Festo DSBC ISO 15552 Cylinders | Complete Bore & Stroke Range

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO DSBC ISO 15552 cylinder range and its variants. The DSBC series is a double-acting profile cylinder to ISO 15552, available in bore sizes from 32 mm to 320 mm, with PPVA adjustable or PPSA self-adjusting pneumatic cushioning. It is the successor to the FESTO DNC and DNCB series, and the ISO 15552 dimensions allow replacement of the preceding series. This overview covers the complete DSBC model range, key specifications, and selection guidance.
Conatct For Details
DetailReview(0)Additional

Festo DSBC ISO 15552 Cylinders | Complete Bore & Stroke Range

HYRIG can supply the FESTO DSBC ISO 15552 cylinder range and its variants. The DSBC series is a double-acting profile cylinder to ISO 15552, available in bore sizes from 32 mm to 320 mm, with PPVA adjustable or PPSA self-adjusting pneumatic cushioning. It is the successor to the FESTO DNC and DNCB series, and the ISO 15552 dimensions allow replacement of the preceding series. This overview covers the complete DSBC model range, key specifications, and selection guidance.

Key Facts



SeriesDSBC, profile cylinder
StandardISO 15552
Bore range32 mm … 320 mm
Stroke range1 mm … 2800 mm
CushioningPPVA adjustable or PPSA self-adjusting
Operating pressure0.6 bar … 12 bar (bore-dependent)
Position sensingFor proximity sensor
PredecessorDNC / DNCB series

DSBC Complete Model Range & Specifications

BorePiston rod threadPortTheoretical force at 6 bar, advanceTypical stroke rangeCushioning options
32 mmM10 × 1.25G1/8483 N25–500 mmPPVA / PPSA
40 mmM12 × 1.25G1/4754 N25–800 mmPPVA / PPSA
50 mmM16 × 1.5G1/41178 N25–1000 mmPPVA / PPSA
63 mmM16 × 1.5G3/81870 N25–1200 mmPPVA / PPSA
80 mmM20 × 1.5G3/83016 N25–1500 mmPPVA / PPSA
100 mmM20 × 1.5G1/24712 N25–2000 mmPPVA / PPSA
125 mmM27 × 2G1/27363 N25–2000 mmPPVA / PPSA
160 mmM36 × 2G3/412064 N25–2500 mmPPVA / PPSA
200 mmM36 × 2G3/418850 N25–2500 mmPPVA / PPSA
250 mmM42 × 2G129452 N25–2800 mmPPVA / PPSA
320 mmM42 × 2G148255 N25–2800 mmPPVA / PPSA

Data source: Technical data table.

Structure / Working Principle

The DSBC series uses a profile barrel with an extruded aluminium tube and PPVA or PPSA pneumatic cushioning. PPVA is adjustable cushioning with a tuning screw accessible from the outside of the end cap. PPSA is self-adjusting cushioning that adapts to the load without a tuning screw — it reduces changeover time when the load or speed changes, but the operator cannot manually set the deceleration profile.

The ISO 15552 standard defines the mounting dimensions, piston rod thread, and port positions for bore sizes 32–320 mm. This means a DSBC cylinder can replace a DNC, DNCB, or any other ISO 15552 cylinder of the same bore and stroke without changing the mounting bracket or the port fittings. However, ISO 15552 does not standardize the cushioning behavior, the seal material, the temperature range, or the sensor slot geometry — those must be confirmed individually.

Cross-Reference & Replacement

Replacing a DNC or DNCB cylinder with a DSBC? FESTO identifies the DSBC series as the successor to the proven DNC and DNCB series, with ISO 15552-compliant dimensions that allow replacement of the preceding series.

Check these five points before ordering:

  1. Bore and stroke: match the existing cylinder.
  2. Port thread: G1/8, G1/4, G3/8, G1/2, G3/4, or G1 — match the existing fitting.
  3. Cushioning: PPV-A (adjustable) on the DNC vs PPVA (adjustable) or PPSA (self-adjusting) on the DSBC. If the existing application relies on a tuned cushioning setting, confirm the deceleration profile.
  4. Mounting interface: ISO 15552 — the bracket and foot pattern should transfer directly, but confirm the accessory part numbers.
  5. Position sensing: confirm the sensor slot geometry and the proximity switch model.

For a detailed step-by-step checklist, see the FESTO DNC to DSBC replacement guide.

Selection Support

Not sure which DSBC bore and stroke match your existing DNC cylinder? Send the complete DNC part number, the required force, the available space, and the mounting bracket part number, and we will confirm the DSBC model code and cushioning variant. Explore specific DSBC models in the DSBC-40-80-PPVA-N3 cylinder page and the DSBC-63-175-PPVA-N3 cylinder page.

Frequently Asked Questions

Q: What bore sizes are available in the Festo DSBC series?
A: The DSBC series covers bore sizes from 32 mm to 320 mm, with strokes up to 2800 mm depending on the bore.

Q: Is DSBC a direct replacement for DNC?
A: Mechanically yes on the ISO 15552 interface, but verify port thread, stroke, cushioning behavior, and mounting accessory before ordering. DSBC is the successor series, but “drop-in” requires confirming the complete configured interface.

Q: What is the difference between PPVA and PPSA cushioning?
A: PPVA is adjustable pneumatic cushioning with a tuning screw. PPSA is self-adjusting pneumatic cushioning without a tuning screw — it adapts to the load automatically, reducing changeover time.

Q: What is the operating pressure range of the DSBC series?
A: 0.6 bar to 12 bar for most bore sizes, with some larger bores rated from 0.4 bar or 0.2 bar. Confirm the specific bore datasheet before ordering.

Q: Can I get seal kits for DSBC cylinders?
A: Yes, on request. Provide the cylinder model and quantity, and we will confirm the matching seal kit.

Contact

For FESTO DSBC ISO 15552 cylinder selection and DNC replacement verification, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit