Festo DSBC-40-100-PPSA-N3 Cylinder | 40 mm Bore 100 mm

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO DSBC-40-100-PPSA-N3 cylinder. The FESTO DSBC-40-100-PPSA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 100 mm stroke, G 1/4 ports, and self-adjusting pneumatic cushioning at both ends. It is used where changeover time matters — packaging lines with frequent format changes, quick-change fixtures, and applications where operators should not need to tune cushioning screws.
Conatct For Details
DetailReview(0)Additional

Festo DSBC-40-100-PPSA-N3 Cylinder | 40 mm Bore 100 mm

HYRIG can supply the FESTO DSBC-40-100-PPSA-N3 cylinder. The FESTO DSBC-40-100-PPSA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 100 mm stroke, G 1/4 ports, and self-adjusting pneumatic cushioning at both ends. It is used where changeover time matters — packaging lines with frequent format changes, quick-change fixtures, and applications where operators should not need to tune cushioning screws.

Key Facts



Piston diameter40 mm
Stroke100 mm
Mode of operationDouble-acting
CushioningPneumatic, self-adjusting at both ends (PPSA)
Operating pressure0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4]
Ambient temperature-20 °C … +80 °C
Port threadG 1/4
Piston rod threadM12 × 1.25
StandardISO 15552

Legacy reference: DNC-40-100-PPV-A (discontinued, replaced by this model). Note: DNC PPV-A uses manually adjustable cushioning; DSBC PPSA-N3 uses self-adjusting cushioning. Both are pneumatic, but the adjustment method differs — this is a functional upgrade, not a direct tuning match.

Festo DSBC-40 Model Specifications & Stroke Variants

ModelBoreStrokePortCushioning
DSBC-40-80-PPVA-N340 mm80 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-80-PPSA-N340 mm80 mmG 1/4Self-adjusting pneumatic, both ends
DSBC-40-100-PPVA-N340 mm100 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-100-PPSA-N340 mm100 mmG 1/4Self-adjusting pneumatic, both ends
DSBC-40-125-PPVA-N340 mm125 mmG 1/4Adjustable pneumatic, both ends

Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.

Data source: Technical data table.

Dimensions

ItemValue
Mounting standardISO 15552
Mounting typeVia female thread or with accessories
Length at 100 mm strokeConfirm against the FESTO datasheet
Width × height54 mm × 54 mm
Basic weight at 0 mm strokeAvailable on request
Additional weight per 10 mm strokeAvailable on request
Pneumatic connectionG 1/4
Piston rod threadM12 × 1.25

Structure / Working Principle

Compressed air enters one of the two G 1/4 ports and drives the piston in a linear stroke. The self-adjusting pneumatic cushioning at both ends automatically adapts to the load, so there is no cushioning screw to tune. This is the key difference from the PPVA variant: PPVA requires manual adjustment at commissioning and whenever the load changes; PPSA adjusts itself, which reduces changeover time and prevents mis-adjustment by operators.

The piston rod is male-threaded M12 × 1.25. The profile barrel carries a magnetic piston and sensor slots for proximity switches.

Cross-Reference & Replacement

Replacing a FESTO DNC-40-100-PPV-A? Check these five points before ordering the FESTO DSBC-40-100-PPSA-N3.

  1. Bore and stroke: 40 mm / 100 mm — match.
  2. Port thread: G 1/4 on both DNC and DSBC — match.
  3. Cushioning: DNC PPV-A uses manually adjustable cushioning; DSBC PPSA-N3 uses self-adjusting cushioning. Both are pneumatic, but the adjustment method differs. If your process relies on a specific cushioning setting, the PPSA will self-adjust and may change the deceleration profile. If you need to preserve the manual adjustment, choose the PPVA variant instead.
  4. Mounting interface: both follow ISO 15552. Reuse the existing female-thread mounting, or transfer the foot/flange accessory after confirming the accessory part number.
  5. Force and duty: at 40 mm bore, the theoretical advance force at 6 bar is approximately 754 N. Confirm this matches the existing load and cycle rate.

For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.

Applications

  • Packaging lines with frequent format changes: where self-adjusting cushioning removes the need to re-tune after each changeover.
  • Quick-change fixtures: where operators should not need to adjust cushioning screws between product variants.
  • High-cycle pick-and-place: where consistent deceleration without manual tuning reduces setup time.
  • Replacement of DNC-40-100-PPV-A units where manual tuning is a bottleneck: the PPSA variant removes the tuning step, but confirm the deceleration profile is acceptable for the load.

Selection Support

Not sure whether PPSA self-adjusting cushioning suits your load profile, or need the PPVA variant to preserve manual tuning? Send your load, cycle rate, supply pressure, changeover frequency, and existing mounting accessory part number, and we will confirm the model code and cushioning variant.

Frequently Asked Questions

Q: What is the operating pressure range of the Festo DSBC-40-100-PPSA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].

Q: What is the difference between PPSA and PPVA cushioning?
A: PPSA is self-adjusting pneumatic cushioning — no manual tuning. PPVA is adjustable pneumatic cushioning — the cushioning screw must be tuned at commissioning and when the load changes. PPSA reduces changeover time; PPVA gives the operator direct control over deceleration.

Q: Is Festo DSBC-40-100-PPSA-N3 a direct replacement for DNC-40-100-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but the cushioning changes from manual (PPV-A) to self-adjusting (PPSA). Verify port thread G 1/4, stroke 100 mm, mounting accessory, and whether the self-adjusting deceleration profile is acceptable for your load.

Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.

Q: What is the lead time for Festo DSBC-40-100-PPSA-N3?
A: Standard lead time is 3–4 weeks from order confirmation, based on the quoted supply status.

Q: Can I get seal kits for the Festo DSBC-40-100-PPSA-N3?
A: Yes, on request. Provide the cylinder model and quantity, and we will confirm the matching seal kit.

Contact

For FESTO DSBC-40-100-PPSA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit