The Carbamate Pump is an API 610 Type BB5 horizontal, double casing (barrel type), radially split, multistage centrifugal pump specifically engineered for handling ammonium carbamate (NH₂COONH₄) in high pressure urea synthesis and recirculation services. The pump is fully compliant with API 610 11th Edition and ISO 13709 standards, representing the most critical rotating equipment in the urea production process.
What is a Carbamate Pump?
In urea manufacturing plants, ammonium carbamate is a key intermediate compound formed when ammonia (NH₃) and carbon dioxide (CO₂) react at high temperature (175–225°C) and high pressure (150–250 bar). This highly corrosive intermediate must be efficiently recirculated to the reactor or transferred between process stages. The carbamate pump is the high reliability, mission-critical pump that performs these duties under extreme corrosion, temperature, and pressure conditions.
Carbamate pumps fall into two main categories depending on flow rate and head requirements:
High Pressure Carbamate Feed Pump — delivers carbamate solution from the carbamate condenser or recovery section back to the urea reactor.
Carbamate Recirculation Pump — circulates carbamate within the high pressure loop, often operating at synthesis pressures of 140–250 bar and temperatures of 170–210°C.
Carbamate Solution Transfer Pump — moves carbamate solution between process stages, typically at lower pressures.
Why API 610 for Carbamate Service?
API 610 is the globally recognized standard for centrifugal pumps used in petroleum, petrochemical, and natural gas industries. For carbamate pumps, API 610 compliance ensures:
Extreme corrosion resistance — full compliance with API 610 Table H‑1 material classes, requiring super duplex stainless steel (25% Cr minimum) for all wetted components contacting ammonium carbamate.
High pressure containment — double casing (barrel) design provides the robust pressure containment required for synthesis loop pressures up to 250 bar.
Thermal stability — centerline mounting allows symmetrical thermal expansion at operating temperatures up to 200°C.
Zero leakage containment — API 682 Plan 53B double mechanical seals with pressurized barrier fluid ensure no leakage of corrosive, toxic ammonium carbamate to atmosphere.
High reliability — API 610 BB5 pumps are designed for 3‑5 years continuous operation between overhauls, critical for urea plants where unplanned downtime is extremely costly.
As a specialized China API 610 pump manufacturer, we produce fully API 610 11th Edition compliant carbamate pumps for high pressure urea synthesis service, with proven operational experience in major fertilizer plants worldwide. Our manufacturing capabilities include complete API 610 BB5 design, super duplex and 25% Cr material processing, API 682 seal support systems, and full factory performance testing to API 610 standards.
The Carbamate Pump is specifically engineered for handling the most demanding chemical intermediate in the urea industry:
Primary Media:
Ammonium Carbamate (NH₂COONH₄) — intermediate compound in urea synthesis, formed by reaction of NH₃ and CO₂
Carbamate solution — aqueous solution of ammonium carbamate, typically containing dissolved NH₃ and CO₂
Return carbamate — carbamate recovered from the synthesis loop, often containing urea and other dissolved components
Fluid Characteristics and Engineering Challenges:
| Parameter | Range / Description |
|---|---|
| Operating Temperature | 155–225°C (depending on process stage); pump design range: -60°C to +450°C |
| Operating Pressure | 140–250 bar (14–25 MPa) for reactor feed and recirculation services |
| Pump Discharge Pressure | Up to 300 bar (30 MPa) for high pressure carbamate feed applications |
| Corrosivity | Extremely corrosive — ammonium carbamate causes severe corrosion of standard stainless steels including 316L |
| Material Requirement | 25% Cr minimum super duplex stainless steel or higher alloys for wetted components |
