HYRIG can supply the FESTO DSBC-63-900-PPVA-N3 cylinder. The FESTO DSBC-63-900-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 63 mm piston diameter, 900 mm stroke, G 3/8 ports, and adjustable pneumatic cushioning at both ends. It is used on extra-long-stroke applications where a large bore is needed — heavy gate actuators, long-travel transfer carriages, and large diverter arms.
| Piston diameter | 63 mm |
| Stroke | 900 mm |
| Mode of operation | Double-acting |
| Cushioning | Pneumatic, adjustable at both ends (PPV) |
| Operating pressure | 0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4] |
| Ambient temperature | -20 °C … +80 °C |
| Port thread | G 3/8 |
| Piston rod thread | M16 × 1.5 |
| Standard | ISO 15552 |
Legacy reference: DNC-63-900-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series, while cushioning, sensing, ports, rod, and mounting options still require confirmation.
| Model | Bore | Stroke | Port | Cushioning |
|---|---|---|---|---|
| DSBC-63-25-PPVA-N3 | 63 mm | 25 mm | G 3/8 | Adjustable pneumatic, both ends |
| DSBC-63-50-PPVA-N3 | 63 mm | 50 mm | G 3/8 | Adjustable pneumatic, both ends |
| DSBC-63-100-PPVA-N3 | 63 mm | 100 mm | G 3/8 | Adjustable pneumatic, both ends |
| DSBC-63-200-PPVA-N3 | 63 mm | 200 mm | G 3/8 | Adjustable pneumatic, both ends |
| DSBC-63-900-PPVA-N3 | 63 mm | 900 mm | G 3/8 | Adjustable pneumatic, both ends |
Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Mounting standard | ISO 15552 |
| Mounting type | Via female thread or with accessories |
| Length at 900 mm stroke | Confirm against the FESTO datasheet |
| Width × height | 75 mm × 75 mm |
| Basic weight at 0 mm stroke | Available on request |
| Additional weight per 10 mm stroke | Available on request |
| Pneumatic connection | G 3/8 |
| Piston rod thread | M16 × 1.5 |
Compressed air enters one of the two G 3/8 ports and drives the piston in a linear stroke. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position, so the load decelerates without hard impact — critical on a 900 mm stroke where the moving mass is high and end-of-stroke impact would otherwise damage the load or the cylinder. The cushioning screws remain accessible after mounting.
The piston rod is male-threaded M16 × 1.5. The profile barrel carries a magnetic piston and sensor slots for proximity switches. On a 900 mm stroke, rod support or an external guide is strongly recommended to prevent rod bending; confirm the side-load conditions before ordering.
Replacing a FESTO DNC-63-900-PPV-A? Check these five points before ordering the FESTO DSBC-63-900-PPVA-N3.
For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.
Not sure whether the 63 mm bore provides enough force over a 900 mm stroke, or need the correct ISO 15552 mounting accessory and rod support? Send your load, side-load conditions, cycle rate, supply pressure, and existing mounting accessory part number, and we will confirm the model code and accessory combination.
Q: What is the operating pressure range of the Festo DSBC-63-900-PPVA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].
Q: Is Festo DSBC-63-900-PPVA-N3 a direct replacement for DNC-63-900-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread G 3/8, stroke 900 mm, cushioning adjustment, mounting accessory, force margin, and rod support before release.
Q: What is the theoretical advance force at 6 bar?
A: Approximately 1870 N at 6 bar, based on the 63 mm piston area. Confirm the actual load and side-load conditions before sizing.
Q: Does a 900 mm stroke need rod support?
A: Strongly recommended. At 900 mm stroke, the rod is exposed to buckling and side-load risk. An external guide or rod support is recommended for most applications — send the load details and we will confirm.
Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.
Q: What is the lead time for Festo DSBC-63-900-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.
For FESTO DSBC-63-900-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.