Urea Melt Pump (Molten Urea Transfer) | API 610 VS4 Vertical Sump Pump China Manufacturer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 VS4 vertical long shaft centrifugal pump for molten urea melt transfer service in urea prilling and granulation. Medium: molten urea (120–150°C). Heating jacket prevents urea crystallization. Single stage volute design with open impeller, submerged operation eliminates priming. Manufactured in China with API 610 11th Edition compliance. Suitable for urea melt pits, sumps, storage tanks and urea prilling tower feed.

Conatct For Details
DetailReview(0)Additional

Overview & Definition

The Urea Melt Pump is an API 610 Type VS4 vertical, single casing, volute type, long shaft centrifugal pump specifically engineered for handling molten urea (urea melt) in fertilizer plants, urea prilling towers, and granulation units. The pump is fully compliant with API 610 11th Edition and ISO 13709 standards.

What is a Urea Melt Pump?

In urea manufacturing, after concentration in evaporators (typically 95–99.7% urea concentration), the molten urea must be transferred from the melt pit, sump, or storage tank to the prilling tower or granulation unit where it solidifies into final product prills or granules. The urea melt pump handles this high temperature, crystallization-prone fluid, operating at approximately 120–150°C. Urea melt has a crystallization temperature around 132°C, so the pump must maintain fluid temperature above this point to prevent solidification within the pump casing, seal chamber, or column pipe.

Why API 610 VS4 for Urea Melt Service?

VS4 pumps are vertically suspended, single casing, volute type pumps with a long shaft driving a submerged impeller at the bottom. For urea melt service, VS4 offers distinct advantages:

  • Submerged operation — The impeller and lower casing are submerged below the minimum liquid level in the melt pit or sump, providing excellent suction conditions and eliminating priming requirements. No Net Positive Suction Head available issues.

  • Heating jacket capability — The pump can be fitted with steam heating jackets on the casing, column pipe, and discharge head to maintain urea melt temperature above crystallization point, preventing solidification when the pump is idle.

  • No shaft seal leakage — In VS4 configuration, the shaft passes through the column pipe with liquid level below the discharge head; there is no pressurized shaft seal at the bottom because the impeller is submerged. The wetted shaft section runs inside the column pipe, eliminating seal leakage concerns on molten urea.

  • Long shaft for deep sump — Vertical design allows installation in deep melt pits (typically 3–10 meters deep) with the motor located above at grade level, protecting motor from heat.

As a specialized China API 610 pump manufacturer, we produce fully API 610 11th Edition compliant VS4 urea melt pumps for fertilizer plants worldwide, with proven performance in prilling tower feed and granulation service.

Media Compatibility (Molten Urea / Urea Melt)

The Urea Melt Pump is specifically engineered for handling molten urea and similar high temperature, crystallization-prone media:

Primary Media:

  • Molten urea (urea melt) — concentrated urea solution (typically 95–99.7% urea, remainder water)

  • Urea prilling feed — molten urea pumped to prilling tower spray heads

  • Urea granulation feed — molten urea pumped to granulation drum or fluid bed granulators

  • Molten urea melt sump transfer — from evaporators to storage or prilling tower

Fluid Characteristics and Engineering Challenges:

ParameterRange / Description
Operating Temperature120–150°C typical; pump design range -20°C to +180°C
Urea Concentration95–99.7% (balance water)
Crystallization TemperatureApproximately 132°C (depends on concentration)
ViscosityLow (similar to water at elevated temperature)
CorrosivityMildly corrosive; requires stainless steel construction
Crystallization RiskHigh — temperature drops below crystallization point cause solid urea deposition in pump casing, on impeller, and in column pipe, leading to seizure and pump failure
Vapor PressureLow at operating temperature
DensityApproximately 1.1–1.2 g/cm³ depending on temperature and concentration

Fluid Handling Precautions:

  • Maintain urea melt temperature ≥5°C above crystallization point throughout the pumping system

  • Heat tracing on suction piping and discharge piping

  • Pump casing heating jacket with steam (≤0.6 MPa, up to 170°C) or electric trace heating

  • Keep the pump in standby mode with circulation or heating to prevent solidification when idle

  • Avoid dead legs and stagnant zones where urea can cool and solidify

Material Selection for Urea Melt Service:

ComponentRecommended MaterialUpgrade Option
Casing (Volute)304SS or 316SS316L SS
Impeller304SS or 316SS (open or closed)316L SS / Duplex 2205
Shaft17-4PH SS or AISI 4140 with SS sleeveStainless Steel
Column Pipe304SS or 316SS316L SS
Discharge HeadCast iron or Carbon steel with insulation304SS
Guide Bearings (submerged)PTFE-lined bronze or Silicon carbideCarbon / PTFE composite
FastenersA193 B8M (316 SS)—
Gaskets / O-ringsPTFE or EPDMFFKM

Material rationale: 304SS or 316SS provides adequate corrosion resistance for pure urea melt service. For urea with impurities or higher corrosivity, upgrade to 316L SS or duplex.

Design Features — VS4 for Urea Melt Service

The API 610 VS4 urea melt pump incorporates design features specifically addressing the challenges of high temperature, crystallization-prone urea melt transfer:

FeatureDescription and Benefit for Urea Melt Service
Vertically suspended, long shaft designPump is mounted vertically with motor at grade level and impeller submerged in melt pit or sump. Accessible for maintenance without pit entry. Long shaft lengths up to 10 m available.
Single casing volute designSingle stage volute casing at the bottom, submerged. Volute collects discharge and directs into column pipe. Double volute construction for diameters above 80 mm balances radial loads and reduces shaft deflection.
Steam heating jacketCasing, column pipe, and discharge head fitted with integral or external steam jackets. Low pressure steam (≤0.6 MPa, up to 170°C) circulates through jackets, maintaining urea melt temperature above 132°C crystallization point. Essential for preventing solidification when pump is idle or during cold startup.
Open impeller (or enclosed)Open impeller design (standard for urea melt) handles potential solid deposits and minimizes risk of binding if minor crystallization occurs. Enclosed impeller optional for higher efficiency when fluid is clean.
No submerged shaft sealImpeller is submerged, so there is no pressurized mechanical seal at the bottom. Shaft passes through column pipe inside the liquid; seal is located at the top (discharge head) for column pipe above liquid level, or eliminated entirely. Eliminates leakage risk from molten urea at high temperature.
Single or multi-stage configurationSingle stage for most urea melt applications. Multistage (additional bowls) available where higher head is required.
Rigid long shaft with intermediate guide bearingsShaft supported by rolling bearings in bearing housing (above grade) and intermediate guide bearings (plain bearings) inside column pipe. Guide bearing spacing per API 610 to maintain critical speed separation and reduce vibration.
Guide bearing lubricationWater or process fluid lubrication (self-flushed) for submerged guide bearings. External flush connection optional for high temperature or dirty service.
Thrust bearing assemblyHeavy duty thrust bearing (angular contact) in discharge head supports weight of the shaft and impeller assembly, plus hydraulic axial thrust. Oil or grease lubricated.
Discharge column with flanged connectionsSeparate discharge column pipe with flanged sections for easy assembly, disassembly, and maintenance. Discharge flange located on discharge head at top, horizontal or vertical orientation.
Flexible coupling with motorSpacer coupling between motor and pump shaft allows removal of motor without disturbing column pipe or discharge head during maintenance.
API 682 seal at top (optional)When column pipe is not sealed (vented to atmosphere), no top seal is required. For pressurized column or emissions control, API 682 single mechanical seal at discharge head with Plan 11 flush.
Materials304SS or 316SS for all wetted components. Carbon steel for non-wetted structural parts.
Baseplate / Mounting flangeHeavy duty mounting flange bolted to concrete pit cover or support structure. Motor mount on discharge head or separate baseplate.

