Festo DSBC-40-80-PPVA-N3 Cylinder | 40 mm Bore 80 mm

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO DSBC-40-80-PPVA-N3 cylinder. The FESTO DSBC-40-80-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 80 mm stroke, G 1/4 ports, and adjustable pneumatic cushioning at both ends. It is used for controlled linear motion where end-of-stroke impact needs to be tuned to the load — machine tool heads, conveyor stops, robotic end-effectors, and material handling pushers.
Conatct For Details
DetailReview(0)Additional

Festo DSBC-40-80-PPVA-N3 Cylinder | 40 mm Bore 80 mm

HYRIG can supply the FESTO DSBC-40-80-PPVA-N3 cylinder. The FESTO DSBC-40-80-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 80 mm stroke, G 1/4 ports, and adjustable pneumatic cushioning at both ends. It is used for controlled linear motion where end-of-stroke impact needs to be tuned to the load — machine tool heads, conveyor stops, robotic end-effectors, and material handling pushers.

Key Facts



Piston diameter40 mm
Stroke80 mm
Mode of operationDouble-acting
CushioningPneumatic, adjustable at both ends (PPV)
Operating pressure0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4]
Ambient temperature-20 °C … +80 °C
Port threadG 1/4
Piston rod threadM12 × 1.25
StandardISO 15552

Legacy reference: DNC-40-80-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series, while cushioning, sensing, ports, rod, and mounting options still require confirmation.

Festo DSBC-40 Model Specifications & Stroke Variants

ModelBoreStrokePortCushioning
DSBC-40-80-PPVA-N340 mm80 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-100-PPVA-N340 mm100 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-125-PPVA-N340 mm125 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-250-PPVA-N340 mm250 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-400-PPVA-N340 mm400 mmG 1/4Adjustable pneumatic, both ends

Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.

Data source: Technical data table.

Dimensions

ItemValue
Mounting standardISO 15552
Mounting typeVia female thread or with accessories
Length at 80 mm strokeConfirm against the FESTO datasheet
Width × height54 mm × 54 mm
Basic weight at 0 mm strokeAvailable on request
Additional weight per 10 mm strokeAvailable on request
Pneumatic connectionG 1/4
Piston rod threadM12 × 1.25

Structure / Working Principle

Compressed air enters one of the two G 1/4 ports and drives the piston in a linear stroke. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position, so the load decelerates without hard impact. The cushioning screws remain accessible after mounting, which means you can re-tune deceleration when load or speed changes — without removing the cylinder from the machine.

The piston rod is male-threaded M12 × 1.25, allowing eye, clevis, or coupler attachments. The profile barrel carries a magnetic piston and sensor slots, so rod position can be detected with proximity switches mounted directly in the slot — no external brackets.

Cross-Reference & Replacement

Replacing a FESTO DNC-40-80-PPV-A? Check these five points before ordering the FESTO DSBC-40-80-PPVA-N3.

  1. Bore and stroke: 40 mm / 80 mm — match.
  2. Port thread: G 1/4 on both DNC and DSBC — match.
  3. Cushioning: DNC PPV-A and DSBC PPVA-N3 are both adjustable pneumatic cushioning at both ends. The adjustment method may differ, so confirm the cushioning screw position on the existing installation.
  4. Mounting interface: both follow ISO 15552. Reuse the existing female-thread mounting, or transfer the foot/flange accessory after confirming the accessory part number.
  5. Force and duty: confirm that the theoretical advance force matches the existing load and cycle rate. DSBC uses a 3K piston rated for higher cushioning energy than DNC, which is a performance upgrade — but it does not remove the need to verify the force margin.

FESTO identifies DSBC as the successor to DNC and DNCB, and ISO 15552-compliant dimensions support replacement of the preceding series. However, ISO 15552 standardizes dimensions within its scope, not every configured option — port orientation, seal material, temperature range, cushion behavior, and switch type still need to be verified individually.

For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.

Applications

  • Machine tool heads: clamping and positioning where adjustable cushioning absorbs end-of-stroke shock during high-cycle operation.
  • Conveyor stops and diverter gates: where the ISO 15552 interface already exists in the conveyor frame, and cushioning needs to be re-tuned when carton weight changes.
  • Robotic end-effectors: actuation or counterbalance where the magnetic piston allows proximity sensor feedback without external brackets.
  • Material handling pushers and lifts: where the 40 mm bore and G 1/4 port match the existing airline, and adjustable cushioning keeps noise low at end of stroke.

Selection Support

Not sure whether the adjustable PPVA cushioning matches your cycle rate, or need the correct ISO 15552 mounting accessory? Send your bore, stroke, load, cycle rate, and existing mounting accessory part number, and we will confirm the model code and accessory combination.

Frequently Asked Questions

Q: What is the operating pressure range of the Festo DSBC-40-80-PPVA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].

Q: Is Festo DSBC-40-80-PPVA-N3 a direct replacement for DNC-40-80-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread, stroke, cushioning adjustment, mounting accessory, and force margin before release. DSBC is the successor series, but “drop-in” requires confirming the complete configured interface, not just bore and stroke.

Q: Does this Festo cylinder have a magnetic piston for position sensing?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches. No external bracket is needed for standard sensor mounting.

Q: Can the cushioning be adjusted after installation?
A: Yes. The PPV variant has adjustable pneumatic cushioning at both ends, and the cushioning screws remain accessible after mounting.

Q: What is the lead time for Festo DSBC-40-80-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status. For urgent maintenance downtime, ask about stock or the nearest functionally equivalent stroke variant.

Q: Can I get seal kits for the Festo DSBC-40-80-PPVA-N3?
A: Yes, on request. Provide the cylinder model and quantity, and we will confirm the matching seal kit. No part number is published on this page to avoid mismatched kits.

Q: Does the DSBC-40-80-PPVA-N3 work with lubricated air?
A: Yes, but once lubricated air is used, the system must continue with lubricated air. The base operating medium specification is compressed air to ISO 8573-1:2010 [7:4:4].

Contact

For FESTO DSBC-40-80-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit