HYRIG can supply the FESTO DSBC-40-1040-PPVA-N3 cylinder. The FESTO DSBC-40-1040-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 1040 mm stroke, G 1/4 ports, and adjustable pneumatic cushioning at both ends. It is an extra-long-stroke cylinder used where a 40 mm bore is sufficient for the load but the travel exceeds 1 metre — long-travel gates, wide-format conveyor diverters, and large-format material handling.
| Piston diameter | 40 mm |
| Stroke | 1040 mm |
| Mode of operation | Double-acting |
| Cushioning | Pneumatic, adjustable at both ends (PPV) |
| Operating pressure | 0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4] |
| Ambient temperature | -20 °C … +80 °C |
| Port thread | G 1/4 |
| Piston rod thread | M12 × 1.25 |
| Standard | ISO 15552 |
Legacy reference: DNC-40-1040-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series.
| Model | Bore | Stroke | Port | Cushioning |
|---|---|---|---|---|
| DSBC-40-400-PPVA-N3 | 40 mm | 400 mm | G 1/4 | Adjustable pneumatic, both ends |
| DSBC-40-500-PPVA-N3 | 40 mm | 500 mm | G 1/4 | Adjustable pneumatic, both ends |
| DSBC-40-700-PPVA-N3 | 40 mm | 700 mm | G 1/4 | Adjustable pneumatic, both ends |
| DSBC-40-800-PPVA-N3 | 40 mm | 800 mm | G 1/4 | Adjustable pneumatic, both ends |
| DSBC-40-1040-PPVA-N3 | 40 mm | 1040 mm | G 1/4 | Adjustable pneumatic, both ends |
Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Mounting standard | ISO 15552 |
| Length at 1040 mm stroke | Confirm against the FESTO datasheet |
| Width × height | 54 mm × 54 mm |
| Basic weight at 0 mm stroke | Available on request |
| Additional weight per 10 mm stroke | Available on request |
| Pneumatic connection | G 1/4 |
| Piston rod thread | M12 × 1.25 |
Compressed air enters one of the two G 1/4 ports and drives the piston in a linear stroke. On a 1040 mm stroke, the moving mass and rod length are substantially higher than on standard strokes. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position, but rod support or an external guide is strongly recommended to prevent rod bending and vibration over the 1-metre travel.
The piston rod is male-threaded M12 × 1.25. The profile barrel carries a magnetic piston and sensor slots for proximity switches. For strokes above 1000 mm, confirm the mounting support spacing and alignment with the machine frame before installation.
Replacing a FESTO DNC-40-1040-PPV-A? Check these five points before ordering the FESTO DSBC-40-1040-PPVA-N3.
For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.
Not sure whether a 40 mm bore is sufficient over a 1040 mm stroke, or need the correct ISO 15552 mounting accessory and rod support arrangement? Send your load, side-load conditions, mounting spacing, cycle rate, and existing mounting accessory part number, and we will confirm the model code and support requirements.
Q: What is the operating pressure range of the Festo DSBC-40-1040-PPVA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].
Q: Is Festo DSBC-40-1040-PPVA-N3 a direct replacement for DNC-40-1040-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread G 1/4, stroke 1040 mm, cushioning adjustment, mounting accessory, force margin, and rod support before release.
Q: Does a 1040 mm stroke need rod support?
A: Strongly recommended. At 1040 mm stroke, the rod is exposed to buckling, vibration, and misalignment risk. An external guide or rod support is recommended for most applications — send the load and mounting details and we will confirm.
Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.
Q: What is the lead time for Festo DSBC-40-1040-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status. Extra-long strokes may require additional confirmation.
For FESTO DSBC-40-1040-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.