Selection Guidelines for Urea Melt Pump (VS4)

Selecting the correct urea melt pump requires systematic evaluation of process conditions, fluid properties, and installation requirements:

Step 1: Define Operating Conditions

ParameterTypical Range for Urea Melt ServiceRequired Information
Flow rate (Q)10–400 m³/h (prilling tower feed)Rated, normal, and minimum flow
Total head (H)50–180 m (depending on tower height)Discharge pressure required
Operating temperature135–150°C (melt temperature)Minimum, normal, maximum
Urea concentration95–99.7%Water content impacts crystallization temperature
ViscosityLow (similar to water)At operating temperature
Specific gravity1.1–1.2 at 140°CAt operating temperature
Suction conditionMelt pit or sumpPit depth, minimum liquid level
Solids contentClean (no solids)Must be essentially particle-free; open impeller tolerates minor deposits

Step 2: Determine Head and Flow Requirements

Urea melt pumps typically serve prilling towers requiring 50–120 m head for top-fed towers, or 100–180 m head for taller towers or remote granulation units. Flow depends on plant capacity:

  • 500 t/day urea plant: 20–30 m³/h typical

  • 1,000 t/day urea plant: 40–60 m³/h

  • 2,000 t/day urea plant: 80–100 m³/h

  • 3,000+ t/day: 120–200 m³/h

Step 3: Determine Sump Depth and Shaft Length

Measure required length from pump mounting flange (at grade level) to the impeller suction bell. Standard shaft lengths available from 3 to 10 meters. Longer shafts require additional guide bearings and careful shaft alignment.

Step 4: Select Impeller Type

Impeller TypeSuitability for Urea Melt
Open impellerRecommended — handles minor deposits from crystallization to prevent binding; easier cleaning if solidification occurs; lower efficiency but more reliable in service
Closed (enclosed) impellerOptional for high efficiency when fluid is guaranteed clean; higher first cost; more susceptible to damage if urea solidifies
Double suction impellerNot required for urea melt (NPSH is not an issue due to flooded suction)

Step 5: Select Materials

ComponentStandard MaterialUpgrade Option
Volute casing304SS cast316SS / 316L SS
Impeller304SS (open, cast)316SS / 316L SS
Shaft17-4PH SS (hardened)316SS (for corrosion)
Column pipe304SS (seamless or welded)316SS
Discharge headCarbon steel (insulated)304SS
Guide bearings (submerged)PTFE-lined bronzeSilicon carbide / Carbon
Thrust bearings (top)Angular contact steel bearings (oil/grease)—
GasketsPTFE or EPDMFFKM

316SS recommended for complete urea melt service due to better corrosion resistance than 304SS when urea contains trace impurities or when operating near upper temperature limit.

Step 6: Specify Heating Jacket Requirements

ComponentHeating Jacket Requirement
Volute casingRequired — integral steam jacket with 0.3–0.6 MPa steam at 150–170°C
Column pipeRequired (especially for longer pipes) — external steam jacket or heat tracing
Discharge headOptional (insulation may suffice)
Suction pipingHeat tracing on external piping (not part of pump)

Steam jacket specifications:

  • Design pressure: up to 1.0 MPa

  • Steam conditions: ≤0.6 MPa, ≤170°C

  • Jacket connections: 1/2" or 3/4" NPT female connections (supplied on casing and column)

Step 7: Specify Seal System

For VS4 urea melt pumps with top mechanical seal:

ConfigurationRecommendation
Column pipeOpen (vented) — no top seal required
Pressurized columnSingle mechanical seal (API 682 Type A)
Seal flush planPlan 11 (internal recirculation + orifice) with heating to prevent crystallization in flush line
Seal facesSilicon carbide vs. carbon
Secondary sealsEPDM or PTFE (compatible with urea)
QuenchNot required

Step 8: Specify Auxiliary Features

  • Bearing cooling: Water cooled bearing housing recommended for continuous operation >80°C ambient + process heat transmitted up shaft.

  • Guide bearing flushing: External water flush for submerged guide bearings when pump is operating in dirty service. Self-flushing (process fluid) acceptable for clean urea melt.

  • Casing drain: Low point drain for emptying pit or sump before maintenance.

  • Column vent: High point vent for startup air removal.

  • Insulation: Thermal insulation on discharge head and exposed piping.