| Crystallization Tendency | Carbamate tends to solidify or crystallize when temperature drops or local concentration increases; requires careful temperature management |
| Density at 200°C | Approximately 850‑950 kg/m³ (varies with composition and temperature) |
| Viscosity | Low (comparable to light hydrocarbon), non‑lubricating — places special demands on bearings and seal faces |
| Vapor Pressure | High at operating temperatures (near saturation); requires positive NPSH margin |
| Toxicity | Ammonium carbamate is toxic and corrosive; zero‑leakage sealing is mandatory, with containment secondary systems |
Material Compatibility — Critical Requirement:
Ammonium carbamate is a strong corrosive medium that attacks conventional stainless steels. The following material compatibility matrix guides selection for carbamate pumps:
| Material | Corrosion Resistance to Carbamate at 200°C | Suitability for Carbamate Service |
|---|---|---|
| Carbon Steel | Not suitable (rapid corrosion) | Never use |
| 304 Stainless Steel | Limited degradation, pitting | Not suitable for high temperature carbamate |
| 316/316L Stainless Steel | Poor — inadequate for high temperature carbamate; corrosion typically >2mm/year after 1000 hours | Not suitable for wetted parts contacting carbamate |
| Duplex 2205 (22% Cr) | Moderate — limited corrosion resistance | Not recommended for extended high temperature service |
| Super Duplex (25% Cr minimum) | Good — preferred material for carbamate service | Recommended for all wetted carbamate components |
| Titanium (TA2/TA10) | Excellent — high corrosion resistance, expensive | Suitable for extreme conditions, special applications |
| Hastelloy C‑276 | Excellent — maximum corrosion resistance | Suitable for extreme conditions where super duplex insufficient |
| Super Austenitic (e.g., 254 SMO) | Good — alternative to super duplex | Acceptable for moderate carbamate conditions |
| Safurex (proprietary) | Excellent — specialized for carbamate | High performance option from some licensors |
Material requirement for API 610 BB5 carbamate pump: For ammonium carbamate service, all wetted components including casing (inner), impellers, diffusers, shaft, and wear rings must be constructed from super duplex stainless steel with minimum 25% chromium content. Super duplex steel is preferred for this service. Standard 316L stainless steel in current use for urea service is widely considered inadequate for severe carbamate corrosion.
Elastomer and gasket selection for carbamate service:
| Material | Compatibility with Carbamate |
|---|---|
| PTFE (Teflon) | Excellent — recommended for static seals and gaskets |
| FFKM (Kalrez / Chemraz) | Excellent — recommended for dynamic seals, O-rings, seal secondary seals |
| FPM (Viton) | Very good — acceptable for moderate conditions but less resistant than FFKM |
| EPDM | Not recommended — reacts with carbamate |
| Buna‑N | Not recommended — degrades rapidly |
| PEEK | Excellent (as backup ring material) |
Fluid Handling Precautions:
Carbamate solution must be maintained above its crystallization temperature throughout the pump and associated piping. Temperature drops below the saturation point cause solid carbamate formation, leading to impeller blockage, seal face damage, wear ring seizure, and potential pump failure.
Oxygen ingress into the carbamate circuit accelerates corrosion rates, requiring inert gas blanketing on storage and seal support systems where applicable.
The carbamate circuit must be purged before pump maintenance to remove residual carbamate, as exposure to atmosphere may cause rapid corrosion of exposed ferrous components and present safety hazards.
Selecting the correct carbamate pump requires systematic evaluation of process conditions, fluid properties, and plant requirements, with particular attention to corrosion resistance, pressure containment, and NPSH available.
