Festo DSBC-40-400-PPVA-N3 Cylinder | 40 mm Bore 400 mm

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO DSBC-40-400-PPVA-N3 cylinder. The FESTO DSBC-40-400-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 400 mm stroke, G 1/4 ports, and adjustable pneumatic cushioning at both ends. It is used where a mid-size bore and a long stroke are both required — long-throw conveyor diverters, large gate actuators, and heavy-load transfer slides.
Conatct For Details
DetailReview(0)Additional

Festo DSBC-40-400-PPVA-N3 Cylinder | 40 mm Bore 400 mm

HYRIG can supply the FESTO DSBC-40-400-PPVA-N3 cylinder. The FESTO DSBC-40-400-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 400 mm stroke, G 1/4 ports, and adjustable pneumatic cushioning at both ends. It is used where a mid-size bore and a long stroke are both required — long-throw conveyor diverters, large gate actuators, and heavy-load transfer slides.

Key Facts



Piston diameter40 mm
Stroke400 mm
Mode of operationDouble-acting
CushioningPneumatic, adjustable at both ends (PPV)
Operating pressure0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4]
Ambient temperature-20 °C … +80 °C
Port threadG 1/4
Piston rod threadM12 × 1.25
StandardISO 15552

Legacy reference: DNC-40-400-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series, while cushioning, sensing, ports, rod, and mounting options still require confirmation.

Festo DSBC-40 Model Specifications & Stroke Variants

ModelBoreStrokePortCushioning
DSBC-40-80-PPVA-N340 mm80 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-100-PPVA-N340 mm100 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-140-PPVA-N340 mm140 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-250-PPVA-N340 mm250 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-400-PPVA-N340 mm400 mmG 1/4Adjustable pneumatic, both ends

Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.

Data source: Technical data table.

Dimensions

ItemValue
Mounting standardISO 15552
Mounting typeVia female thread or with accessories
Length at 400 mm strokeConfirm against the FESTO datasheet
Width × height54 mm × 54 mm
Basic weight at 0 mm strokeAvailable on request
Additional weight per 10 mm strokeAvailable on request
Pneumatic connectionG 1/4
Piston rod threadM12 × 1.25

Structure / Working Principle

Compressed air enters one of the two G 1/4 ports and drives the piston in a linear stroke. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position, so the load decelerates without hard impact — especially important on a 400 mm stroke where the moving mass is higher. The cushioning screws remain accessible after mounting.

The piston rod is male-threaded M12 × 1.25. The profile barrel carries a magnetic piston and sensor slots for proximity switches. On long strokes, rod support or an external guide may be required to prevent rod bending; confirm with the application load and side-load conditions.

Cross-Reference & Replacement

Replacing a FESTO DNC-40-400-PPV-A? Check these five points before ordering the FESTO DSBC-40-400-PPVA-N3.

  1. Bore and stroke: 40 mm / 400 mm — match.
  2. Port thread: G 1/4 on both DNC and DSBC — match.
  3. Cushioning: DNC PPV-A and DSBC PPVA-N3 are both adjustable pneumatic cushioning at both ends. Confirm the cushioning screw position on the existing installation.
  4. Mounting interface: both follow ISO 15552. Reuse the existing female-thread mounting, or transfer the foot/flange accessory after confirming the accessory part number.
  5. Force and duty: at 40 mm bore, the theoretical advance force at 6 bar is approximately 754 N. Confirm this matches the existing load and cycle rate, and check whether the long stroke introduces rod bending risk.

For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.

Applications

  • Long-throw conveyor diverters: where the 400 mm stroke covers the full diverter travel and 40 mm bore provides sufficient force for the load.
  • Large gate actuators: where the gate travel exceeds 300 mm and adjustable cushioning prevents impact noise at end of stroke.
  • Heavy-load transfer slides: where the ISO 15552 interface is already present and the load requires more than 600 N thrust.
  • Replacement of DNC-40-400-PPV-A units: in existing European-built machinery with ISO 15552 mounting.

Selection Support

Not sure whether the 40 mm bore provides enough force over a 400 mm stroke, or need the correct ISO 15552 mounting accessory and rod support? Send your load, side-load conditions, cycle rate, supply pressure, and existing mounting accessory part number, and we will confirm the model code and accessory combination.

Frequently Asked Questions

Q: What is the operating pressure range of the Festo DSBC-40-400-PPVA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].

Q: Is Festo DSBC-40-400-PPVA-N3 a direct replacement for DNC-40-400-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread G 1/4, stroke 400 mm, cushioning adjustment, mounting accessory, force margin, and rod bending risk before release.

Q: What is the theoretical advance force at 6 bar?
A: Approximately 754 N at 6 bar, based on the 40 mm piston area. Confirm the actual load and side-load conditions before sizing.

Q: Does a 400 mm stroke need rod support?
A: It depends on the side load and the load attachment. For pure axial loads within the cylinder's rated buckling limit, no external support is needed. For side loads or long rod extensions, an external guide or rod support is recommended — send the load details and we will confirm.

Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.

Q: What is the lead time for Festo DSBC-40-400-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.

Contact

For FESTO DSBC-40-400-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit