HYRIG can supply the FESTO DSBC-63-175-PPVA-N3 cylinder. The FESTO DSBC-63-175-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 63 mm piston diameter, 175 mm stroke, G 3/8 ports, and adjustable pneumatic cushioning at both ends. It is used where a 63 mm bore is needed for higher thrust (1870 N at 6 bar) but the machine envelope limits the stroke to 175 mm.
| Piston diameter | 63 mm |
| Stroke | 175 mm |
| Mode of operation | Double-acting |
| Cushioning | Pneumatic, adjustable at both ends (PPV) |
| Operating pressure | 0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4] |
| Ambient temperature | -20 °C … +80 °C |
| Theoretical force at 6 bar | 1870 N advance / 1682 N return |
| Port thread | G 3/8 |
| Piston rod thread | M16 × 1.5 |
| Standard | ISO 15552 |
Legacy reference: DNC-63-175-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series.
| Model | Bore | Stroke | Port | Cushioning | Theoretical force at 6 bar, advance |
|---|---|---|---|---|---|
| DSBC-63-100-PPVA-N3 | 63 mm | 100 mm | G 3/8 | Adjustable pneumatic, both ends | 1870 N |
| DSBC-63-125-PPVA-N3 | 63 mm | 125 mm | G 3/8 | Adjustable pneumatic, both ends | 1870 N |
| DSBC-63-160-PPVA-N3 | 63 mm | 160 mm | G 3/8 | Adjustable pneumatic, both ends | 1870 N |
| DSBC-63-175-PPVA-N3 | 63 mm | 175 mm | G 3/8 | Adjustable pneumatic, both ends | 1870 N |
| DSBC-63-200-PPVA-N3 | 63 mm | 200 mm | G 3/8 | Adjustable pneumatic, both ends | 1870 N |
Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Mounting standard | ISO 15552 |
| Length at 175 mm stroke | 368.1 mm |
| Width × height | 75 mm × 75 mm |
| Basic weight at 0 mm stroke | 1740 g |
| Additional weight per 10 mm stroke | 62 g |
| Net weight at 175 mm stroke | ≈ 2.83 kg |
| Cushioning length | 22 mm |
| Impact energy in end positions | 1.3 J |
| Pneumatic connection | G 3/8 |
| Piston rod thread | M16 × 1.5 |
Compressed air enters one of the two G 3/8 ports and drives the piston in a linear stroke. At 63 mm bore, the theoretical advance force at 6 bar is 1870 N, and the return force is 1682 N. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position, so the higher moving mass of a 63 mm cylinder decelerates without hard impact.
The piston rod is male-threaded M16 × 1.5. The profile barrel carries a magnetic piston and sensor slots for proximity switches. On a 175 mm stroke, side-load risk is moderate; an external guide is recommended only if the load attachment introduces lateral force.
Replacing a FESTO DNC-63-175-PPV-A? Check these five points before ordering the FESTO DSBC-63-175-PPVA-N3.
For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.
Not sure whether 1870 N at 6 bar is sufficient for your load, or need the matching ISO 15552 mounting accessory for a 175 mm stroke? Send your load, required force, cycle rate, and existing mounting accessory part number, and we will confirm the model code and accessory combination.
Q: What is the operating pressure range of the Festo DSBC-63-175-PPVA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].
Q: What is the theoretical force at 6 bar?
A: 1870 N advance and 1682 N return, based on the 63 mm piston area.
Q: Is Festo DSBC-63-175-PPVA-N3 a direct replacement for DNC-63-175-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread G 3/8, stroke 175 mm, cushioning adjustment, mounting accessory, and force margin before release.
Q: What is the net weight at 175 mm stroke?
A: Approximately 2.83 kg, calculated from 1740 g basic weight plus 62 g per 10 mm stroke. Exact weight may vary slightly with accessories.
Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.
Q: What is the lead time for Festo DSBC-63-175-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.
For FESTO DSBC-63-175-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.