Step 1: Define Process Conditions — Essential Data
Accurate operating data is critical for proper carbamate pump selection. Key parameters needed:
| Parameter | Required Information |
|---|---|
| Flow rate (Q) | Rated flow, normal flow, minimum continuous flow |
| Total head (H) | Discharge pressure requirement; typical: 2,500–3,500 m head for high pressure carbamate feed |
| Operating temperature | 155–225°C typical; required range (minimum, normal, maximum) |
| Carbamate composition | Concentration, NH₃/CO₂ ratio, presence of urea, water content |
| Vapor pressure | At operating temperature — determines NPSHa margin |
| Suction pressure | Available at pump inlet; carbamate pumps often require positive suction head |
| NPSH available (NPSHa) | Critical parameter for centrifugal selection; carbamate systems often have limited NPSHa |
| Specific gravity | Density at operating temperature |
| Viscosity | At operating temperature (typically low) |
| Solids content | Crystallization potential; carbamate may contain solid deposits |
Step 2: Select Pump Type — Carbamate Pump Configuration
Based on flow rate, head requirement, and installation constraints, carbamate pumps can be either centrifugal (API 610) or positive displacement (reciprocating) designs. Both types have been used in carbamate service for over 30–35 years:
| Criteria | API 610 Centrifugal BB5 | Reciprocating (Positive Displacement) |
|---|---|---|
| Typical Flow Range | 20–500 m³/h | 5–150 m³/h |
| Typical Head Range | 2,000–4,000 m | Up to 4,000 m |
| Pressure Generation | Multistage impellers | Piston/plunger displacement |
| Maintenance Frequency | Lower — 3‑5 years between major overhauls | Higher — more frequent packing/valve replacement |
| Pulsation | None — smooth, continuous flow | High pulsation requires pulsation dampeners |
| NPSH Sensitivity | Requires careful NPSH margin | Less sensitive to NPSH, can handle suction lifts |
| Space Requirements | Larger footprint | Moderate footprint |
| Cost (Capital) | Higher initial for high alloy construction | Moderate |
| Operating Cost | Lower — fewer wearing parts | Higher — regular packing/valve replacement |
| Preferred Application | New plants, large flow continuous operation | Small plants, retrofit, facilities requiring variable flow |
Selection recommendation: For most modern large‑scale urea plants (daily production >1,000 MT), the API 610 BB5 centrifugal carbamate pump is the preferred choice, offering reliable, smooth, low‑maintenance high pressure operation. For smaller plants (daily production <500 MT) or facilities with variable flow demands, reciprocating carbamate pumps may be more appropriate.
Step 3: Select Pump Configuration — BB5 Design Features
For centrifugal carbamate pumps, the API 610 BB5 double casing barrel pump is the standard industry configuration:
Double casing (barrel) construction — outer forged steel barrel provides primary pressure containment; inner radially split diffuser casing houses impellers.
Multistage impeller arrangement — 5 to 12 stages arranged to generate required total head; opposed (back‑to‑back) impeller arrangement for axial thrust self‑balancing.
Between‑bearings support — shaft supported by bearings at both ends for exceptional rigidity and stability under high hydraulic loads.
Centerline mounting — allows uniform thermal expansion.
Technical comparison of BB5 barrel pump parameter ranges:
| Manufacturer | Model | Flow (m³/h) | Head (m) | Pressure (bar) | Temp (°C) | Features |
|---|---|---|---|---|---|---|
| Ruhrpumpen | A-Line Barrel | Up to 1,400 | Up to 4,200 | Up to 450 | Up to +450 | API 610 BB5, diffuser type |
| Changzhi | CP-BB5 | 20–800 | Up to 3,200 | Up to 420 | -80 to +450 | Double casing, back‑to‑back impellers |
| Volm | VMB05 | 25–1,200 | Up to 3,200 | 150/260/350 | -80 to +450 | API 610 BB5, multistage |
| Huasheng | BB5 | 20–1,000 | Up to 3,500 | Up to 300 | Up to +260 | API 610 BB5 |
| Hunan Tianyi | TDC | Within API 610 | Within API 610 | Up to 300 | -80 to +450 | Radial split barrel |
Step 4: Select Number of Stages and Speed
The required total head determines the number of impeller stages. Each stage typically generates 250–400 m head at 3,600 rpm. A carbamate pump requiring 3,000 m total head would therefore need 8–12 stages.
Available operating speeds for BB5 pumps range from 1,450 to 3,600 rpm (50/60 Hz) for conventional motor drives. For higher speeds (4,000–8,000 rpm), integrally geared (OH6) designs may be considered, though BB5 remains preferred for most carbamate services.
Step 5: Select Materials — Super Duplex (25% Cr Minimum)
For carbamate service, material selection is the most critical aspect of pump specification. The following super duplex material matrix provides guidance:
| Component | Required Material (Carbamate Service) | Alternative Option |
|---|---|---|
| Outer barrel (pressure containment) | Forged carbon steel (WCB / A216), fully radiographed | Forged 316L SS (for higher corrosion allowance) |
| Inner casing (diffuser) | Super duplex stainless steel (25% Cr) | Duplex 2205 (for less severe carbamate conditions) |
| Impellers | Super duplex stainless steel (25% Cr) — back‑to‑back arrangement | Duplex 2205 (limited service) |
| Shaft | Super duplex stainless steel or SAF 2507 | Inconel 718 for extreme conditions |
| Wear rings (casing) | Super duplex with hard facing (tungsten carbide or Stellite) | — |
| Wear rings (impeller) | Super duplex with hard facing (tungsten carbide or Stellite) | — |
| Interstage bushings | Silicon carbide (SC) or tungsten carbide (TC) — full set | Carbon / PTFE composite |
| Throttle bushings | Super duplex with hard facing | Silicon carbide |
| Fasteners — internal | A193 B8M Class 2 (316 SS) or UNS S32760 super duplex | Hastelloy C‑276 |
| Fasteners — external | A193 B7M or B16, with anti‑seize coating | B8M Class 2 with PTFE coating |
| Gaskets (face, O‑rings) | PTFE envelope gasket or spiral wound with PTFE filler | FFKM (Kalrez) for dynamic applications |
Key material specifications for super duplex: Minimum Pitting Resistance Equivalent (PRE) ≥40 required for reliable carbamate service. SAF 2507 (UNS S32750) and 25% Cr super duplex alloys meet this requirement. All super duplex components require solution annealing and water quenching after fabrication to maintain corrosion resistance.
Step 6: Design for Thermal Stability and Temperature Management
Carbamate pumps must be designed with careful attention to thermal growth, given the operating temperature range from cold commissioning to normal 200°C operation:
Centerline mounting — the pump casing is supported at the horizontal centerline, allowing symmetrical thermal expansion and preventing misalignment. Barrel pumps are typically supported by pedestals mounted at the centerline plane.
Bearing housing cooling — for carbamate services above 150°C, water‑cooled bearing housings are required to maintain bearing temperatures within safe operating limits (≤70°C). Cooling water flow regulated by flow control valves.
Warm‑up and cooldown procedures — the pump must be warmed up gradually before start (typically 30–50°C per hour temperature ramp) to avoid thermal shock and differential expansion that could cause internal rubbing. Cool down rates similarly controlled after shutdown.
Thermal sleeve on motor shaft — when pump operates at elevated temperature, a thermal sleeve or extended spacer coupling separates the pump shaft from motor shaft to prevent heat transfer from pump to motor bearings.
Step 7: Specify Seal System — API 682 Plan 53B
For carbamate service (toxic, corrosive, high pressure), seal selection is critical for environmental and personnel safety. The recommended seal configuration is:
Type: Double mechanical seal (pressurized) — two seal faces arranged back‑to‑back with a pressurized barrier fluid between them.
Arrangement: Arrangement 3 — tandem arrangement but with pressurized barrier fluid ensuring zero process leakage to atmosphere.
API 682 Plan: Plan 53B — Pressurized barrier fluid reservoir with bladder accumulator. The barrier fluid (typically compatible oil or water‑glycol mixture) is pressurized to 1–3 bar above pump suction pressure, ensuring any leakage path across the inner seal is from barrier fluid into process, not the reverse. No ammonia or carbamate escapes to atmosphere.
Seal faces: Inner seal — tungsten carbide vs. carbon (for low lubricity carbamate). Outer seal — silicon carbide vs. carbon.
Secondary seals: FFKM (Kalrez / Chemraz) for chemical compatibility with carbamate and barrier fluid.
Reservoir monitoring: The Plan 53B reservoir includes pressure gauge, level transmitter (low level alarm indicates potential inner seal leakage), temperature transmitter, and a nitrogen supply connection for pressurization.
For severe carbamate corrosion conditions, some licensees and plant operators specify Plan 54 — an active external barrier fluid circulation system including pumps, filters, coolers, and accumulators.
Plan 53B reservoir and seal support system should be constructed from stainless steel for corrosion resistance. Complete API 682 seal support documentation required.
Step 8: Specify Monitoring Systems
For carbamate service, comprehensive instrumentation is required to ensure safe, reliable operation:
| Monitoring System | Specification |
|---|---|
| Bearing temperature | RTD probes (PT100) in both drive‑end and non‑drive‑end bearing housings; local indication and 4–20 mA signal to DCS; alarm at 85°C; trip at 95°C |
| Vibration monitoring | Proximity probes (eddy current) for shaft vibration measurement (displacement) per API 670; accelerometers for bearing housing vibration (velocity) |
| Suction pressure | Chemical seal diaphragm gauge with 4–20 mA transmitter to DCS; low suction pressure interlock protects against NPSH violation |
| Discharge pressure | Pressure transmitter with high limit alarm to DCS |
| Seal support system monitoring | Plan 53B: reservoir level transmitter, pressure transmitter, temperature transmitter, pressure indicator, nitrogen supply pressure regulator |
| Process temperature | Thermowell‑mounted temperature transmitter on pump suction and discharge nozzles |
| Local display | Local control panel with all instrument readings, push buttons, status lights, and emergency stop push button |
| Baseplate condition monitoring provisions | Provisions for mounting accelerometers and thermocouples at prescribed locations per API 610 requirements |
Step 9: Consider Auxiliary Systems
| Auxiliary System | Requirements for Carbamate Service |
|---|---|
| Minimum flow recirculation | Automatic recirculation valve (ARC) or control valve + orifice required to ensure pump never operates below minimum continuous stable flow. Min flow line should return to carbamate condenser or storage tank. |
| Bearing cooling water | Treated cooling water (closed loop) at 5–10 bar, 25°C inlet, regulated by flow control valve and temperature control valve |
| Barrel drain connections | Low point drains at barrel bottom with double isolation valves for purging and maintenance |
| Casing vent connections | High point vents at barrel top for startup air removal, with vent line to flare or scrubber |
| Flushing connections | Connections on casing and seal chamber for solvent flushing during maintenance |
| Barrier fluid system (Plan 53B) | Complete skid mounted reservoir, bladder accumulator, pressure transmitter, level transmitter, nitrogen panel, associated instrumentation and controls |
| Baseplate | Heavy duty fabricated steel baseplate, epoxy grouted, with drip rim and oil collection sump |
Step 10: Perform NPSH Analysis
NPSH available (NPSHa): Calculate based on suction side conditions (pressure, temperature, elevation). Carbamate systems may have limited NPSHa due to high operating temperatures and high vapour pressure.
NPSH required (NPSHr): The pump manufacturer provides NPSHr curves derived from cavitation testing per API 610. For centrifugal multistage BB5 carbamate pumps, typical NPSHr is 4–12 m depending on flow and speed.
NPSH margin: Maintain NPSHa ≥ NPSHr + 2 m margin to ensure cavitation‑free operation. If NPSHa is marginal, consider:
Lowering pump installation elevation relative to suction source
Increasing suction pipe diameter
Adding a booster pump in series
Selecting a pump with specially designed low‑NPSH first stage impeller (double suction configuration)
Using a positive displacement pump (if all else fails) which is less sensitive to NPSH than centrifugal
The following application matrix guides carbamate pump selection based on specific process requirements:
| Process Requirement | Recommended Pump Type | Justification |
|---|---|---|
| Large urea plant (>1,500 MT/day), continuous operation, high flow (50–400 m³/h) | API 610 BB5 centrifugal (multistage barrel pump) | Smooth flow, low maintenance, high efficiency, proven reliability |
| Small urea plant (<500 MT/day), low flow (10–60 m³/h) | Reciprocating (plunger) pump | Lower capital cost, simpler control, better suited for low flow |
| Plant with difficult suction conditions, limited NPSHa | Reciprocating pump | Less sensitive to cavitation than centrifugal |
| Retrofit / replacement of existing PD carbamate pump | Reciprocating replacement (same type) | Minimal piping and foundation modifications |
| New urea plant where high reliability and low maintenance are priorities | API 610 BB5 centrifugal | 3‑5 years between overhauls; proven in modern urea plants |
| Plant with high variable flow requirements (e.g., flexible production load 50–100% of capacity) | Reciprocating with VFD or centrifugal with VFD | Both can handle turndown; centrifugal VFD may be more efficient across range |
| High head requirement >3,500 m (e.g., additional synthesis loop elevation) | Centrifugal BB5 (12+ stages) or reciprocating | Both can achieve required head; selection based on other factors |
For the majority of modern large‑scale urea plants, the API 610 BB5 centrifugal carbamate pump is the preferred selection. These pumps are designed for the most demanding petrochemical applications.
As a specialized China API 610 BB5 pump manufacturer, we provide full compliance with API 610 11th Edition (ISO 13709) including:
Design Verification:
Hydraulic design using CFD (computational fluid dynamics)
Rotordynamics analysis per API 610 Annex K
Critical speed analysis and separation margins for lateral and torsional critical speeds
Finite element analysis (FEA) of barrel and casing components
Materials Verification:
Material certifications to EN 10204 3.1 or 3.2
Positive Material Identification (PMI) of all wetted components (super duplex, 25% Cr)
Hardness testing for all super duplex components
Intergranular corrosion testing per ASTM A262 Practice E for super duplex
Impact testing at minimum design temperature per ASME Section VIII
Manufacturing:
Barrel casing: forged steel, fully radiographed and magnetic particle inspected
Inner casing and diffusers: investment cast or machined from super duplex billet; solution annealed and water quenched
Impellers: 5‑axis CNC machined from super duplex forging or casting; dynamically balanced to ISO 1940 Grade G2.5
Shaft: precision ground super duplex material with surface finish Ra ≤ 0.8 μm
Testing:
Hydrostatic pressure test of barrel casing: 1.5 × design pressure for 30 minutes minimum
Hydraulic performance testing: Q‑H, efficiency, NPSH3 determination on certified test loop
Mechanical run test: 4 hours minimum at rated speed; vibration monitoring per API 610
Oil system functional test (where forced lubrication specified)
Seal support system functional test with Plan 53B simulation
Noise level measurement per API 610
| Parameter | Recommendation |
|---|---|
| Pump Model | API 610 Type BB5 — Horizontal, double casing (barrel), radially split, multistage, between bearings |
| Capacity (Q) | 20‑500 m³/h (selected to process requirements) |
| Total Head (H) | Up to 3,500 m, staged to meet system requirements |
| Speed (rated) | 2,980 rpm (50 Hz); 3,600 rpm (60 Hz) |
| Impeller Arrangement | Opposed (back‑to‑back) for axial thrust balancing |
| Number of Stages | 5‑12 (dependent on total head) |
| Casing Material | Inner: Super duplex 25% Cr (e.g., SAF 2507 / UNS S32750); Outer: Forged carbon steel (A216 WCB) |
| Impeller Material | Super duplex 25% Cr (cast or machined) |
| Shaft Material | Super duplex or Inconel 718 |
| Wear Rings | Super duplex with Stellite 6 hard facing (or CRN spray coating) |
| Interstage Bushings | Tungsten carbide or silicon carbide |
| Flange Rating | ASME Class 1500 or Class 2500 RF |
| Flange Orientation | Top‑Top (standard) |
| Mechanical Seal | Double mechanical seal, pressurized (Arrangement 3), API 682 Plan 53B with bladder accumulator and reservoir; Seal faces: tungsten carbide vs. carbon (primary) / silicon carbide vs. carbon (secondary) |
| Barrier Fluid | Compatible oil or water‑glycol mixture, pressurized 1‑3 bar above suction pressure |
| Bearing Type | Radial: Cylindrical roller bearings; Thrust: Angular contact pairs or tilting pad thrust bearings |
| Lubrication | Oil ring self‑lubricating (standard) or forced oil circulation (high power applications) |
| Bearing Cooling | Water‑cooled bearing housings (required for carbamate service >150°C) |
| Baseplate | Heavy duty steel baseplate, epoxy grouted, to 2× API 610 nozzle loads |
| Coupling | Flexible spacer coupling, 6700 series, with coupling guard complying with API 610 requirements (zero‑speed interlock provision) |
| Minimum Flow Protection | Automatic recirculation valve (ARC) |
| Certification | API 610 11th Edition, ISO 13709, NACE MR0175 / MR0103 (as required) |
As a specialized China API 610 BB5 pump manufacturer with extensive experience in urea plant carbamate pumps, we deliver:
Full API 610 11th Edition (ISO 13709) compliance — designed, manufactured, and tested to the same rigorous standards as leading global brands
Super duplex (25% Cr minimum) metallurgy capability — proven experience with SAF 2507, UNS S32760, and other high alloy materials for carbamate service
Proven BB5 barrel pump technology — used in carbamate recirculation, ammonia feed, and other high pressure services in major fertilizer plants
Complete API 682 seal support systems — Plan 53B reservoir skids, barrier fluid selection, and full documentation
Shorter lead times — 30‑40 weeks ARO for standard super duplex configurations
Competitive capital cost — typically 25‑35% lower than major Western brands for equivalent API 610 BB5 configurations
Complete documentation package — hydraulic performance curves, NPSH curves, sectional drawings, GA drawings, API 610 data sheets, material certifications, rotordynamics analysis, and installation/maintenance manuals
Factory performance testing — witnessed and non‑witnessed options; testing includes hydraulic performance, mechanical run, vibration and bearing temperature monitoring, and hydrostatic testing on high pressure loop
Third‑party inspection — acceptance to customer specification (e.g., Lloyds, DNV, BV, TÜV) available
Global shipping and export packaging — wooden crates, VCI, desiccant, and full export documentation
Spare parts availability — critical spares (mechanical seals, bearings, interstage bushings, wear rings) stocked; complete spare parts kits available for scheduled overhauls
Installation and commissioning support — on‑site supervision, training, and after‑sales service
Warranty — 18 months from dispatch or 12 months from commissioning, whichever occurs first
| Parameter | Specification |
|---|---|
| Pump Type | API 610 Type BB5 — horizontal, double casing (barrel), radially split, multistage, between bearings |
| Medium | Ammonium carbamate (NH₂COONH₄) — urea synthesis intermediate |
| Operating Temperature | Up to 225°C (design range -60°C to +450°C) |
| Operating Pressure | Up to 250 bar (synthesis loop) / up to 300 bar discharge |
| Typical Flow Range | 20–500 m³/h |
| Typical Head Range | 2,000–4,000 m |
| Casing Construction | Double casing: outer forged steel barrel + inner radially split diffuser casing |
| Impeller Arrangement | Back‑to‑back (opposed) for axial thrust self‑balancing |
| Number of Stages | 5–12 (selected to total head requirement) |
| Wetted Materials (Minimum) | Super duplex stainless steel, 25% Cr (Full API 610 Table H‑1 compliance) |
| Seals | Double mechanical seal, pressurized barrier fluid, API 682 Plan 53B |
| Seal Faces | Tungsten carbide vs. carbon (primary) |
| Secondary Seals | FFKM (Kalrez / Chemraz) |
| Lubrication | Oil ring self‑lubricating / forced oil circulation (high power) |
| Bearing Cooling | Water‑cooled bearing housings required for carbamate service |
| Certification | API 610 11th Edition, ISO 13709, NACE (on request) |
| Maintenance | 3‑5 years continuous operation between overhauls |
For more information or a custom engineering proposal for your carbamate pump (ammonium carbamate service in urea plant) application, please contact us at:
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.