Overview & Definition
The High Pressure Carbamate Pump is an API 610 Type BB3 horizontal, axially split, multistage centrifugal pump specifically engineered for handling ammonium carbamate (NH₂COONH₄) in urea synthesis high pressure loops. The pump is fully compliant with API 610 11th Edition and ISO 13709 standards.
In urea plants, ammonium carbamate is the intermediate formed from ammonia and carbon dioxide at high temperature (170–210°C) and high pressure (140–250 bar). This pump recirculates carbamate from the carbamate condenser or recovery section back to the urea reactor, operating under extreme corrosion and pressure conditions.
The BB3 configuration features a single axially split casing (split along the horizontal centerline) with multiple impellers arranged in series. This design allows complete access to the rotor assembly by lifting the upper casing half without disturbing suction or discharge piping — a critical maintenance advantage for high pressure, corrosive services.
As a specialized China API 610 pump manufacturer, we produce fully API 610 compliant BB3 pumps for carbamate service, utilizing super duplex stainless steel (25% Cr minimum) for all wetted components to resist the aggressive carbamate corrosion.
Media Compatibility (Ammonium Carbamate)
Primary Media: Ammonium carbamate (NH₂COONH₄) solution in urea synthesis loop.
Fluid Characteristics:
Operating temperature: 170–210°C (pump design range: -60°C to +450°C)
Operating pressure: 140–250 bar (14–25 MPa) — high pressure service
Corrosivity: Extremely corrosive — carbon steel and 316L SS are inadequate
Crystallization tendency: Carbamate solidifies when temperature drops below saturation point
Toxicity: Toxic and corrosive; zero-leakage sealing mandatory
Material Requirement: All wetted components (casing, impellers, diffusers, shaft, wear rings) must be constructed from super duplex stainless steel with minimum 25% chromium content (e.g., SAF 2507 / UNS S32750). Standard 316L is not suitable for high temperature carbamate service.
Elastomers: Use PTFE or FFKM (Kalrez/Chemraz) for O-rings and gaskets. EPDM and Buna‑N are not recommended.
Selection Guidelines for High Pressure Carbamate Pump (BB3)
Step 1: Define Operating Conditions
| Parameter | Typical Range for Carbamate Service |
|---|---|
| Flow rate (Q) | 20–500 m³/h (depends on plant capacity) |
| Total head (H) | 2,000–3,500 m (multistage required) |
| Suction pressure | 140–250 bar (synthesis loop pressure) |
| Discharge pressure | Up to 300 bar |
| Temperature | 170–210°C |
| NPSH available | Often limited; requires low NPSHr design |
Step 2: Select Pump Type — BB3 vs Other Configurations
| Criteria | API 610 BB3 (Axially Split) | API 610 BB5 (Barrel) |
|---|---|---|
| Casing | Single axially split | Double casing (barrel) |
| Pressure rating | Up to ~250 bar | Up to 450+ bar |
| Maintenance | Remove top half, full rotor access | Pull-out cartridge |
| Application | Carbamate recirculation (lower pressure range) | Very high pressure carbamate feed |
| Cost | Lower than BB5 | Higher |
For carbamate services with operating pressures up to 250 bar, BB3 is a proven, cost-effective alternative to BB5. For pressures exceeding 250 bar, BB5 barrel pumps are typically specified.
Step 3: Number of Stages and Speed
Each stage generates approximately 250–400 m head at 2,980–3,600 rpm.
For 3,000 m total head, select 8–12 stages.
Operating speed: 2,980 rpm (50 Hz) or 3,600 rpm (60 Hz) with electric motor drive.
Step 4: Materials — Super Duplex (25% Cr Minimum)
| Component | Material |
|---|---|
| Casing (inner) | Super duplex 25% Cr (SAF 2507 / UNS S32750) |
| Impellers | Super duplex 25% Cr, back‑to‑back arrangement |
| Shaft | Super duplex or Inconel 718 |
| Wear rings | Super duplex with Stellite hard facing |
| Interstage bushings | Tungsten carbide or silicon carbide |
| Casing bolting | A193 B8M Class 2 (316 SS) or super duplex |
| Gaskets / O‑rings | PTFE or FFKM |
Key requirement: Minimum Pitting Resistance Equivalent (PRE) ≥ 40 for all wetted super duplex components. Alloy must be solution annealed and water quenched.
Step 5: Seal System — API 682 Plan 53B
For toxic, corrosive carbamate at high pressure:
Seal type: Double mechanical seal, pressurized (Arrangement 3)
API Plan: Plan 53B — Pressurized barrier fluid reservoir with bladder accumulator
Barrier fluid: Compatible oil or water‑glycol, pressurized 1–3 bar above suction pressure
Seal faces: Tungsten carbide vs. carbon (inner); silicon carbide vs. carbon (outer)
Secondary seals: FFKM (Kalrez / Chemraz)
Zero leakage to atmosphere is mandatory.
