Festo NPQM-T-Q8-E-P10 Push-in Tee | 8 mm Tube, 16 bar

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO NPQM-T-Q8-E-P10 push-in tee. The FESTO NPQM-T-Q8-E-P10 is a T-shaped push-in connector with one 8 mm inlet and two 8 mm outlets, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body and 7 mm nominal bore. It is used to split a main 8 mm air line into two branches at the point of use, keeping the flow capacity of the parent line on both outlets.
Conatct For Details
DetailReview(0)Additional

Festo NPQM-T-Q8-E-P10 Push-in Tee | 8 mm Tube, 16 bar

HYRIG can supply the FESTO NPQM-T-Q8-E-P10 push-in tee. The FESTO NPQM-T-Q8-E-P10 is a T-shaped push-in connector with one 8 mm inlet and two 8 mm outlets, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body and 7 mm nominal bore. It is used to split a main 8 mm air line into two branches at the point of use, keeping the flow capacity of the parent line on both outlets.

Key Facts



Fitting typeT-shaped push-in connector (1 inlet + 2 outlets)
Tube connection8 mm OD × 8 mm OD × 8 mm OD
Operating pressure-0.95 bar … +16 bar across the full temperature range
Ambient temperature-20 °C … +70 °C
Nominal size7 mm (each branch)
Body materialNickel-plated brass
Seal materialNBR
DesignPush-pull
Order code558788

Festo NPQM-T Model Specifications & Tube Size Variants

ModelTube ODNominal sizePressure rangeOrder code
NPQM-T-Q4-E-P104 mm3 mm-0.95 … 16 bar558785
NPQM-T-Q6-E-P106 mm5 mm-0.95 … 16 bar558787
NPQM-T-Q8-E-P108 mm7 mm-0.95 … 16 bar558788
NPQM-T-Q10-E-P1010 mm9 mm-0.95 … 16 bar558789

Explore the full range in the FESTO NPQM push-in fitting overview.

Data source: Technical data table.

Dimensions

ItemValue
Connection typePush-in, 8 mm tube, T-shaped
Nominal size7 mm
Body materialNickel-plated brass
Seal materialNBR
Operating temperature-20 °C … +70 °C
MediaCompressed air, vacuum, water

Structure / Working Principle

The NPQM-T series uses a push-pull release sleeve on each of the three ports: one inlet and two outlets. Insert the tubing until it bottoms out on each port; pull the release sleeve to remove. The T-body is machined from nickel-plated brass, so the two outlets branch at 90° to the inlet without an additional manifold.

The 8 mm size uses a 7 mm nominal bore on each branch, matching the flow capacity of the NPQM-D-Q8 straight connector. Compared with using two separate straight connectors and a brass tee, the one-piece NPQM-T body reduces assembly time and leak points — but confirm the overall length and outlet spacing fit the available space at the branch point.

Applications

  • Splitting main air lines: one 8 mm supply line feeding two valve terminals or two actuator banks, where both branches need the full 7 mm nominal bore.
  • Actuator supply at the point of use: splitting an 8 mm line to two DSBC-40 or DSBC-50 cylinders mounted side by side.
  • Vacuum distribution: one 8 mm vacuum line branching to two larger suction cups or two vacuum ejectors.
  • Water circuits: the nickel-plated brass body and NBR seal support light water exposure; confirm water quality and temperature before use.

Selection Support

Not sure whether the T-port layout fits your branch point, or need the matching straight and elbow variants? Send your tube OD, branch flow requirement, available space, and port orientation, and we will confirm the fitting model and pack quantity.

Frequently Asked Questions

Q: What is the pressure range of the Festo NPQM-T-Q8-E-P10?
A: -0.95 bar to 16 bar across the full temperature range of -20 °C to +70 °C.

Q: What is the nominal size of the 8 mm NPQM-T?
A: 7 mm on each branch. The nominal size determines the flow cross-section, not the tube outside diameter.

Q: What is the difference between NPQM-T and NPQM-D?
A: NPQM-D is a straight 1-to-1 connector; NPQM-T is a T-shaped 1-to-2 splitter. Both use the same push-pull release sleeve and the same -0.95 to 16 bar pressure range. Choose NPQM-T when you need to branch a line at the point of use.

Q: Does the NPQM-T-Q8-E-P10 maintain full flow on both outlets?
A: Each branch has a 7 mm nominal bore, matching the NPQM-D-Q8 straight connector. The total flow is split between the two outlets, so the pressure at each outlet depends on the downstream demand and line length.

Q: How is the fitting sold — individually or in packs?
A: The NPQM-T-Q8-E-P10 is typically supplied in multiples of 10. Confirm the pack quantity with HYRIG before ordering.

Q: What is the lead time for Festo NPQM-T-Q8-E-P10?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.

Contact

For FESTO NPQM-T-Q8-E-P10 selection and pack quantities, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit