HYRIG can supply the FESTO NPQM-D-Q4-E-P10 push-in fitting. The FESTO NPQM-D-Q4-E-P10 is a straight inline push-in connector for 4 mm outer-diameter tubing, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body. It is used in compressed air, vacuum, and water circuits where a solid-metal fitting is preferred over a polymer body.
| Fitting type | Straight inline push-in connector |
| Tube connection | 4 mm OD × 4 mm OD |
| Operating pressure | -0.95 bar … +16 bar across the full temperature range |
| Ambient temperature | -20 °C … +70 °C |
| Nominal size | 3 mm |
| Body material | Nickel-plated brass |
| Seal material | NBR |
| Design | Push-pull |
| Order code | 558760 |
| Model | Tube OD | Nominal size | Pressure range | Order code |
|---|---|---|---|---|
| NPQM-D-Q4-E-P10 | 4 mm | 3 mm | -0.95 … 16 bar | 558760 |
| NPQM-D-Q6-E-P10 | 6 mm | 5 mm | -0.95 … 16 bar | 558761 |
| NPQM-D-Q8-E-P10 | 8 mm | 7 mm | -0.95 … 16 bar | 558762 |
| NPQM-D-Q10-E-P10 | 10 mm | 9 mm | -0.95 … 16 bar | 558763 |
Explore the full range in the FESTO NPQM push-in fitting overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Connection type | Push-in, 4 mm tube |
| Nominal size | 3 mm |
| Body material | Nickel-plated brass |
| Seal material | NBR |
| Operating temperature | -20 °C … +70 °C |
| Media | Compressed air, vacuum, water |
The NPQM-D series uses a push-pull release sleeve: insert the tubing until it bottoms out, and the internal collet grips the tube OD; pull the release sleeve to remove the tube. The nickel-plated brass body resists corrosion in workshop air and light water exposure, and the NBR seal provides a tight joint across the -0.95 to 16 bar range.
Compared with polymer-body push-in fittings, the solid-metal NPQM body is more resistant to accidental impact and higher temperature spikes, but it is heavier and not suitable for every mobile pneumatic application. Confirm the fitting weight and vibration exposure if the circuit is mounted on a moving machine part.
Not sure whether the 4 mm NPQM-D is the correct tube size for your circuit, or need the matching 6 mm or 8 mm variant? Send your tube OD, operating pressure, media, and temperature range, and we will confirm the fitting model and pack quantity.
Q: What is the pressure range of the Festo NPQM-D-Q4-E-P10?
A: -0.95 bar to 16 bar across the full temperature range of -20 °C to +70 °C.
Q: Is NPQM-D-Q4-E-P10 suitable for vacuum?
A: Yes. The lower pressure limit is -0.95 bar, which covers typical vacuum pick-and-place and vacuum generation circuits.
Q: What is the difference between NPQM and QS fittings?
A: NPQM uses a solid nickel-plated brass body and a push-pull release sleeve, rated to 16 bar. QS is a polymer-body push-in fitting series with a different release mechanism and a lower pressure rating. Choose NPQM when you need a metal body and higher pressure resistance; choose QS when weight and cost are the primary constraints.
Q: How is the fitting sold — individually or in packs?
A: The NPQM-D-Q4-E-P10 is typically supplied in multiples of 10. Confirm the pack quantity with HYRIG before ordering.
Q: What is the lead time for Festo NPQM-D-Q4-E-P10?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.
For FESTO NPQM-D-Q4-E-P10 selection and pack quantities, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.