HYRIG can supply the FESTO DSBC-50-25-PPVA-N3 cylinder. The FESTO DSBC-50-25-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 50 mm piston diameter, 25 mm stroke, G 1/4 ports, and adjustable pneumatic cushioning at both ends. It is a short-stroke, high-force cylinder used for clamping, pressing, and compact transfer motions where 1178 N at 6 bar is needed in a 25 mm travel.
| Piston diameter | 50 mm |
| Stroke | 25 mm |
| Mode of operation | Double-acting |
| Cushioning | Pneumatic, adjustable at both ends (PPV) |
| Operating pressure | 0.4 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4] |
| Ambient temperature | -20 °C … +80 °C |
| Theoretical force at 6 bar | 1178 N advance / 990 N return |
| Port thread | G 1/4 |
| Piston rod thread | M16 × 1.5 |
| Standard | ISO 15552 |
Legacy reference: DNC-50-25-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series.
| Model | Bore | Stroke | Port | Cushioning | Theoretical force at 6 bar, advance |
|---|---|---|---|---|---|
| DSBC-50-25-PPVA-N3 | 50 mm | 25 mm | G 1/4 | Adjustable pneumatic, both ends | 1178 N |
| DSBC-50-50-PPVA-N3 | 50 mm | 50 mm | G 1/4 | Adjustable pneumatic, both ends | 1178 N |
| DSBC-50-80-PPVA-N3 | 50 mm | 80 mm | G 1/4 | Adjustable pneumatic, both ends | 1178 N |
| DSBC-50-100-PPVA-N3 | 50 mm | 100 mm | G 1/4 | Adjustable pneumatic, both ends | 1178 N |
| DSBC-50-160-PPVA-N3 | 50 mm | 160 mm | G 1/4 | Adjustable pneumatic, both ends | 1178 N |
Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Mounting standard | ISO 15552 |
| Length at 25 mm stroke | 186.9 mm |
| Width × height | 62 mm × 62 mm |
| Basic weight at 0 mm stroke | 1190 g |
| Additional weight per 10 mm stroke | 56 g |
| Net weight at 25 mm stroke | 1.33 kg |
| Cushioning length | 22 mm |
| Impact energy in end positions | 1 J |
| Pneumatic connection | G 1/4 |
| Piston rod thread | M16 × 1.5 |
Compressed air enters one of the two G 1/4 ports and drives the piston in a linear stroke. With a 50 mm bore, the theoretical advance force at 6 bar is 1178 N, and the return force is 990 N. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position — important on a short 25 mm stroke where the cushioning travel is limited and hard impact is more likely.
The piston rod is male-threaded M16 × 1.5. The profile barrel carries a magnetic piston and sensor slots for proximity switches.
Replacing a FESTO DNC-50-25-PPV-A? Check these five points before ordering the FESTO DSBC-50-25-PPVA-N3.
For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.
Not sure whether 1178 N at 6 bar is sufficient for your press-fit or clamping load, or need the matching ISO 15552 mounting accessory? Send your load, required force, cycle rate, and existing mounting accessory part number, and we will confirm the model code and accessory combination.
Q: What is the operating pressure range of the Festo DSBC-50-25-PPVA-N3?
A: 0.4 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].
Q: What is the theoretical force at 6 bar?
A: 1178 N advance and 990 N return, based on the 50 mm piston area.
Q: Is Festo DSBC-50-25-PPVA-N3 a direct replacement for DNC-50-25-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread G 1/4, stroke 25 mm, cushioning adjustment, mounting accessory, and force margin before release.
Q: Does a 25 mm stroke need special cushioning attention?
A: Yes. On a short stroke, the cushioning travel is limited, so the adjustable PPV cushioning should be tuned carefully to avoid hard impact. The cushioning length is 22 mm, and the impact energy rating is 1 J per end position.
Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.
Q: What is the lead time for Festo DSBC-50-25-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.
For FESTO DSBC-50-25-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.