Festo NPQM-L-Q8-E-P10 Push-in Elbow | 8 mm Tube, 16 bar

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
HYRIG can supply the FESTO NPQM-L-Q8-E-P10 push-in elbow. The FESTO NPQM-L-Q8-E-P10 is a 90° push-in elbow connector for 8 mm outer-diameter tubing, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body and 7 mm nominal bore. It is used where the tubing needs to turn 90° at the cylinder port or valve terminal without a separate elbow adapter, and the metal body resists impact in dense panel layouts.
Conatct For Details
DetailReview(0)Additional

Festo NPQM-L-Q8-E-P10 Push-in Elbow | 8 mm Tube, 16 bar

HYRIG can supply the FESTO NPQM-L-Q8-E-P10 push-in elbow. The FESTO NPQM-L-Q8-E-P10 is a 90° push-in elbow connector for 8 mm outer-diameter tubing, rated from -0.95 bar vacuum to 16 bar, with a nickel-plated brass body and 7 mm nominal bore. It is used where the tubing needs to turn 90° at the cylinder port or valve terminal without a separate elbow adapter, and the metal body resists impact in dense panel layouts.

Key Facts



Fitting type90° push-in elbow connector
Tube connection8 mm OD × 8 mm OD
Operating pressure-0.95 bar … +16 bar across the full temperature range
Ambient temperature-20 °C … +70 °C
Nominal size7 mm
Body materialNickel-plated brass
Seal materialNBR
DesignPush-pull
Weight22 g
Order code558778

Festo NPQM-L Model Specifications & Tube Size Variants

ModelTube ODNominal sizePressure rangeOrder code
NPQM-L-Q4-E-P104 mm3 mm-0.95 … 16 bar558776
NPQM-L-Q6-E-P106 mm5 mm-0.95 … 16 bar558777
NPQM-L-Q8-E-P108 mm7 mm-0.95 … 16 bar558778
NPQM-L-Q10-E-P1010 mm9 mm-0.95 … 16 bar558779

Explore the full range in the FESTO NPQM push-in fitting overview.

Data source: Technical data table.

Dimensions

ItemValue
Connection typePush-in, 8 mm tube, 90° elbow
Nominal size7 mm
Body materialNickel-plated brass
Seal materialNBR
Weight22 g
Operating temperature-20 °C … +70 °C
MediaCompressed air, vacuum, water

Structure / Working Principle

The NPQM-L series uses a push-pull release sleeve on both the inlet and outlet ports. Insert the tubing until it bottoms out; pull the release sleeve to remove. The 90° elbow body is machined from nickel-plated brass, so the tube exits at a right angle to the port without an additional adapter.

The 8 mm size uses a 7 mm nominal bore, matching the flow capacity of the NPQM-D-Q8 straight connector. The metal elbow body is heavier than a polymer elbow (22 g vs ~8–10 g), but it resists impact and does not creep under sustained side load — important when the tubing is routed tightly against a machine frame.

Applications

  • Cylinder port connections: DSBC and ADN cylinders where the port faces a machine frame and the tubing must turn 90° immediately after the fitting.
  • Valve terminal outlets: VSVA and VUVG valve terminals where the outlet ports are close together and a straight fitting would interfere with the adjacent port.
  • Dense panel layouts: where tubing runs along the panel surface and a 90° turn keeps the bundle tight against the frame.
  • Vacuum and water circuits: the metal body and NBR seal support -0.95 bar vacuum and light water exposure; confirm media compatibility before use.

Selection Support

Not sure whether the NPQM-L elbow is the correct angle for your port layout, or need the matching NPQM-D straight variant? Send your port thread, tube OD, routing direction, and space constraints, and we will confirm the fitting model and pack quantity.

Frequently Asked Questions

Q: What is the pressure range of the Festo NPQM-L-Q8-E-P10?
A: -0.95 bar to 16 bar across the full temperature range of -20 °C to +70 °C.

Q: What is the nominal size of the 8 mm NPQM-L elbow?
A: 7 mm. The nominal size determines the flow cross-section, not the tube outside diameter.

Q: What is the difference between NPQM-D and NPQM-L?
A: NPQM-D is a straight inline connector; NPQM-L is a 90° elbow. Both use the same push-pull release sleeve and the same -0.95 to 16 bar pressure range. Choose NPQM-L when the tubing needs to turn 90° at the port; choose NPQM-D when a straight run is possible.

Q: Is the NPQM-L-Q8-E-P10 heavier than a polymer elbow?
A: Yes. The nickel-plated brass body weighs approximately 22 g, compared with roughly 8–10 g for a polymer elbow. The added weight is usually negligible for fixed installations, but confirm if the fitting is mounted on a moving machine part.

Q: How is the fitting sold — individually or in packs?
A: The NPQM-L-Q8-E-P10 is typically supplied in multiples of 10. Confirm the pack quantity with HYRIG before ordering.

Q: What is the lead time for Festo NPQM-L-Q8-E-P10?
A: Standard lead time is 2–3 weeks from order confirmation, based on the quoted supply status.

Contact

For FESTO NPQM-L-Q8-E-P10 selection and pack quantities, contact HYRIG: info@hyrig.com.

Related Pages

Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit