wound graphite / PTFE |
For potable water, cast iron with epoxy coating is acceptable. For aggressive chemicals, food, pharmaceutical, or seawater, specify 316L stainless steel. For high‑chloride or sour service (H₂S), duplex with NACE MR0175 is required.
The end suction centrifugal pump features:
Single‑stage, single‑suction radial impeller – closed (enclosed) for clean liquids, semi‑open for light solids.
Volute casing with optimised cross‑section for smooth flow and high efficiency (up to 85% at BEP).
Large impeller eye – reduces NPSHr; typical NPSHr of 2‑5 m at BEP; inducer option available for lower NPSHa.
Steep, stable head‑flow curve – continuously rising to shut‑off, suitable for parallel operation.
Hydraulic axial thrust balancing – via balance holes in impeller back shroud or back vanes.
| Service | Seal Type | API 682 Plan | Materials |
|---|---|---|---|
| Clean cold water | Single cartridge | Plan 11 | Carbon / ceramic / NBR |
| Hot water (≤120°C) | Single with cooler | Plan 23 (recirculation cooler) | Silicon carbide / carbon / Viton |
| Chemical transfer (mild) | Single (SiC vs. carbon) | Plan 11 or 21 | Silicon carbide / carbon / Viton |
| Chemical (aggressive) | Single (SiC/SiC) | Plan 11 or 32 | Silicon carbide / silicon carbide / Viton or Aflas |
| Hydrocarbon / hazardous / H₂S | Dual pressurised (Arr. 3) | Plan 53B | Silicon carbide / silicon carbide / Viton or Aflas |
| Food / pharmaceutical | Single (FDA) | Plan 11 | Carbon / ceramic / EPDM or silicone |
For API 610 OH2 pumps, the seal chamber is API 682 compliant, accepting any cartridge arrangement without modification.
| Industry | Typical Applications | Why End Suction |
|---|---|---|
| Water treatment | Raw water transfer, high‑lift pump, filtered water boosting | High flow, low cost, easy maintenance |
| HVAC | Chilled water, hot water, condenser water circulation | Wide hydraulic range, quiet operation |
| Chemical processing | Acid, alkali, solvent transfer (316L SS) | Corrosion resistance, seal options |
| Food & beverage | Product transfer, CIP supply (sanitary version) | Stainless steel, easy‑clean, FDA elastomers |
| Pharmaceutical | Purified water (PW) , water for injection (WFI) | Electropolished 316L, sanitary connections |
| Refinery & petrochemical | Crude oil, refined products, chemical injection (API 610 OH2) | 20‑year life, high temperature, NACE MR0175 |
| Power generation | Cooling water, ash handling, general service | Rugged construction, long running life |
| Irrigation | Center pivot, sprinkler systems, flood control | High efficiency, cost‑effective |
Back pull‑out design – Remove rotating assembly without disturbing piping; reduces maintenance downtime by 50% or more.
High efficiency – Hydraulically optimised impeller and volute achieve up to 85% efficiency at BEP.
Wide hydraulic coverage – Flows 5 to 1,200 m³/h, heads to 160 m – one pump covers most plant duties.
Material flexibility – Cast iron, bronze, 304 SS, 316L SS, duplex, super duplex, NACE MR0175.
API 610 OH2 option – Centreline mounting, 20‑year design life, API 682 seals, for critical services.
Low NPSH – Large impeller eye and optional inducer minimise NPSHr, suitable for limited suction head.
Mechanical seal versatility – Single, tandem, dual pressurised; all API 682 plans supported.
VFD ready – Suitable for variable frequency drive operation (consult for minimum speed limits).
Global standards – ISO 2858 / EN 733 (standard) or API 610 OH2 (heavy‑duty).
Certifications – CE, ATEX, WRAS/NSF (potable water) , FDA sanitary options.
| Test | Standard Industrial | API 610 OH2 |
|---|---|---|
| Hydrostatic test | 1.5x design pressure | 1.5x MAWP |
| Performance test | ISO 9906 Grade 3 | API 610 Grade 2 or 1 |
| Mechanical run | 1 hour | Minimum 4 hours |
| NPSH test | Optional | Full verification if specified |
| Material certification | EN 10204 2.2 (3.1 on request) | EN 10204 3.1 mandatory |
| NDE | Visual only | MPI, dye penetrant, radiography as required |
| NACE MR0175 | Not required | Available on request |
Suction piping – Must be at least the pump suction diameter; keep short, straight, and use eccentric reducer (flat on top) to avoid air pockets.
Discharge piping – Install check valve and isolation valve. Provide minimum flow recirculation for prolonged low‑flow operation.
Foundation – Pump must be mounted on a rigid baseplate or concrete foundation, properly grouted. For API 610 OH2, the baseplate is heavy‑duty steel.
Alignment – Coupling alignment must be checked after installation and after first thermal cycle (especially for hot services).
Priming – End suction pumps are not self‑priming; the suction line must be flooded or a self‑priming variant must be used.
Start‑up – Close discharge valve, start motor, then slowly open discharge valve.
Never run dry – Even a few seconds damages the mechanical seal.
| Task | Frequency |
|---|---|
| Check mechanical seal for leaks | Monthly |
| Monitor motor current, vibration, bearing temperature | Weekly |
| Lubricate bearings (if grease‑fitted) | Every 6 months |
| Replace mechanical seal | 8,000 – 12,000 hours or when leaking |
| Inspect impeller and wear rings | 20,000 hours or 3 years |
| Problem | Likely Cause | Solution |
|---|---|---|
| No flow | Pump not primed, suction valve closed, impeller blocked | Prime; open valve; clean impeller |
| Low flow / pressure | Worn wear rings, air in suction, discharge valve partially closed | Replace wear rings; vent air; open discharge valve |
| Excessive power consumption | Fluid density/viscosity too high, flow too high (operating far right) | Check fluid properties; throttle discharge |
| Vibration | Cavitation, misalignment, impeller imbalance | Increase NPSHa; re‑align; balance impeller |
| Seal leaks | Worn faces, wrong elastomer, dry running | Replace seal; verify materials; ensure flooded suction |
| Motor overheats | Run dry, high ambient, voltage imbalance | Ensure priming; clean vents; check supply |
| Component | Recommended Quantity |
|---|---|
| Mechanical seal cartridge (complete) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Gasket / O‑ring kit (full) | 1 set |
| Impeller (for critical duty) | 1 |
| Shaft (for critical duty) | 1 |
Highly configurable – Choose standard industrial or API 610 OH2, material grade, seal type, and connection style.
Easy maintenance – Back pull‑out design reduces downtime and labour costs.
Energy efficient – High hydraulic efficiency lowers operating costs over 20‑year life.
Flexible mounting – Foot‑mounted (ISO) or centreline (API 610 OH2) for high‑temperature service.
Global service – Spare parts and technical support available worldwide.
Proven reliability – Thousands of units operating in water, chemical, HVAC, and refinery applications.
Competitive pricing – Factory direct with volume manufacturing.
For detailed selection of the correct end suction centrifugal pump – including flow/head requirements, fluid properties, material grade (cast iron, 304, 316L, duplex), API 610 OH2 requirement, seal plan, and motor specifications – please contact our engineering team.
Email: info@hyrig.com
Our engineers support water treatment, chemical, HVAC, refinery, and industrial projects worldwide with reliable, high‑efficiency end suction centrifugal pumps – built for long service life and easy maintenance.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.