  • Coupling guard: Removable aluminum or stainless steel guard with lockout provisions.

Step 9: Consider Redundancy

Urea melt pumps are critical for continuous plant operation. Recommended configurations:

  • Duty/Standby arrangement — Two pumps installed in parallel, one operating, one standby with steam heating jackets active to keep pump warm and ready for immediate startup

  • Spare parts kit — Complete set of wear parts: impeller, shaft, guide bearings, gaskets, fasteners

Typical Specifications — API 610 VS4 Urea Melt Pump

ParameterRecommendation
Pump TypeAPI 610 Type VS4 — Vertical, single casing, volute, long shaft sump pump
MediumMolten urea (urea melt), 95–99.7% concentration
Operating temperature135–150°C (Design range -20°C to +180°C)
Design pressure (casing)Up to 1.6 MPa
Flow range2–400 m³/h (selected to plant capacity)
Head rangeUp to 180 m
Speed2,950 rpm (50 Hz) / 3,550 rpm (60 Hz)
CasingSingle stage volute (double volute for sizes >DN80)
ImpellerOpen type (recommended) / closed (optional)
Impeller material304SS / 316SS
Casing material304SS / 316SS cast
Column pipe material304SS / 316SS seamless
Shaft material17-4PH SS (hardened) or 316SS
Guide bearings (submerged)PTFE-lined bronze (flooded)
Mounting flangeCarbon steel or stainless steel fabricated
Steam jacketIntegral on casing and column pipe, ≤0.6 MPa steam
Shaft lengthStandard to 10 m (custom available)
Bearing coolingWater-cooled housing (recommended)
Bearing lubricationOil or grease lubricated
CouplingSpacer type, with guard
CertificationAPI 610 11th Edition (ISO 13709)

Manufacturers — API 610 VS4 Urea Melt Pumps (China)

Several specialized China API 610 manufacturers offer VS4 pumps suitable for urea melt service:

Anhui Huasheng Pumps & Valves

  • VS4 vertically suspended, cantilever sump pumps with discharge through column

  • Flow to 800 m³/h, head to 125 m, temperature -40°C to +500°C, pressure to 50 bar

  • Features: separate discharge pipe, submerged impeller (no shaft seal), heating jacket for high temperature melting materials

  • API 610 11th Edition compliant.

Xi’an Pump & Valve Plant (RBS Series)

  • RBS series urea melt pump specifically designed for molten urea

  • Standard: API 610, with heating jacket

  • Impeller: double suction closed structure or open type

  • Seal: packing + auxiliary impeller, or bellows mechanical seal

  • Bearing housing with water cooling chamber

  • Materials: TA2, 316L, 316, 304L, 2205

  • Flow: 2.5–1,200 m³/h, head ≤180 m, operating pressure ≤1.6 MPa, temperature -20°C to +180°C.

Beijing Changjia Pump Industry (LY Series)

  • LY series single casing VS4 pump per API 610 11th Edition

  • Single stage, single suction, radial split long shaft liquid submerged pump

  • Flow to 800 m³/h, head to 200 m, operating pressure to 2.5 MPa, temperature -20°C to +420°C

  • Double volute casing for DN≥80 mm balances radial forces

  • Heating jacket option on discharge column, pipe, and casing

  • No shaft seal required (separate discharge column)

  • Shaft depth to 10 m.

Jiangsu Feiyue Pump (VS4 high temperature pump)

  • VS1, VS4, VS4+, VS5 series for high temperature molten materials

  • Patented dynamic pressure liquid film bearing support technology

  • NH-8 high temperature self-lubricating wear-resistant alloy for sliding bearings

  • Flow: 2–3,000 m³/h, head to 500 m, temperature 100–850°C

  • Used in fertilizer plant molten material transfer

Dalian Kehuan Pump

  • API 610 VS4 long shaft submerged centrifugal pump

  • Suction size DN40–DN400

  • Clean or liquid with small solid particles content

  • Chemical, petrochemical, and natural gas industry processes.

Liaoning Demeter Technology (XLY Series)

  • Long shaft submerged pump per API 610 11th Edition VS4

  • Single stage, single suction, suspended installation

  • Single layer volute casing, long shaft drive

  • Double volute casing for sizes ≥DN80 to balance radial forces

  • Multiple support design, shaft depth to 10 m

  • Flow to 400 m³/h, head to 100 m, pressure 1.6 MPa, temperature -20°C to +180°C.

Anhui Sanlian Pump (ASP5540 Series)

  • Long shaft submerged pump (single stage, single suction, volute type) to API 610 VS4 configuration

  • Designed per ISO 2858 performance, meets parts of API 610 10th Edition.

Yantai Sunshine Pump (LG Series)

  • High temperature vertical liquid submerged pump for molten material transfer.

Why Choose a China API 610 VS4 Urea Melt Pump Manufacturer?

As a specialized China API 610 VS4 pump manufacturer with extensive experience in fertilizer plant urea melt transfer, we deliver:

  • Full API 610 11th Edition (ISO 13709) compliance — designed, manufactured, and tested to international standards for process pumps

  • Specifically designed for urea melt — heating jackets (steam or electric), high-temperature bearings, and materials suitable for 150°C urea melt

  • Corrosion-resistant materials — 304SS and 316SS standard; duplex and high alloys available

  • Range of configurations — open or closed impeller, with or without top mechanical seal, multiple shaft lengths

  • Complete heating jacket integration — casing and column pipe jackets with steam connections tested before shipment

  • Competitive capital cost — typically 20–30% lower than major Western brands for equivalent VS4 configurations

  • Shorter lead times — 20–28 weeks for standard stainless steel configurations

  • Factory testing — hydraulic performance testing, mechanical run testing, vibration and bearing temperature monitoring, steam jacket pressure testing

  • Complete documentation — performance curves, sectional drawings, GA drawings, API 610 datasheet, material certifications, installation and maintenance manuals

  • Global shipping — export packaging (wooden crates, VCI, desiccant) and export documentation

  • Spare parts availability — critical spares (impellers, shafts, guide bearings, gaskets) stocked

  • Installation and commissioning support — on-site supervision, training, and after-sales service

Industry Applications

API 610 VS4 urea melt pumps serve critical applications in fertilizer industry:

Urea Prilling Towers:

  • Transfer molten urea from evaporator melt pit to prilling tower top

  • Distribution to spray heads for droplet formation and solidification

Urea Granulation:

  • Feed molten urea to fluid bed or drum granulator

  • Circulation in granulation loop

Urea Storage:

  • Transfer from melt pit to storage tank

  • Re-circulation to maintain temperature in storage

Urea Formulation Plants (UAN, NPK):

  • Feed urea melt to mixing section for UAN production

  • Component feed for blended NPK fertilizers

Other Molten Material Transfer (same pump platform):

  • Molten ammonium nitrate

  • Hot sulphur (with appropriate materials)

  • Hot bitumen and asphalt

  • Paraffin wax

  • High-temperature chemical process liquors

Summary — Urea Melt Pump (API 610 VS4)

ParameterSpecification
Pump TypeAPI 610 Type VS4 — Vertical, single casing, volute, long shaft sump pump
MediumMolten urea (urea melt), 95–99.7% concentration
Operating temperature135–150°C (Design: -20°C to +180°C)
Design pressureUp to 1.6–2.5 MPa
Flow range2–1,200 m³/h (selectable)
Head rangeUp to 200 m
Shaft length3–10 m (standard; longer custom)
CasingSingle stage volute (double volute ≥DN80)
ImpellerOpen type (standard); closed optional
Materials304SS / 316SS for wetted parts; carbon steel for structural
Heating jacketIntegral on casing and column pipe; ≤0.6 MPa steam, ≤170°C
SealNo submerged seal (separate discharge column); optional top seal per API 682
Guide bearingsPTFE-lined bronze or carbon, water-flushed
MountingFlanged mounting on pit cover; motor at grade
CertificationAPI 610 11th Edition (ISO 13709)

For more information or a custom engineering proposal for your urea melt pump (VS4, molten urea transfer) application, please contact us at:

info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit