Festo NPQM-D-Q10-E-P10 Push-in Fitting | 10 mm Tube, 16 bar

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO NPQM-D-Q10-E-P10 push-in fitting. The FESTO NPQM-D-Q10-E-P10 is a straight inline push-in connector for 10 mm outer-diameter tubing, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body and 9 mm nominal bore. It is used on main air lines and actuator supply ports where a 10 mm tube is required for higher flow, and the 9 mm nominal bore keeps pressure drop low on long runs.
Conatct For Details
DetailReview(0)Additional

Festo NPQM-D-Q10-E-P10 Push-in Fitting | 10 mm Tube, 16 bar

HYRIG can supply the FESTO NPQM-D-Q10-E-P10 push-in fitting. The FESTO NPQM-D-Q10-E-P10 is a straight inline push-in connector for 10 mm outer-diameter tubing, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body and 9 mm nominal bore. It is used on main air lines and actuator supply ports where a 10 mm tube is required for higher flow, and the 9 mm nominal bore keeps pressure drop low on long runs.

Key Facts



Fitting typeStraight inline push-in connector
Tube connection10 mm OD × 10 mm OD
Operating pressure-0.95 bar … +16 bar across the full temperature range
Ambient temperature-20 °C … +70 °C
Nominal size9 mm
Body materialNickel-plated brass
Seal materialNBR
DesignPush-pull
Order code558763

Festo NPQM-D Model Specifications & Tube Size Variants

ModelTube ODNominal sizePressure rangeOrder code
NPQM-D-Q4-E-P104 mm3 mm-0.95 … 16 bar558760
NPQM-D-Q6-E-P106 mm5 mm-0.95 … 16 bar558761
NPQM-D-Q8-E-P108 mm7 mm-0.95 … 16 bar558762
NPQM-D-Q10-E-P1010 mm9 mm-0.95 … 16 bar558763

Explore the full range in the FESTO NPQM push-in fitting overview.

Data source: Technical data table.

Dimensions

ItemValue
Connection typePush-in, 10 mm tube
Nominal size9 mm
Body materialNickel-plated brass
Seal materialNBR
Operating temperature-20 °C … +70 °C
MediaCompressed air, vacuum, water

Structure / Working Principle

The NPQM-D series uses a push-pull release sleeve: insert the tubing until it bottoms out, and the internal collet grips the tube OD; pull the release sleeve to remove the tube. The 10 mm size uses a 9 mm nominal bore, which is the largest in the NPQM-D inline range and is used where flow capacity matters more than fitting weight.

The nickel-plated brass body resists corrosion in workshop air and light water exposure, and the NBR seal provides a tight joint across the -0.95 to 16 bar range. Compared with the 8 mm NPQM size, the 10 mm body has a larger release sleeve and higher pull-out force; confirm the tube insertion depth and the release clearance in dense panel layouts.

Applications

  • Main air lines: 10 mm tubing from the FRL unit or valve terminal to actuator banks, where a 9 mm nominal bore keeps pressure drop low on long runs.
  • Actuator supply ports: DSBC-63 and DSBC-80 cylinders where the port thread is G 3/8 and the tube OD is 10 mm.
  • Vacuum lines: 10 mm vacuum runs for larger pick-and-place cups and high-flow vacuum generators.
  • Water circuits: the nickel-plated brass body and NBR seal support light water exposure, but confirm water quality and temperature before use.

Selection Support

Not sure whether the 10 mm NPQM-D is the correct tube size for your flow requirement, or need the matching 8 mm or 12 mm variant? Send your tube OD, operating pressure, flow requirement, and temperature range, and we will confirm the fitting model and pack quantity.

Frequently Asked Questions

Q: What is the pressure range of the Festo NPQM-D-Q10-E-P10?
A: -0.95 bar to 16 bar across the full temperature range of -20 °C to +70 °C.

Q: What is the nominal size of the 10 mm NPQM-D?
A: 9 mm. The nominal size determines the flow cross-section, not the tube outside diameter.

Q: Is NPQM-D-Q10-E-P10 suitable for vacuum?
A: Yes. The lower pressure limit is -0.95 bar, which covers typical vacuum pick-and-place and vacuum generation circuits.

Q: What is the difference between NPQM and QS fittings?
A: NPQM uses a solid nickel-plated brass body and a push-pull release sleeve, rated to 16 bar. QS is a polymer-body push-in fitting series with a different release mechanism and a lower pressure rating. Choose NPQM when you need a metal body and higher pressure resistance.

Q: How is the fitting sold — individually or in packs?
A: The NPQM-D-Q10-E-P10 is typically supplied in multiples of 10. Confirm the pack quantity with HYRIG before ordering.

Q: What is the lead time for Festo NPQM-D-Q10-E-P10?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.

Contact

For FESTO NPQM-D-Q10-E-P10 selection and pack quantities, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit