Festo DSBC-100-260-PPVA-N3 Cylinder | 100 mm Bore 260 mm

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO DSBC-100-260-PPVA-N3 cylinder. The FESTO DSBC-100-260-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 100 mm piston diameter, 260 mm stroke, G 1/2 ports, and adjustable pneumatic cushioning at both ends. It is a large-bore, medium-stroke cylinder used where high thrust is needed over a 260 mm travel — heavy gate actuation, large press-fit stations, and high-force transfer slides.
Conatct For Details
DetailReview(0)Additional

Festo DSBC-100-260-PPVA-N3 Cylinder | 100 mm Bore 260 mm

HYRIG can supply the FESTO DSBC-100-260-PPVA-N3 cylinder. The FESTO DSBC-100-260-PPVA-N3 is a double-acting ISO 15552 profile cylinder with a 100 mm piston diameter, 260 mm stroke, G 1/2 ports, and adjustable pneumatic cushioning at both ends. It is a large-bore, medium-stroke cylinder used where high thrust is needed over a 260 mm travel — heavy gate actuation, large press-fit stations, and high-force transfer slides.

Key Facts



Piston diameter100 mm
Stroke260 mm
Mode of operationDouble-acting
CushioningPneumatic, adjustable at both ends (PPV)
Operating pressure0.6 bar … 12 bar at -20 °C to +80 °C, compressed air to ISO 8573-1:2010 [7:4:4]
Ambient temperature-20 °C … +80 °C
Port threadG 1/2
Piston rod threadM20 × 1.5
StandardISO 15552

Legacy reference: DNC-100-260-PPV-A (discontinued, replaced by this model). FESTO identifies DSBC as the successor to the DNC and DNCB series; ISO 15552 dimensions allow replacement of preceding series.

Festo DSBC-100 Model Specifications & Stroke Variants

ModelBoreStrokePortCushioning
DSBC-100-125-PPVA-N3100 mm125 mmG 1/2Adjustable pneumatic, both ends
DSBC-100-160-PPVA-N3100 mm160 mmG 1/2Adjustable pneumatic, both ends
DSBC-100-200-PPVA-N3100 mm200 mmG 1/2Adjustable pneumatic, both ends
DSBC-100-250-PPVA-N3100 mm250 mmG 1/2Adjustable pneumatic, both ends
DSBC-100-260-PPVA-N3100 mm260 mmG 1/2Adjustable pneumatic, both ends

Explore the full range in the FESTO DSBC ISO 15552 cylinder overview.

Data source: Technical data table.

Dimensions

ItemValue
Mounting standardISO 15552
Length at 260 mm strokeConfirm against the FESTO datasheet
Width × height110 mm × 110 mm
Basic weight at 0 mm strokeAvailable on request
Additional weight per 10 mm strokeAvailable on request
Pneumatic connectionG 1/2
Piston rod threadM20 × 1.5

Structure / Working Principle

Compressed air enters one of the two G 1/2 ports and drives the piston in a linear stroke. At 100 mm bore, the theoretical advance force at 6 bar is substantially higher than the 63 mm bore, making this cylinder suitable for heavy gates and press-fit stations. The adjustable pneumatic cushioning at both ends lets you tune exhaust air near end position, so the high moving mass decelerates without hard impact.

The piston rod is male-threaded M20 × 1.5. The profile barrel carries a magnetic piston and sensor slots for proximity switches. On a 260 mm stroke with a 100 mm bore, rod support or an external guide is recommended if the load attachment introduces side loads.

Cross-Reference & Replacement

Replacing a FESTO DNC-100-260-PPV-A? Check these five points before ordering the FESTO DSBC-100-260-PPVA-N3.

  1. Bore and stroke: 100 mm / 260 mm — match.
  2. Port thread: G 1/2 on both DNC and DSBC — match.
  3. Cushioning: DNC PPV-A and DSBC PPVA-N3 are both adjustable pneumatic cushioning at both ends. Confirm the cushioning screw position on the existing installation.
  4. Mounting interface: both follow ISO 15552. Reuse the existing female-thread mounting, or transfer the foot/flange accessory after confirming the accessory part number.
  5. Force and duty: confirm that the theoretical advance force at 6 bar matches the existing load and cycle rate, and check rod support requirements for the 260 mm stroke.

For a broader step-by-step checklist, see the FESTO DNC to DSBC replacement guide.

Applications

  • Heavy gate actuation: where the gate mass requires a 100 mm bore and the travel is 260 mm.
  • Large press-fit stations: where high thrust over a medium stroke is needed, and adjustable cushioning controls the end-of-stroke impact.
  • High-force transfer slides: where the ISO 15552 interface is already present and the load exceeds the capacity of smaller bores.
  • Replacement of DNC-100-260-PPV-A units: in existing machinery with ISO 15552 mounting.

Selection Support

Not sure whether a 100 mm bore provides enough force over a 260 mm stroke, or need the matching ISO 15552 mounting accessory and rod support? Send your load, side-load conditions, cycle rate, supply pressure, and existing mounting accessory part number, and we will confirm the model code and accessory combination.

Frequently Asked Questions

Q: What is the operating pressure range of the Festo DSBC-100-260-PPVA-N3?
A: 0.6 bar to 12 bar, at -20 °C to +80 °C, with compressed air to ISO 8573-1:2010 [7:4:4].

Q: Is Festo DSBC-100-260-PPVA-N3 a direct replacement for DNC-100-260-PPV-A?
A: Mechanically yes on the ISO 15552 interface, but verify port thread G 1/2, stroke 260 mm, cushioning adjustment, mounting accessory, force margin, and rod support before release.

Q: Does a 260 mm stroke with 100 mm bore need rod support?
A: It depends on the side load. For pure axial loads within the cylinder's rated buckling limit, no external support is needed. For side loads or long rod extensions, an external guide or rod support is recommended — send the load details and we will confirm.

Q: Does this Festo cylinder have a magnetic piston?
A: Yes. The DSBC series uses a magnetic piston, and the profile barrel has sensor slots for proximity switches.

Q: What is the lead time for Festo DSBC-100-260-PPVA-N3?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.

Contact

For FESTO DSBC-100-260-PPVA-N3 selection, replacement verification, and seal kits, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit