Festo NPQM-D-Q8-E-P10 Push-in Fitting | 8 mm Tube, 16 bar

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO NPQM-D-Q8-E-P10 push-in fitting. The FESTO NPQM-D-Q8-E-P10 is a straight inline push-in connector for 8 mm outer-diameter tubing, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body. It is the most common NPQM size for main air lines and actuator ports where an 8 mm tube is used.
Conatct For Details
DetailReview(0)Additional

Festo NPQM-D-Q8-E-P10 Push-in Fitting | 8 mm Tube, 16 bar

HYRIG can supply the FESTO NPQM-D-Q8-E-P10 push-in fitting. The FESTO NPQM-D-Q8-E-P10 is a straight inline push-in connector for 8 mm outer-diameter tubing, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body. It is the most common NPQM size for main air lines and actuator ports where an 8 mm tube is used.

Key Facts



Fitting typeStraight inline push-in connector
Tube connection8 mm OD × 8 mm OD
Operating pressure-0.95 bar … +16 bar across the full temperature range
Ambient temperature-20 °C … +70 °C
Nominal size7 mm
Body materialNickel-plated brass
Seal materialNBR
DesignPush-pull
Order code558762

Festo NPQM-D Model Specifications & Tube Size Variants

ModelTube ODNominal sizePressure rangeOrder code
NPQM-D-Q4-E-P104 mm3 mm-0.95 … 16 bar558760
NPQM-D-Q6-E-P106 mm5 mm-0.95 … 16 bar558761
NPQM-D-Q8-E-P108 mm7 mm-0.95 … 16 bar558762
NPQM-D-Q10-E-P1010 mm9 mm-0.95 … 16 bar558763

Explore the full range in the FESTO NPQM push-in fitting overview.

Data source: Technical data table.

Dimensions

ItemValue
Connection typePush-in, 8 mm tube
Nominal size7 mm
Body materialNickel-plated brass
Seal materialNBR
Operating temperature-20 °C … +70 °C
MediaCompressed air, vacuum, water

Structure / Working Principle

The NPQM-D series uses a push-pull release sleeve: insert the tubing until it bottoms out, and the internal collet grips the tube OD; pull the release sleeve to remove the tube. The 8 mm size uses a 7 mm nominal bore, which keeps pressure drop low on main air lines and actuator supply ports.

The nickel-plated brass body resists corrosion in workshop air and light water exposure, and the NBR seal provides a tight joint across the -0.95 to 16 bar range. Compared with the 4 mm and 6 mm NPQM sizes, the 8 mm body has a larger release sleeve and higher pull-out force — confirm the tube insertion depth and the release clearance in tight panel layouts.

Applications

  • Main air lines: 8 mm tubing runs from the FRL unit or valve terminal to actuator banks, where a 7 mm nominal bore keeps pressure drop low.
  • Actuator ports: cylinder ports on DSBC and ADN series cylinders where the port thread is G 1/4 and the tube OD is 8 mm.
  • Vacuum lines: 8 mm vacuum runs for larger pick-and-place cups and vacuum generators.
  • Water circuits: the nickel-plated brass body and NBR seal support light water exposure, but confirm water quality and temperature before use.

Selection Support

Not sure whether the 8 mm NPQM-D is the correct tube size for your circuit, or need the matching 6 mm or 10 mm variant? Send your tube OD, operating pressure, media, and temperature range, and we will confirm the fitting model and pack quantity.

Frequently Asked Questions

Q: What is the pressure range of the Festo NPQM-D-Q8-E-P10?
A: -0.95 bar to 16 bar across the full temperature range of -20 °C to +70 °C.

Q: What is the nominal size of the 8 mm NPQM-D?
A: 7 mm. The nominal size determines the flow cross-section, not the tube outside diameter.

Q: Is NPQM-D-Q8-E-P10 suitable for vacuum?
A: Yes. The lower pressure limit is -0.95 bar, which covers typical vacuum pick-and-place and vacuum generation circuits.

Q: What is the difference between NPQM and QS fittings?
A: NPQM uses a solid nickel-plated brass body and a push-pull release sleeve, rated to 16 bar. QS is a polymer-body push-in fitting series with a different release mechanism and a lower pressure rating. Choose NPQM when you need a metal body and higher pressure resistance.

Q: How is the fitting sold — individually or in packs?
A: The NPQM-D-Q8-E-P10 is typically supplied in multiples of 10. Confirm the pack quantity with HYRIG before ordering.

Q: What is the lead time for Festo NPQM-D-Q8-E-P10?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.

Contact

For FESTO NPQM-D-Q8-E-P10 selection and pack quantities, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit