ISO 15552 Cylinder Cross-Reference | Bore, Stroke, Mounting

2026-11-08 19:24

ISO 15552 Cylinder Cross-Reference | Bore, Stroke, Mounting

This ISO 15552 cross-reference covers the mounting dimensions, port threads, and piston rod threads for bore sizes 32 mm to 320 mm. It explains what the standard defines — and what it does not — so that a Festo DSBC or any other ISO 15552 cylinder can be matched to an existing machine without guessing. The standard covers cylinders with a maximum rated pressure of 10 bar and removable mountings, but it does not standardize cushioning behaviour, seal material, or sensor slot geometry.

What ISO 15552 Standardizes

ISO 15552 defines the basic dimensions, mounting dimensions, and accessory dimensions for pneumatic cylinders with removable mountings, bore sizes 32–320 mm, and a maximum rated pressure of 10 bar. The standard covers:

  • Bore sizes: 32, 40, 50, 63, 80, 100, 125, 160, 200, 250, 320 mm.
  • Mounting interface: the foot, flange, and clevis dimensions are defined so that a cylinder from one manufacturer can be mounted on a bracket designed for another manufacturer of the same bore.
  • Port thread: the port thread for each bore size is defined (e.g., G1/8 for 32 mm, G1/4 for 40 mm, G3/8 for 63 mm, G1/2 for 100/125 mm).
  • Piston rod thread: the piston rod thread for each bore size is defined (e.g., M10×1.25 for 32 mm, M12×1.25 for 40 mm, M16×1.5 for 50/63 mm, M20×1.5 for 80/100 mm, M27×2 for 125 mm).

What ISO 15552 Does Not Standardize

ISO 15552 does not standardize:

  • Cushioning behaviour: adjustable vs self-adjusting, cushioning length, and impact energy rating.
  • Seal material: NBR, TPE-U(PU), FKM, or other elastomers may be used depending on the manufacturer and the temperature range.
  • Temperature range: the permissible ambient and media temperature depends on the seal material and the cylinder construction.
  • Sensor slot geometry: the position and depth of the sensor slot for proximity switches are not defined by the standard.
  • Port orientation: the angular position of the ports relative to the mounting bracket is not standardized.

ISO 15552 Bore and Thread Cross-Reference

BorePort threadPiston rod threadTypical theoretical force at 6 bar, advance
32 mmG1/8M10 × 1.25483 N
40 mmG1/4M12 × 1.25754 N
50 mmG1/4M16 × 1.51178 N
63 mmG3/8M16 × 1.51870 N
80 mmG3/8M20 × 1.53016 N
100 mmG1/2M20 × 1.54712 N
125 mmG1/2M27 × 27363 N
160 mmG3/4M36 × 212064 N
200 mmG3/4M36 × 218850 N
250 mmG1M42 × 229452 N
320 mmG1M42 × 248255 N

Data source: Technical data table.

Using the Cross-Reference for Replacement

When replacing an existing ISO 15552 cylinder, start with the bore and stroke, then confirm the port thread and piston rod thread against the table above. If the existing cylinder uses a non-standard port thread or piston rod thread, an adapter may be required.

After the mechanical interface is confirmed, check the cushioning behaviour and the sensor slot geometry — these are the two areas where two ISO 15552 cylinders of the same bore and stroke can still differ. If the existing machine relies on a specific cushioning setting, confirm whether the replacement cylinder has adjustable or self-adjusting cushioning. If the existing proximity switches are mounted in the sensor slot, confirm the slot depth and position.

Selection Support

Not sure which ISO 15552 bore and stroke match your existing cylinder? Send the existing cylinder model number, the port thread, the piston rod thread, and the mounting bracket part number, and we will confirm the replacement model and any adapters required. Explore the Festo DSBC ISO 15552 cylinder overview for a specific series, or the DNC to DSBC replacement guide for a step-by-step DNC replacement checklist.

Frequently Asked Questions

Q: What bore sizes does ISO 15552 cover?
A: ISO 15552 covers bore sizes from 32 mm to 320 mm, with a maximum rated pressure of 10 bar.

Q: Does ISO 15552 standardize the port thread?
A: Yes. The port thread for each bore size is defined by the standard (e.g., G1/8 for 32 mm, G1/4 for 40 mm, G3/8 for 63 mm).

Q: Does ISO 15552 standardize cushioning?
A: No. Cushioning behaviour (adjustable vs self-adjusting), cushioning length, and impact energy rating are not standardized and can differ between manufacturers.

Q: Can I replace a DNC cylinder with a DSBC cylinder without changing the bracket?
A: Yes, if both follow ISO 15552 and the bore is the same. The mounting dimensions are standardized. However, confirm the port orientation, cushioning behaviour, and sensor slot geometry before treating it as a complete drop-in replacement.

Q: What is the maximum pressure for an ISO 15552 cylinder?
A: The standard defines a maximum rated pressure of 10 bar. Some manufacturers offer cylinders rated to 12 bar, but the ISO 15552 dimensions are defined at the 10 bar rating.

Contact

For ISO 15552 cylinder cross-reference and replacement verification, contact HYRIG: info@hyrig.com.

Related Pages

Name:
Message:
Verification code:
Submit
Comment