Festo DSBC-40-140-PPVA-N3 Cylinder | 40 mm Bore 140 mm

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO DSBC-40-140-PPVA-N3 cylinder. The FESTO DSBC-40-140-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 140 mm stroke, G 1/4 ports, and adjustable pneumatic cushioning at both ends. It sits between the 125 mm and 160 mm standard strokes, used where the machine envelope requires a mid-length stroke without going to a longer barrel.
Conatct For Details
DetailReview(0)Additional

Festo DSBC-40-140-PPVA-N3 Cylinder | 40 mm Bore 140 mm

HYRIG can supply the FESTO DSBC-40-140-PPVA-N3 cylinder. The FESTO DSBC-40-140-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 40 mm piston diameter, 140 mm stroke, G 1/4 ports, and adjustable pneumatic cushioning at both ends. It sits between the 125 mm and 160 mm standard strokes, used where the machine envelope requires a mid-length stroke without going to a longer barrel.

Key Facts



Piston diameter40 mm
Stroke140 mm
Mode of operationDouble-acting
CushioningPneumatic, adjustable at both ends (PPV)
Operating pressure0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4]
Ambient temperature-20 °C … +80 °C
Port threadG 1/4
Piston rod threadM12 × 1.25
StandardISO 15552

Legacy reference: DNC-40-140-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series.

Festo DSBC-40 Model Specifications & Stroke Variants

ModelBoreStrokePortCushioning
DSBC-40-80-PPVA-N340 mm80 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-100-PPVA-N340 mm100 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-125-PPVA-N340 mm125 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-140-PPVA-N340 mm140 mmG 1/4Adjustable pneumatic, both ends
DSBC-40-250-PPVA-N340 mm250 mmG 1/4Adjustable pneumatic, both ends

Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.

Data source: Technical data table.

Dimensions

ItemValue
Mounting standardISO 15552
Length at 140 mm stroke301.9 mm
Width × height54 mm × 54 mm
Net weight at 140 mm stroke1.24 kg
Pneumatic connectionG 1/4
Piston rod threadM12 × 1.25

Structure / Working Principle

Compressed air enters one of the two G 1/4 ports and drives the piston in a linear stroke. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position, so the load decelerates without hard impact. The cushioning screws remain accessible after mounting.

The piston rod is male-threaded M12 × 1.25. The profile barrel carries a magnetic piston and sensor slots for proximity switches. On a 140 mm stroke, side-load risk is moderate; an external guide is recommended only if the load attachment introduces lateral force.

Cross-Reference & Replacement

Replacing a FESTO DNC-40-140-PPV-A? Check these five points before ordering the FESTO DSBC-40-140-PPVA-N3.

  1. Bore and stroke: 40 mm / 140 mm — match.
  2. Port thread: G 1/4 on both DNC and DSBC — match.
  3. Cushioning: DNC PPV-A and DSBC PPVA-N3 are both adjustable pneumatic cushioning at both ends. Confirm the cushioning screw position on the existing installation.
  4. Mounting interface: both follow ISO 15552. Reuse the existing female-thread mounting, or transfer the foot/flange accessory after confirming the accessory part number.
  5. Force and duty: confirm that the theoretical advance force at 6 bar matches the existing load and cycle rate.

For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.

Applications

  • Mid-length conveyor stops: where 140 mm stroke covers the gap between standard 125 mm and 160 mm positions, and the machine frame cannot accommodate a longer barrel.
  • Packaging flap actuators: where a 140 mm stroke matches the flap travel and adjustable cushioning reduces end-of-stroke noise.
  • Light-load transfer slides: where the ISO 15552 interface is already present and 40 mm bore provides sufficient thrust.
  • Replacement of DNC-40-140-PPV-A units: in existing machinery with ISO 15552 mounting.

Selection Support

Not sure whether 140 mm is the correct stroke for your machine envelope, or need the matching ISO 15552 mounting accessory? Send your required travel, load, cycle rate, and existing mounting accessory part number, and we will confirm the model code and accessory combination.

Frequently Asked Questions

Q: What is the operating pressure range of the Festo DSBC-40-140-PPVA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].

Q: Is Festo DSBC-40-140-PPVA-N3 a direct replacement for DNC-40-140-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread G 1/4, stroke 140 mm, cushioning adjustment, and mounting accessory before release.

Q: What is the net weight at 140 mm stroke?
A: 1.24 kg, based on the configured cylinder. Basic weight at 0 mm stroke and additional weight per 10 mm stroke are available on request.

Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.

Q: What is the lead time for Festo DSBC-40-140-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.

Contact

For FESTO DSBC-40-140-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit