HYRIG can supply the FESTO DFM-25-100-B-PPV-A-GF guided cylinder. The FESTO DFM-25-100-B-PPV-A-GF is a double-acting guided drive with a 25 mm piston diameter, 100 mm stroke, a plain-bearing guide, and PPV adjustable pneumatic cushioning at both ends. It delivers 295 N theoretical advance force at 6 bar and weighs 2225 g. The guided output prevents the load from rotating and absorbs lateral forces that would bend a standard piston rod — used in press-fit, lift, and transfer applications where the load must follow a precise linear path.
| Drive type | Guided drive, DFM series |
| Piston diameter | 25 mm |
| Stroke | 100 mm |
| Guide type | Plain-bearing guide (GF) |
| Theoretical force at 6 bar | 295 N advance / 247 N return |
| Cushioning | PPV adjustable pneumatic, both ends |
| Max. force Fz | 810.7 N |
| Product weight | 2225 g |
| Order code | 578876 |
| Model | Guide type | Stroke | Force at 6 bar | Max. force Fz | Weight | Order code |
|---|---|---|---|---|---|---|
| DFM-25-100-B-PPV-A-GF | Plain-bearing | 100 mm | 295 N | 810.7 N | 2225 g | 578876 |
| DFM-25-100-P-A-KF | Recirculating ball bearing | 100 mm | 295 N | 810.7 N | — | 170928 |
| DFM-25-80-P-A-GF | Plain-bearing | 80 mm | 295 N | 810.7 N | — | 170927 |
Explore the full range in the FESTO DFM guided cylinder overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Piston diameter | 25 mm |
| Stroke | 100 mm |
| Guide type | Plain-bearing guide (GF) |
| Operating pressure | 0.15 MPa … 1 MPa (1.5 bar … 10 bar) |
| Max. force Fz | 810.7 N |
| Max. moment Mx | 3.64 Nm |
| Max. moment My | 19.46 Nm |
| Max. moment Mz | 19.46 Nm |
| Product weight | 2225 g |
| Pneumatic connection | G1/8 |
| Operating temperature | -20 °C … +80 °C |
The DFM series is a guided drive that combines a pneumatic cylinder with a guide rod and a yoke plate. The piston rod drives a yoke that slides on one or two guide rods supported by plain bearings. The guide rods absorb lateral forces and moments, so the output yoke plate moves without rotation and without loading the piston rod in bending.
The plain-bearing guide (suffix GF) uses maintenance-free sliding bearings, suitable for moderate side loads and applications where smooth, low-noise motion is more important than the highest possible load capacity. The recirculating ball bearing guide (suffix KF) uses rolling elements for higher load capacity and stiffness, but at higher cost and with more sensitivity to contamination. The PPV adjustable pneumatic cushioning at both ends lets you tune the exhaust air near end position, so the guided load decelerates without hard impact — important when the yoke plate carries a tool or fixture that must not experience shock.
Replacing a discontinued guided cylinder or a competitor guide unit with the DFM-25-100-B-PPV-A-GF? Check these four points before ordering:
For a broader replacement checklist, see the FESTO guided cylinder replacement guide.
Not sure whether the plain-bearing guide (GF) or the recirculating ball bearing guide (KF) is the correct choice for your side load, or need the matching yoke plate accessory? Send your load, side-load direction, required stiffness, moment arm, and mounting interface, and we will confirm the guide type and accessory combination.
Q: What is the theoretical force of the Festo DFM-25-100-B-PPV-A-GF at 6 bar?
A: 295 N advance and 247 N return, based on the 25 mm piston area.
Q: What is the difference between GF and KF guides on the DFM series?
A: GF is a plain-bearing guide, suitable for moderate side loads and smooth motion. KF is a recirculating ball bearing guide, with higher load capacity and stiffness but higher cost and more sensitivity to contamination.
Q: Does the DFM-25-100-B-PPV-A-GF have adjustable cushioning?
A: Yes. The PPV-A suffix indicates adjustable pneumatic cushioning at both ends. The cushioning screws remain accessible after mounting.
Q: What is the maximum side force Fz?
A: 810.7 N, based on the guide rod and bearing capacity. This is the maximum force perpendicular to the direction of motion; the actual permissible load depends on the stroke and the distance from the guide.
Q: What is the lead time for Festo DFM-25-100-B-PPV-A-GF?
A: Standard lead time is 7–17 days from order confirmation, based on the quoted supply status.
For FESTO DFM-25-100-B-PPV-A-GF selection and yoke plate accessories, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.