| Size | Connection | Bevel Diameter ±0.4 | Tube OD +1.6/-0.8 | Tool Joint OD +1.6/-0.8 | Center Upset D_cu +1.6/-0.8 | Tube ID D | Tool Joint ID +3.2/0 | Min Drift Diameter |
|---|---|---|---|---|---|---|---|---|
| 88.9 | NC38 | 116.3 | 88.9 | 120.6 (123.8/127.0 opt.) | 101.6 | 52.4 | 52.4 | 46.0 |
| 101.6 | NC40 | 127.4 | 101.6 | 133.4 | 114.3 | 63.5 | 63.5 | 57.2 |
| 114.3 | NC46 | 145.3 | 114.3 | 158.8 | 127.0 | 68.2 | 68.2 | 61.9 |
| 127.0 | NC50 | 154.0 | 127.0 | 168.3 | 139.7 | 76.2 | 76.2 | 69.8 |
| 139.7 | 5½FH | 170.7 | 139.7 | 177.8 (184.2/190.5 opt.) | 152.4 | 82.6 | 82.6 | 76.2 |
| 149.2 | 5½FH | 170.7 | 149.2 | 177.8 | 161.9 | 101.6 | 101.6 | 95.3 |
| 168.2 | 6⅝FH | 195.7 | 168.2 | 203.2 (209.6/215.9 opt.) | 181.0 | 101.6 | 101.6 | 95.2 |
Data source: Technical data table.
All dimensions are in millimeters. The non-magnetic HWDP uses a thick-wall tubular body with a center upset. When confirming fit, ensure the tool joint OD clears the hole and the tube ID allows passage of MWD/LWD tools.
The non-magnetic HWDP is made from low-carbon stainless steel, which limits magnetic permeability and isolates survey instruments from steel drill string interference. The center upset provides additional stiffness and wear resistance. Threads can be cold rolled for fatigue resistance in directional wells.
Replacing an existing non-magnetic HWDP? Check these points:
For standard transition members without magnetic isolation, see the Integral Heavy Weight Drill Pipe page. For magnetic isolation directly above the bit, see the Non-Magnetic Drill Collar range.
Not sure which OD and ID combination fits your BHA? Send the hole size, MWD/LWD tool OD, and adjacent drill pipe connection, and our engineers will match the tool joint OD and center upset dimensions.
Q: What is the magnetic permeability of this non-magnetic HWDP?
A: μr is ≤1.010, with survey-grade options at ≤1.005 μr available upon request.
Q: What is the difference between non-magnetic HWDP and a standard drill collar?
A: Non-magnetic HWDP uses low-carbon stainless steel for magnetic isolation and a smaller OD for transition; drill collars use AISI 4145H for maximum weight and stiffness.
Q: Can the tool joint OD be customized?
A: Yes. Optional tool joint ODs are available for select sizes; specify the required OD during inquiry.
Q: Are MTR and magnetic certificates included?
A: Yes. Material test reports and magnetic property certificates are provided against the heat number.
Q: What is the typical lead time?
A: Lead time depends on OD, connection, and thread treatment. Confirm with our team for year-end shutdown or urgent downtime planning.
Please follow standard industrial safety procedures during installation and maintenance.
For non-magnetic heavy weight drill pipe selection and spare parts, contact HYRIG: info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.