Step 6: Auxiliary Systems
| System | Requirement |
|---|---|
| Centerline mounting | Allows thermal expansion at 200°C |
| Bearing cooling | Water‑cooled bearing housings required (>150°C) |
| Minimum flow protection | Automatic recirculation valve (ARC) |
| Bearing temperature monitoring | RTD (PT100) with alarm/trip to DCS |
| Vibration monitoring | Proximity probes per API 670 |
| Casing steam jacketing | Optional — prevents carbamate crystallization |
| Flushing connections | For maintenance purging |
Step 7: NPSH Considerations
Carbamate systems often have limited NPSH available due to high vapour pressure at operating temperature. To improve NPSH performance:
Specify double suction first stage impeller
Increase suction pipe diameter
Elevate suction vessel or lower pump installation
Consider booster pump if NPSHa is critically low
Design Features — BB3 for Carbamate Service
| Feature | Description |
|---|---|
| Axially split casing | Horizontally split along centerline; upper half lifts off for full rotor access without disconnecting piping. |
| Multistage diffuser design | Stationary diffusers between stages provide smooth hydraulics and high efficiency; radial loads are minimized. |
| Opposed impeller arrangement | Impellers arranged back‑to‑back (opposed groups) achieves axial thrust self‑balancing, eliminating complex balance drums. |
| Between‑bearings support | Rotor supported by bearings at both ends for exceptional rigidity and stability under high pressure. |
| Centerline mounting | Casing supported at centerline allows uniform thermal expansion; prevents misalignment at 200°C. |
| Rigid shaft | Large diameter shaft minimizes deflection, extending mechanical seal and wear ring life. |
| Renewable wear parts | Casing rings, impeller rings, interstage bushings are replaceable without replacing major castings. |
| API 682 seal chamber | Accommodates double cartridge mechanical seals with Plan 53B. |
| Water‑cooled bearings | Required for carbamate service above 150°C to maintain bearing temperature ≤70°C. |
API 610 BB3 Carbamate Pump — Typical Specification
| Parameter | Recommendation |
|---|---|
| Pump Type | API 610 Type BB3 — axially split, multistage, between bearings |
| Capacity | 20–500 m³/h (to process) |
| Total head | Up to 3,500 m, staged |
| Speed | 2,980 / 3,600 rpm |
| Stages | 6–12 |
| Impeller arrangement | Opposed (back‑to‑back) |
| Casing material | Super duplex 25% Cr (SAF 2507) |
| Impeller material | Super duplex 25% Cr |
| Shaft material | Super duplex or Inconel 718 |
| Flange rating | ASME Class 1500 / 2500 RF |
| Mechanical seal | Double pressurized (Plan 53B), tungsten carbide vs. carbon |
| Bearing cooling | Water cooled |
| Lubrication | Oil ring (standard) or forced oil |
| Certification | API 610 11th Edition |
Why Choose a China API 610 BB3 Carbamate Pump Manufacturer?
Full API 610 11th Edition compliance — same standards as global brands
Super duplex 25% Cr metallurgy — proven for carbamate corrosion resistance
BB3 axially split design — easy maintenance without disturbing piping
Opposed impeller thrust balancing — eliminates complex balance devices
Complete API 682 seal support systems — Plan 53B skids supplied
Competitive cost — typically 25–35% lower than Western equivalents
Lead time — 30–40 weeks for super duplex configurations
Factory testing — hydraulic performance, mechanical run, NPSH, hydrostatic
Documentation — complete API 610 data package, material certifications
Spare parts — stocked for critical components
After‑sales support — installation, commissioning, training
Summary — High Pressure Carbamate Pump (API 610 BB3)
| Parameter | Specification |
|---|---|
| Pump Type | API 610 Type BB3 — axially split, multistage, between bearings |
| Medium | Ammonium carbamate (NH₂COONH₄) |
| Temperature | Up to 210°C |
| Pressure | Up to 250 bar (suction); up to 300 bar discharge |
| Flow range | 20–500 m³/h |
| Head range | 2,000–3,500 m |
| Casing | Axially split, centerline mounted |
| Impellers | Opposed (back‑to‑back), super duplex |
| Wetted materials | Super duplex 25% Cr minimum |
| Seals | Double mechanical seal, API 682 Plan 53B |
| Bearing cooling | Water cooled (required) |
| Maintenance | Full rotor access without removing piping |
For more information or a custom proposal for your high pressure carbamate pump (BB3) application, please contact us at:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.