| Size | Connection | Bevel Diameter ±0.4 | Tube OD +1.6/-0.8 | Tool Joint OD +1.6/-0.8 | Max Elevator Upset D_eu | Center Upset D_cu +1.6/-0.8 | Tube ID D | Tool Joint ID +3.2/0 | Min Drift Diameter |
|---|---|---|---|---|---|---|---|---|---|
| 88.9 | NC38 | 116.3 | 88.9 | 120.6 (123.8/127.0 opt.) | 98.4 | 101.6 | 52.4 | 52.4 | 46.0 |
| 101.6 | NC40 | 127.4 | 101.6 | 133.4 | 106.4 | 114.3 | 63.5 | 63.5 | 57.2 |
| 114.3 | NC46 | 145.3 | 114.3 | 158.8 | 119.1 | 127.0 | 68.2 | 68.2 | 61.9 |
| 127.0 | NC50 | 154.0 | 127.0 | 168.3 | 130.2 | 139.7 | 76.2 | 76.2 | 69.8 |
| 139.7 | 5½FH | 170.7 | 139.7 | 177.8 (184.2/190.5 opt.) | 144.4 | 152.4 | 82.6 | 82.6 | 76.2 |
| 149.2 | 5½FH | 170.7 | 149.2 | 177.8 | 152.4 | 161.9 | 101.6 | 101.6 | 95.3 |
| 168.2 | 6⅝FH | 195.7 | 168.2 | 203.2 (209.6/215.9 opt.) | 176.2 | 181.0 | 101.6 | 101.6 | 95.2 |
Data source: Technical data table.
All dimensions are in millimeters. Optional tool joint ODs are shown in parentheses. Verify clearance and elevator compatibility before ordering. Hardbanding can be applied to the tool joint and center upset areas to extend service life in abrasive formations.
The integral heavy weight drill pipe is formed by hot forging and fully heat-treated. It features a thick wall with an integral tool joint and a center upset. The center upset acts as a wear pad and stabilizer, keeping the pipe off the hole wall and reducing buckling tendency. It provides a smooth transition of stiffness between the drill pipe and drill collars.
Replacing an existing integral HWDP string? Check these points before matching:
For standard (non-heavy) drill pipe transitions, see our Drill Collar range. For magnetic isolation, see the Non-Magnetic HWDP page.
Not sure about the connection or hardbanding specification? Provide your hole size, drill pipe connection, and expected dogleg severity, and our engineers will recommend the best configuration.
Q: What is the difference between integral HWDP and standard drill pipe?
A: Integral HWDP has a thicker wall, integral tool joints, and a center upset, providing higher buckling resistance and weight on bit.
Q: What hardbanding materials are available?
A: Arno 100XT and 300XT hardbanding are available, applied to the tool joint and center upset.
Q: Can the tool joint OD be customized?
A: Yes, optional tool joint ODs are available for certain sizes to match specific hole clearances.
Q: What is the typical lead time?
A: Lead time varies by size, connection, and hardbanding requirements. Contact our team for a precise schedule, especially for urgent downtime needs.
Q: Are material certificates provided?
A: Yes, material test reports (MTR) for AISI 4145H are provided with every shipment.
Please follow standard industrial safety procedures during installation and maintenance.
For integral heavy weight drill pipe selection and spare parts, contact HYRIG: info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.