HYRIG can supply the FESTO DSBC-32-250-PPVA-N3 cylinder. The FESTO DSBC-32-250-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 32 mm piston diameter, 250 mm stroke, G 1/8 ports, and adjustable pneumatic cushioning at both ends. It is used where a compact bore and long stroke are both required — packaging pushers, long-throw gates, and light-load transfer stations.
| Piston diameter | 32 mm |
| Stroke | 250 mm |
| Mode of operation | Double-acting |
| Cushioning | Pneumatic, adjustable at both ends (PPV) |
| Operating pressure | 0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4] |
| Ambient temperature | -20 °C … +80 °C |
| Port thread | G 1/8 |
| Piston rod thread | M10 × 1.25 |
| Standard | ISO 15552 |
Legacy reference: DNC-32-250-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series, while cushioning, sensing, ports, rod, and mounting options still require confirmation.
| Model | Bore | Stroke | Port | Cushioning |
|---|---|---|---|---|
| DSBC-32-50-PPVA-N3 | 32 mm | 50 mm | G 1/8 | Adjustable pneumatic, both ends |
| DSBC-32-80-PPVA-N3 | 32 mm | 80 mm | G 1/8 | Adjustable pneumatic, both ends |
| DSBC-32-100-PPVA-N3 | 32 mm | 100 mm | G 1/8 | Adjustable pneumatic, both ends |
| DSBC-32-160-PPVA-N3 | 32 mm | 160 mm | G 1/8 | Adjustable pneumatic, both ends |
| DSBC-32-250-PPVA-N3 | 32 mm | 250 mm | G 1/8 | Adjustable pneumatic, both ends |
Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Mounting standard | ISO 15552 |
| Mounting type | Via female thread or with accessories |
| Length at 250 mm stroke | Confirm against the FESTO datasheet |
| Width × height | 45 mm × 45 mm |
| Basic weight at 0 mm stroke | Available on request |
| Additional weight per 10 mm stroke | Available on request |
| Pneumatic connection | G 1/8 |
| Piston rod thread | M10 × 1.25 |
Compressed air enters one of the two G 1/8 ports and drives the piston in a linear stroke. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position, so the load decelerates without hard impact — important on a 250 mm stroke where the rod mass is higher than on short-stroke variants. The cushioning screws remain accessible after mounting.
The piston rod is male-threaded M10 × 1.25. The profile barrel carries a magnetic piston and sensor slots for proximity switches.
Replacing a FESTO DNC-32-250-PPV-A? Check these five points before ordering the FESTO DSBC-32-250-PPVA-N3.
For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.
Not sure whether the 32 mm bore provides enough force at your supply pressure, or need the correct ISO 15552 mounting accessory for a 250 mm stroke? Send your load, cycle rate, supply pressure, and existing mounting accessory part number, and we will confirm the model code and accessory combination.
Q: What is the operating pressure range of the Festo DSBC-32-250-PPVA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].
Q: Is Festo DSBC-32-250-PPVA-N3 a direct replacement for DNC-32-250-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread G 1/8, stroke 250 mm, cushioning adjustment, mounting accessory, and force margin before release.
Q: What is the theoretical advance force at 6 bar?
A: Approximately 482 N at 6 bar, based on the 32 mm piston area. Confirm the actual load and duty cycle before sizing.
Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.
Q: What is the lead time for Festo DSBC-32-250-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.
Q: Can I get seal kits for the Festo DSBC-32-250-PPVA-N3?
A: Yes, on request. Provide the cylinder model and quantity, and we will confirm the matching seal kit.
For FESTO DSBC-32-250-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.