The stainless steel standard centrifugal pump is a rugged, single‑stage, end‑suction centrifugal pump with all wetted parts manufactured from stainless steel – either 304 or 316L grade. This pump is the workhorse for industries requiring corrosion resistance, product purity, and reliable operation without the high cost of exotic alloys. It handles a wide range of fluids: from clean water and demineralised water to mild acids, alkalis, food products, pharmaceutical preparations, and seawater.
Unlike carbon steel or cast iron pumps that rust and contaminate sensitive fluids, the stainless steel pump maintains product integrity and resists pitting, crevice corrosion, and chemical attack. The pump conforms to ISO 2858 / EN 733 dimensional standards (the European standard for end‑suction centrifugal pumps) and is available as a standard industrial model or with sanitary / hygienic options for food, dairy, beverage, and pharmaceutical applications.
| Parameter | Range |
|---|---|
| Flow range | 2 – 800 m³/h (9 – 3,500 GPM) |
| Head range | 5 – 150 m (16 – 490 ft) |
| Pressure rating | Up to 16 bar (standard) , 25 bar (high‑pressure option) |
| Temperature range | –20 to +150°C (–4 to +302°F) |
| Speed | 1,450 / 2,900 rpm (50Hz) or 1,750 / 3,500 rpm (60Hz) |
| Material (wetted) | 304 SS, 316L SS (standard) , duplex (optional) |
| Impeller type | Closed (enclosed) , semi‑open (optional for solids) |
| Connection | Flanged (DIN/ANSI) , Tri‑clamp (sanitary) , threaded (small sizes) |
| Mounting | Horizontal foot‑mounted or centerline (OH2 on request) |
| Certifications | CE, FDA, 3‑A (sanitary option) , WRAS/NSF (potable water) |
| Grade | Key Properties | Typical Applications |
|---|---|---|
| 304 SS | Good general corrosion resistance, weldable, cost‑effective | Clean water, food products (milk, juice, beer), mild chemicals, HVAC |
| 304L (low carbon) | Same as 304 with improved weldability | Welded fabrication, general industrial |
| 316L SS | Molybdenum (2‑3%) adds pitting resistance against chlorides and acids | Seawater, chemical processing, pharmaceutical water (WFI), acids, alkalis |
| Duplex 2205 | Higher strength, superior chloride resistance (PREN >35) | Brackish water, seawater, marine environments |
For 90% of industrial and sanitary applications, 316L stainless steel is recommended because of its superior resistance to corrosion from chlorinated water, process chemicals, and cleaning agents (CIP).
| Component | Standard Material | Upgrade Option |
|---|---|---|
| Casing (volute) | 316L stainless steel (CF3M casting) | Duplex 2205 |
| Impeller | 316L stainless steel (closed) | Semi‑open, or 17‑4 PH (hardened) |
| Shaft | 316 stainless steel (AISI 316) | 17‑4 PH, duplex |
| Wear rings | 316L SS (soft) | 316L SS + Stellite facing |
| Mechanical seal | Carbon vs. ceramic (NBR) | Silicon carbide vs. silicon carbide (Viton/Aflas) |
| Bearing housing | Cast iron (epoxy coated) | Stainless steel (fully washdown) |
| Baseplate | Steel (grouted) or stainless steel | Stainless steel (hygienic areas) |
The pump meets ISO 2858 / EN 733 dimensions, ensuring interchangeability with other standard pumps. The back pull‑out design allows removal of the rotating assembly without disturbing suction or discharge piping.
For food, dairy, beverage, and pharmaceutical industries, the pump can be configured with:
Electro‑polished or mechanically polished wetted parts – Ra ≤0.8µm (32 µinch) , Ra ≤0.4µm available.
Sanitary connections – Tri‑clamp (ferrule) , DIN 11851, SMS, or RJT.
FDA compliant elastomers – EPDM, silicone, or Viton (FKM) certified to FDA 21 CFR 177.2600.
CIP (Clean‑in‑Place) capable – Designed to withstand hot caustic and acid cleaning cycles.
Self‑draining casing – No dead legs; full drainability to prevent product hold‑up.
Washdown motor – IP56 or IP66 enclosure, stainless steel exterior.
3‑A certification available on request.
| Service | Seal Faces | Elastomer | Suitability |
|---|---|---|---|
| Clean water, light chemicals | Carbon vs. ceramic | NBR / EPDM | Standard, low cost |
| Hot water (up to 120°C) | Silicon carbide vs. carbon | Viton | High temperature |
| Corrosive acids / chemicals | Silicon carbide vs. silicon carbide | Viton / Aflas | Maximum chemical resistance |
| Abrasive fluids | Tungsten carbide vs. silicon carbide | Viton | Extended life |
| Food / dairy / pharmaceutical | Carbon vs. ceramic (FDA) | EPDM / silicone | Sanitary, FDA compliant |
The seal chamber is designed to accept single or tandem cartridge seals, with flush plans including Plan 11 (self‑flush), Plan 21 (cooled flush), Plan 23 (recirculation with cooler), and Plan 53B (dual pressurised for hazardous service).
| Industry | Typical Fluids | Why Stainless Steel |
|---|---|---|
| Chemical processing | Acids (dilute), alkalis, solvents, salt solutions | Resists corrosion; 316L for chlorides |
| Food & beverage | Milk, juice, beer, wine, edible oils, syrups, sauces | Non‑toxic, easy to clean, FDA compliant |
| Pharmaceutical | Purified water (PW) , water for injection (WFI) , buffer solutions | High purity, electropolished finish, no contamination |
| Water treatment | Demineralised water, reverse osmosis permeate, seawater (316L/duplex) | Resists corrosion and bio‑fouling |
| Marine / offshore | Seawater cooling, firewater, wash‑down | 316L or duplex prevents pitting |
| Pulp & paper | Bleach chemicals, coating preparations | Resistant to aggressive chemicals |
| HVAC | Chilled water, hot water, glycol mixtures | Long life in closed loops |
| Wastewater | Industrial effluent, leachate | Corrosion‑resistant for aggressive streams |
Corrosion resistance – 316L SS wetted parts prevent rust, pitting, and contamination.
High efficiency – Closed impeller and optimised volute achieve up to 85% hydraulic efficiency.
Easy maintenance – Back pull‑out design allows seal and bearing replacement without removing piping.
Versatile connections – Flanged (DIN/ANSI) , sanitary tri‑clamp, or threaded options.
Wide temperature range – Suitable for hot water up to 150°C and cold liquids down to –20°C.
Low NPSH – Large impeller eye design reduces NPSHr; inducer option for lower NPSHa.
Silent operation – Precision‑balanced rotor and robust bearing housing keep noise low.
Flexible mounting – Foot‑mounted (standard) or centreline (OH2) for high‑temperature service.
Global standards – ISO 2858 / EN 733 dimensions, interchangeable with major brands.
Full certification – Material certificates (EN 10204 3.1) , hydrostatic test, performance test available.
Hydrostatic test – Casing tested at 1.5x maximum working pressure.
Performance test – Water at rated speed per ISO 9906 Grade 3 or 2.
Mechanical run test – 1 hour minimum (4 hours for API 610 option).
Material certification – EN 10204 3.1 for wetted parts (standard) , 3.2 on request.
Positive Material Identification (PMI) – Optional verification of 304/316L grade.
Surface finish test (sanitary) – Ra measurement with profilometer.
Certifications – CE, FDA, 3‑A (upon request) , WRAS/NSF for potable water.
Suction piping – Must be at least the pump suction diameter; keep short and straight. Use eccentric reducer (flat on top).
Discharge piping – Install check valve and isolation valve. Provide minimum flow recirculation if the pump may run at low flow for extended periods.
Foundation – Pump must be mounted on a solid, level baseplate or concrete foundation, properly grouted.
Alignment – Coupling alignment must be checked after installation and after first thermal cycle.
Priming – Centrifugal pumps are not self‑priming; the suction line must be flooded or a self‑priming version must be specified.
VFD operation – Suitable for variable frequency drive use; consult for minimum speed to avoid bearing damage.
| Task | Frequency |
|---|---|
| Check mechanical seal for leaks | Monthly |
| Monitor motor current, vibration, bearing temperature | Weekly |
| Lubricate bearings (if grease‑fitted) | Every 6 months |
| Replace mechanical seal | 8,000 – 12,000 hours or when leaking |
| Inspect impeller and wear rings | 20,000 hours or 3 years |
| Problem | Likely Cause | Solution |
|---|---|---|
| Low flow or no flow | Pump not primed, suction valve closed, impeller blocked | Prime pump; open valve; clean impeller |
| Low pressure | Worn wear rings or impeller, air in suction | Replace wear rings; vent air; check for air leaks |
| Excessive power consumption | Specific gravity too high, viscosity too high, flow too high (operating far right on curve) | Check fluid properties; throttle discharge valve |
| Pump vibrates | Cavitation, misalignment, impeller imbalance | Increase NPSHa; re‑align; balance impeller |
| Seal leaks | Worn faces, incorrect elastomer, dry running | Replace seal; verify materials; ensure flooded suction |
| Overheating | Run dry, restricted cooling, high ambient | Ensure priming; clean motor vents; reduce ambient if possible |
| Component | Recommended Quantity |
|---|---|
| Mechanical seal kit (complete) | 1 set |
| Bearing set (radial + thrust) | 1 set |
| Wear ring set (casing + impeller) | 1 set |
| Gasket / O‑ring kit (full) | 1 set |
| Impeller (for critical duty) | 1 |
| Shaft (for critical duty) | 1 |
For detailed selection of the correct stainless steel standard centrifugal pump – including flow/head requirements, fluid properties (corrosivity, temperature, viscosity), material grade (304, 316L, duplex), mechanical seal type, sanitary or industrial configuration, and certification needs – please contact our engineering team.
Email: info@hyrig.com
Our engineers support chemical, food, pharmaceutical, water treatment, and industrial projects worldwide with reliable, high‑efficiency stainless steel standard centrifugal pumps – corrosion‑resistant, easy to maintain, and built for long service life.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.