HYRIG can supply the FESTO NPQM-D-Q6-E-P10 push-in fitting. The FESTO NPQM-D-Q6-E-P10 is a straight inline push-in connector for 6 mm outer-diameter tubing, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body and 5 mm nominal bore. It is used in compressed air and vacuum circuits where a metal body is preferred over a polymer fitting, and the 6 mm tube size matches the pilot lines on most pneumatic valves and small cylinders.
| Fitting type | Straight inline push-in connector |
| Tube connection | 6 mm OD × 6 mm OD |
| Operating pressure | -0.95 bar … +16 bar across the full temperature range |
| Ambient temperature | -20 °C … +70 °C |
| Nominal size | 5 mm |
| Body material | Nickel-plated brass |
| Seal material | NBR |
| Design | Push-pull |
| Weight | 15 g |
| Order code | 558761 |
| Model | Tube OD | Nominal size | Pressure range | Order code |
|---|---|---|---|---|
| NPQM-D-Q4-E-P10 | 4 mm | 3 mm | -0.95 … 16 bar | 558760 |
| NPQM-D-Q6-E-P10 | 6 mm | 5 mm | -0.95 … 16 bar | 558761 |
| NPQM-D-Q8-E-P10 | 8 mm | 7 mm | -0.95 … 16 bar | 558762 |
| NPQM-D-Q10-E-P10 | 10 mm | 9 mm | -0.95 … 16 bar | 558763 |
Explore the full range in the FESTO NPQM push-in fitting overview.
Data source: Technical data table.
| Item | Value |
|---|---|
| Connection type | Push-in, 6 mm tube |
| Nominal size | 5 mm |
| Body material | Nickel-plated brass |
| Seal material | NBR |
| Weight | 15 g |
| Operating temperature | -20 °C … +70 °C |
| Media | Compressed air, vacuum, water |
The NPQM-D series uses a push-pull release sleeve: insert the tubing until it bottoms out, and the internal collet grips the tube OD; pull the release sleeve to remove the tube. The 6 mm size uses a 5 mm nominal bore, which is the most common pilot line size on VSVA and VUVG valves and on ADN compact cylinders.
The nickel-plated brass body resists corrosion in workshop air and light water exposure, and the NBR seal provides a tight joint across the -0.95 to 16 bar range. Compared with the 4 mm NPQM size, the 6 mm body has a larger release sleeve and higher pull-out force; confirm the tube insertion depth and the release clearance in dense valve terminal layouts.
Not sure whether the 6 mm NPQM-D is the correct tube size for your pilot circuit, or need the matching 4 mm or 8 mm variant? Send your tube OD, operating pressure, media, and temperature range, and we will confirm the fitting model and pack quantity.
Q: What is the pressure range of the Festo NPQM-D-Q6-E-P10?
A: -0.95 bar to 16 bar across the full temperature range of -20 °C to +70 °C.
Q: What is the nominal size of the 6 mm NPQM-D?
A: 5 mm. The nominal size determines the flow cross-section, not the tube outside diameter.
Q: Is NPQM-D-Q6-E-P10 suitable for vacuum?
A: Yes. The lower pressure limit is -0.95 bar, which covers typical vacuum pick-and-place and vacuum generation circuits.
Q: What is the difference between NPQM and QS fittings?
A: NPQM uses a solid nickel-plated brass body and a push-pull release sleeve, rated to 16 bar. QS is a polymer-body push-in fitting series with a different release mechanism and a lower pressure rating. Choose NPQM when you need a metal body and higher pressure resistance.
Q: How is the fitting sold — individually or in packs?
A: The NPQM-D-Q6-E-P10 is typically supplied in multiples of 10. Confirm the pack quantity with HYRIG before ordering.
Q: What is the lead time for Festo NPQM-D-Q6-E-P10?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.
For FESTO NPQM-D-Q6-E-P10 selection and pack quantities, contact HYRIG: info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.