The Hydrolysis Feed Pump is an API 610 Type BB3 horizontal, axially split, multistage centrifugal pump specifically engineered for feeding process condensate or hydrolyzer feed in urea plant hydrolysis systems. The pump is fully compliant with API 610 11th Edition and ISO 13709 standards, providing reliable, continuous duty in demanding chemical service.
What is a Hydrolysis Feed Pump?
In urea manufacturing, the process condensate produced from evaporation and concentration sections contains residual ammonia, urea, and carbon dioxide. Before disposal or recycle, this condensate is treated in a hydrolysis unit where urea is decomposed back to ammonia and CO2. The hydrolysis feed pump delivers the condensate from storage or collection tank to the hydrolyzer (stripper) operating at elevated temperature (typically 160–200°C) and moderate pressure (1.5–2.5 MPa). The pump handles hot, slightly corrosive process water with traces of ammonia, urea, and carbamate.
Why API 610 BB3 for Hydrolysis Feed?
Multistage head capability — hydrolyzer feed often requires 150–600 m head; BB3 provides this efficiently.
Axially split casing — easy access to internals without disturbing piping, important for regular inspection in urea service.
Corrosion resistance — materials selected for ammonia/urea/water service.
Continuous reliability — API 610 design ensures 3+ years between overhauls.
As a specialized China API 610 pump manufacturer, we produce BB3 pumps tailored to hydrolysis feed and other urea plant auxiliary services.
Primary Media:
Process condensate — water with low concentrations of ammonia (NH₃), urea (CO(NH₂)₂), and CO₂
Hydrolyzer feed — preheated condensate entering hydrolysis column
Treated condensate — after hydrolysis, sent to waste water treatment or recycle
Fluid Characteristics:
Operating temperature: 150–190°C (pump design up to 200°C)
Operating pressure: Suction pressure near atmospheric (from tank); discharge pressure 1.5–2.5 MPa (15–25 bar)
Corrosivity: Mildly corrosive due to ammonia and trace carbamate
Solids: Typically clean but may contain trace precipitates
Toxicity: Low hazard; standard sealing sufficient
Material Selection:
| Component | Recommended Material | Alternative |
|---|---|---|
| Casing | Carbon steel (WCB) or 304SS | 316SS |
| Impellers | 12% Chrome steel or 304SS | 316SS |
| Shaft | AISI 4140 (chrome steel) | 17-4PH SS |
| Wear rings | Hardened 12% Cr | 316SS with Stellite |
| O-rings / Gaskets | EPDM or PTFE | FKM |
For plants requiring higher corrosion resistance (e.g., higher carbamate carryover), upgrade to 316SS or duplex.
Note: Hydrolysis feed is less corrosive than carbamate service. Carbon steel or 304SS wetted parts are generally acceptable for long service life. However, some operators specify 316SS for additional corrosion margin.
Step 1: Define Operating Conditions
| Parameter | Typical Range |
|---|---|
| Flow rate | 10–200 m³/h (depending on plant capacity) |
| Total head | 150–600 m (multistage stages accordingly) |
| Temperature | 150–190°C |
| Suction pressure | Atmospheric or slight positive |
| Discharge pressure | 1.5–2.5 MPa (15–25 bar) |
| NPSH available | Often adequate from tank elevation |
Step 2: Pump Type Selection — BB3 Recommended
| Criteria | BB3 (Axially Split) | OH2 (Single Stage) |
|---|---|---|
| Head capability | Multistage, up to 600 m | Single stage, typically <150 m |
| Suitability for hydrolysis feed | Excellent for moderate to high head | Suitable only for low head |
| Maintenance | Top casing removal | Back pull-out |
For most hydrolysis feed duties (head >150 m), BB3 is the preferred type.
Step 3: Number of Stages
Each stage at 2,950 rpm generates approximately 50–100 m head (depending on impeller design). For 300 m head, 4–6 stages typical.
Use opposed impeller arrangement (back-to-back) for axial thrust self-balancing, eliminating balance drum complexity.
Step 4: Materials
Standard configuration for hydrolysis feed (based on 160°C, clean condensate):
| Component | Standard (Mild) | Upgrade (Corrosive) |
|---|---|---|
| Casing | Carbon steel (WCB) | 304SS or 316SS |
| Impellers | 12% Chrome steel | 304SS / 316SS |
| Shaft | AISI 4140 | 17-4PH SS |
| Wear rings | 12% Cr hardened | 316SS Stellite faced |
| Gaskets | EPDM or PTFE | PTFE |
Step 5: Seal System
For hot water/condensate at 160°C and moderate pressure:
Single mechanical seal with Plan 21 (cooled recirculation) is typical. A heat exchanger cools the flush fluid before entering seal chamber, reducing seal face temperature.
Optional Plan 23 (recirculation with cooler and thermosiphon) for higher temperature reliability.
Plan 11 (uncooled) not recommended above 100°C.
Tandem seal (Plan 52) may be specified for zero emissions or when ammonia content requires additional containment.
Step 6: Bearing Cooling
At 150–190°C process temperature, bearing housing water cooling is recommended. Finned housings may be insufficient; provide water-cooled bearing brackets with temperature control.
Step 7: Auxiliary Features
| Feature | Requirement |
|---|---|
| Centerline mounting | Standard for thermal expansion |
| Water-cooled bearings | Recommended for process >120°C |
| Minimum flow protection | Automatic recirculation valve (ARC) |
| Casing drain and vent | For maintenance and startup |
| Baseplate | Heavy duty steel, epoxy grouted |
| Feature | Benefit for Hydrolysis Service |
|---|---|
| Axially split casing | Upper half removable for full rotor access without disconnecting piping. Simplifies inspection and overhaul in urea plant environment. |
| Multistage diffuser design | Provides required head efficiently; smooth hydraulics reduce vibration. |
| Opposed impeller arrangement | Hydraulically balances axial thrust; no complex balance drum or disk. |
| Between-bearings rotor | Rigid shaft minimizes deflection at elevated temperatures. |
| Centerline mounting | Thermal growth occurs evenly; shaft remains aligned, extending seal life. |
| Renewable wear rings | Replaceable to restore efficiency; hardened surfaces resist galling. |
| API 682 seal chamber | Accepts cooled single seals (Plan 21/23) or tandem seals. |
| Water-cooled bearing housings | Maintains bearing temperature ≤70°C despite 190°C fluid. |
| Heavy duty thrust bearing | Angular contact bearings sized for residual axial load. |
| Parameter | Recommendation |
|---|---|
| Pump Type | API 610 Type BB3 — axially split, multistage, between bearings |
| Flow rate | 10–200 m³/h (as required) |
| Total head | 150–600 m (staged) |
| Speed | 2,950 rpm (50 Hz) / 3,550 rpm (60 Hz) |
| Stages | 3–8 (depending on head) |
| Impeller arrangement | Opposed (back-to-back) |
| Casing material | Carbon steel (WCB) or 304SS |
| Impeller material | 12% Cr steel or 304SS |
| Shaft material | AISI 4140 or 17-4PH SS |
| Flange rating | ASME Class 150 or 300 |
| Mechanical seal | Single, Plan 21 (cooled) or Plan 23 |
| Bearing cooling | Water-cooled housings |
| Lubrication | Oil ring self-lubricating |
| Certification | API 610 11th Edition |
Full API 610 compliance — design, materials, testing per international standards
Proven BB3 technology — widely used in urea plant auxiliary services (hydrolysis feed, condensate transfer, reflux)
Cost-effective — typically 20–30% lower than Western brands
Lead time — 20–28 weeks for carbon steel/304SS configurations
Range of materials — carbon steel, 304/316SS, duplex available
Complete documentation — performance curves, GA drawings, API data sheets
Factory testing — hydraulic performance, mechanical run, vibration monitoring
Spare parts — rings, bushings, seals, bearings stocked
After-sales support — commissioning assistance, training
| Parameter | Specification |
|---|---|
| Pump Type | API 610 Type BB3 — axially split, multistage, between bearings |
| Medium | Process condensate (water, trace NH₃, urea, CO₂) |
| Temperature | Up to 190°C |
| Discharge pressure | 1.5–2.5 MPa (15–25 bar) |
| Flow range | 10–200 m³/h |
| Head range | 150–600 m |
| Casing | Axially split, centerline mounted, carbon steel or 304SS |
| Impellers | Opposed arrangement, 12% Cr or 304SS |
| Seals | Single mechanical seal, Plan 21 (cooled recirculation) |
| Bearing cooling | Water-cooled housings (recommended) |
| Maintenance | Full rotor access without disturbing piping |
For more information or a custom proposal for your hydrolysis feed pump (BB3) application, please contact us at:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.