Pressure Booster System – Automatic Water Pressure Boosting Pump Set with Tank & Switch

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Complete automatic pressure booster system – a self-priming centrifugal pump combined with a small pressure tank, pressure switch, and gauge. Maintains stable water pressure for household supply, garden irrigation, and small commercial applications. Draws from tanks, wells, or low‑pressure mains. Flow up to 8 m³/h, pressure up to 5 bar, suction lift up to 8 m. Quiet, corrosion‑resistant, and easy to install. Includes dry‑run and thermal protection.

Conatct For Details
DetailReview(0)Additional

Product Overview

A pressure booster system (also called an automatic water pressure pump set or domestic booster set) is a complete, ready‑to‑install unit that automatically increases and stabilises low or fluctuating water pressure for homes, apartments, small commercial buildings, and irrigation systems. Unlike a standalone pump that requires manual switching, this integrated system includes a self‑priming centrifugal pump, a small pre‑charged pressure tank, a pressure switch, and a pressure gauge – all mounted on a compact baseplate and pre‑wired.

The system senses when a tap is opened, starts the pump automatically, and stops it when the tap is closed. The pressure tank prevents rapid cycling (short‑cycling) and provides a small reserve of pressurised water for immediate use. The result is consistent water pressure, reduced wear on the pump, and no need for user intervention.

This system is ideal for:

  • Homes with low mains water pressure

  • Water supply from rainwater tanks or storage cisterns

  • Shallow wells (up to 8 m suction lift)

  • Small apartments, offices, or shops needing pressure boosting

  • Garden irrigation and greenhouse watering

How the Pressure Booster System Works

The system consists of four core components:

  1. Self‑priming centrifugal pump – Draws water from the source (tank, well, or mains) and pressurises it.

  2. Pressure switch – Senses discharge pressure. Factory set to cut in at 1.5 bar (22 psi) and cut out at 3 bar (43 psi) – adjustable within a range of 1–5 bar.

  3. Small diaphragm pressure tank (2–8 litres) – Cushions pressure spikes, absorbs water hammer, and prevents the pump from starting/stopping too frequently when small amounts of water are used.

  4. Pressure gauge – Allows visual confirmation of system performance.

Operating cycle:

  • With all taps closed, the pump maintains the cut‑out pressure (e.g., 3 bar) and the tank holds pressurised water.

  • When a tap is opened, pressure drops to the cut‑in setting (e.g., 1.5 bar); the pressure switch starts the pump.

  • The pump runs, supplying water while the desired flow is needed.

  • When the tap closes, pressure builds back to cut‑out; the pump stops.

The small tank provides instant water for a few seconds, preventing the pump from starting for every small demand (e.g., filling a glass). This reduces energy consumption and prolongs motor life.

Key Technical Specifications

ParameterRange
Maximum flow3 – 8 m³/h (50 – 135 L/min)
Maximum pressure (head)4 – 6 bar (40 – 60 m) – factory set 3 bar cut‑out
Suction liftUp to 8 m (vertical lift from water surface)
Motor power0.5 – 1.5 HP (0.37 – 1.1 kW)
Voltage / frequency220‑240V / 50Hz or 110‑120V / 60Hz (single‑phase)
Inlet / outlet size1″ × 1″ or 1.25″ × 1″ (25mm or 32mm)
Pressure tank volume2 – 8 litres (pre‑charged diaphragm type)
Pressure switch range1 – 5 bar (factory set 1.5‑3.0 bar)
Liquid temperature0 – 40°C
Enclosure protectionIP44 – IP54 (motor) , IPX2 (control box)
Self‑priming time≤60 seconds (at 5 m lift)
Noise level≤65 dB(A) at 1 metre

Construction Materials

ComponentStandard MaterialUpgrade Option
Pump casingCast iron with epoxy coatingStainless steel 304
ImpellerBrass / engineered plasticStainless steel 304
Diffuser / ejectorBrass / engineered plasticStainless steel
Pressure tankSteel with epoxy coating, butyl diaphragmStainless steel (for drinking water)
ShaftStainless steel (AISI 304)AISI 316
Mechanical sealCarbon / ceramic / NBRSilicon carbide / Viton
FastenersZinc‑plated steelStainless steel

For potable water, all wetted parts are compliant with local drinking water regulations (WRAS, NSF/ANSI 61 available on request).

Standard Features

FeatureBenefit
Automatic start/stopNo manual switching; water on demand
Dry‑run protection (built‑in pressure switch)Pump stops if suction water is lost (pressure falls below 1 bar)
Thermal overload protectionMotor automatically shuts off if overheated; auto‑reset type
Built‑in check valvePrevents backflow when pump stops; keeps system pressurised
Large filter strainerProtects pump from debris (foot valve or suction strainer)
Easy priming portTransparent plug for quick fill and visual check
Corrosion‑resistant coatingEpoxy‑painted casting for outdoor or damp locations
Low noise operationRubber feet and optimised hydraulics reduce vibration
Pressure gaugeShows system pressure at a glance

Applications

ApplicationDescription
Household water pressure boostingIncrease low mains pressure to operate showers, washing machines, and multiple taps simultaneously
Rainwater tank supplyPump rainwater from below‑grade or above‑ground tank to garden, toilet, or laundry
Shallow well supplyDraw from wells up to 8 m deep for domestic use in rural areas
Small apartment / buildingBoost pressure for 2–3 storey buildings with insufficient mains
Garden irrigationRun sprinklers, drip systems, or hose reels effectively
Car wash / workshopProvide pressurised water for cleaning equipment
Rooftop tank fillingMove water from ground tank to overhead tank

Installation Guidelines

  1. Site selection – Place the system on a solid, level, dry surface, protected from rain and direct sun. Ensure adequate ventilation around the motor.

  2. Suction piping – Use rigid pipe (PVC or metal) of at least the pump inlet diameter. Keep the suction pipe short, with minimal elbows. Slope slightly upward to the pump. For well/tank suction, install a foot valve with strainer at the water source.

  3. Discharge piping – Connect to the house or garden distribution system. Install an isolation valve and check valve (if not built‑in).

  4. Electrical connection – Connect to a dedicated circuit with RCD/GFCI protection. Use a weatherproof socket if outdoors. The pump is supplied with a power cord (1–2 m) – extension cables must be of adequate gauge.

  5. Priming – Remove priming plug, fill the pump casing and suction piping completely with water, then replace the plug. Never run the pump dry – even a few seconds will damage the mechanical seal.

  6. Start‑up – Open a tap, plug in the pump. It will prime within 60 seconds and deliver water. If no water after 2 minutes, stop, check suction line for air leaks, and re‑prime.

Pressure Switch Adjustment (If Required)

The pressure switch is factory set to cut in at 1.5 bar and cut out at 3.0 bar – suitable for most homes. To adjust:

  • Increase cut‑in AND cut‑out together – Turn the large nut clockwise.

  • Decrease cut‑in AND cut‑out together – Turn the large nut anticlockwise.

  • Widen differential (increase cut‑out only) – Turn the small nut clockwise (increase cut‑out).

  • Narrow differential (decrease cut‑out only) – Turn the small nut anticlockwise.

Do not set cut‑out above the pump’s maximum pressure rating (stamped on the nameplate). For systems with more than 3–4 fixtures, consider adding a larger external pressure tank.

Energy Efficiency

A pressure booster system with a pressure switch runs only when water is demanded – unlike a continuously running pump. However, the pump operates at full speed whenever it is on. For applications with highly variable flow (e.g., large homes or commercial buildings), a variable frequency drive (VFD) system is more efficient. For most single‑family homes and small buildings, the simple on/off pressure switch system is cost‑effective and reliable.

Maintenance

TaskFrequencyInstructions
Check pressure tank air chargeEvery 6 monthsWith pump off and pressure zero, use a tyre gauge on tank valve. Pre‑charge should be 0.2 bar below cut‑in pressure (e.g., 1.3 bar for 1.5 bar cut‑in). Pump air if needed.
Clean suction strainer / foot valve6‑12 monthsRemove debris from mesh or strainer.
Inspect for leaks (shaft seal, pipe joints)MonthlyLook for drips; replace seal if leaking.
Winterisation (freezing areas)Before freezeDrain pump, tank, and piping completely; store indoors or apply heat trace.
Check pressure switch contactsAnnuallyClean or replace if corroded / pitted.

If the pump cycles rapidly (on/off every few seconds), the pressure tank is likely waterlogged (lost air charge). Re‑pressurise the tank as above; if it fails to hold pressure, the diaphragm is damaged and the tank must be replaced.

Troubleshooting

ProblemLikely CauseSolution
Pump does not startNo power, pressure switch stuck, thermal tripCheck outlet, breaker, plug; press reset button on motor; tap pressure switch
Pump runs but no waterLoss of prime, air leak on suction, foot valve stuckRe‑prime; check suction joints with soapy water; clean foot valve
Pump cycles on/off rapidlyWaterlogged pressure tank, system leak, faulty switchRe‑pressurise tank; repair leaks; replace switch
Low pressure (pump runs continuously)Clogged impeller or strainer, worn pump, low water supplyClean impeller; check suction pipe; verify well/tank level
Motor hums but does not runStuck impeller, bad start capacitor (single‑phase)Turn off power, clear debris from impeller; replace capacitor
Noisy operationCavitation (restricted suction), loose base, worn bearingsCheck suction pipe size; tighten mounting; replace pump if bearings worn

Why Choose Our Pressure Booster System?

  • Plug‑and‑play – Fully assembled, pre‑wired, includes tank and switch – ready to connect to water and power.

  • Automatic convenience – No manual operation; system starts and stops with water demand.

  • Stable pressure – Pressure tank and switch provide consistent supply without severe fluctuations.

  • Self‑priming – Draws water from 8 m below; no foot valve needed (though recommended).

  • Corrosion‑resistant – Epoxy‑coated cast iron or full stainless steel options.

  • Compact design – Fits under a sink, in a utility room, or beside a rainwater tank.

  • Safety built in – Thermal protection, dry‑run shutdown via low‑pressure cut‑off, IP44 motor.

  • Energy efficient – Only runs when water is used; no idle power consumption.

  • Low maintenance – Simple, proven technology with widely available spare parts.

  • 2‑year warranty – Backed by responsive customer support.

Recommended Spare Parts (Per System)

ComponentRecommended Quantity
Mechanical seal kit1 set
Pressure switch (same range)1
Pressure tank (2–8 L)1 (for eventual replacement)
Foot valve with strainer (1″ or 1.25″)1
Start capacitor (for single‑phase motor)1

Get a Quote or Engineering Support

For detailed selection of the correct pressure booster system for your application – including flow and pressure requirements, water source (mains, tank, well), installation conditions, and material preference – please contact our engineering team.

Email: info@hyrig.com

Our engineers support home and small commercial water supply projects worldwide with reliable, automatic pressure booster systems – compact, easy to install, and built for years of trouble‑free service.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit