Lean Amine Charge Pump – API 610 OH2 / BB3 / VS4

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 lean amine charge pump for gas sweetening and refinery H₂S/CO₂ removal systems. Available in OH2 single-stage overhung, BB3 axially split multistage, and VS4 vertical suspended configurations. 316L stainless steel wetted parts (API 610 S-8), API 682 dual mechanical seals with Plan 53B for emission control. Provides reliable, high-pressure feed of regenerated lean amine from stripper to absorber.

Conatct For Details
DetailReview(0)Additional

Product Overview

The Lean Amine Charge Pump is a critical piece of rotating equipment in amine sweetening units, responsible for conveying regenerated lean amine from the stripper (regenerator) to the high-pressure absorber. As acid gases such as H₂S and CO₂ are removed from the sour gas stream, lean amine is regenerated and pressurised by these pumps to re-enter the absorption cycle. All pumps are engineered to meet API 610 11th/12th edition (ISO 13709) standards, ensuring 3-year uninterrupted operation and a 20-year service life.

Key Pump Configurations (OH2 / BB3 / VS4)

Pump TypeConstructionBest Application for Lean Amine
OH2Overhung, centerline-mounted, single-stageModerate flow (<600 m³/h) and moderate head requirements; compact footprint, easy seal maintenance
BB3Axially split, multistage, between bearingsHigh-head, high-pressure lean amine charge (head up to 1,600 m); refinery HP amine circulation; preferred by 60% of global gas plant designs
VS4Vertical suspended, sump/can typeLean amine transfer from storage or sump; space-constrained installations; fire-code compliance (zero shaft penetration)

BB3 configuration—such as the DVMX series—offers 4 to 14 stages in heavy-duty double volute casings, supporting flows to 600 m³/h, heads to 1,300 m, and temperatures from –40°C to +210°C with opposed impeller for axial thrust self-balancing.

Lean Amine vs. Rich Amine – Key Differences

Lean amine is the regenerated solvent stripped of H₂S and CO₂, returning from the stripper bottom to the absorber. Rich amine is the acid-gas-loaded solution leaving the absorber.

ParameterLean Amine Charge PumpRich Amine Pump
Service temperature40–120°C40–60°C
Corrosivity (CO₂/H₂S)25–40% of rich amine (but hot)High (fully saturated)
Operating pressureUp to 100 barg (discharge)Moderate suction, low discharge (3–6 barg after let-down)

Mechanical Seals – API 682 Compliance

Sealing ConfigurationAPI PlanApplication
Dual pressurized seal (Arrangement 3)Plan 53B (bladder accumulator–pressurised barrier fluid)High-pressure lean amine; BP and TotalEnergies mandate this for onshore amine service
Tandem seal with buffer fluidPlan 52Medium-pressure lean amine; common in SE Asian plants
Single sealPlan 11/21Only for low-pressure, non-hazardous lean amine (discontinued by leading EPCs for HSE compliance)

For high-pressure/hazardous service, Plan 53B provides barrier fluid pressurised by a bladder accumulator—higher pressure than Plan 53A, eliminates N₂ entrainment, and prevents emission of amine vapour.

Material Selection – API 610 Table H

ComponentRecommended MaterialAPI 610 ClassRemarks
Casing, impeller, wear rings316L stainless steelS-8Corrosion resistance; contains Mo (2–3%) for Cl⁻ pitting resistance
Shaft4140 / 316 SS (≤400°C)C-6 / A-8Nitrided shaft preferred for wear resistance
NACE MR0175For H₂S-containing amine chargeS-8 or D-1Mandatory for lean amine with residual H₂S

Lean amine at elevated temperature (≥80°C) becomes increasingly aggressive. Carbon steel has been proven inadequate—over 90% of plants that started with carbon steel have upgraded to 316SS after pitting failures.

API 610 Compliance Highlights for Lean Amine Charge

  • Axial thrust balance (BB3): Back-to-back opposed impellers self-balance axial thrust, eliminating complex balance drums or discs that can foul in amine service.

  • Radial thrust balance: Double volute casing at each stage balances radial thrust, minimising shaft deflection and extending bearing life beyond API 610 minimum 25,000 hours.

  • Seal chamber: API 682 compliant, accommodating single, tandem or double cartridge seals without modification.

  • Inlet design: Large suction eye on first-stage impeller reduces NPSHr; when calculating NPSHa for lean amine, do not consider subcooling—the fluid must be considered at bubble point at the pump suction flange to avoid cavitation.

  • Flange arrangement (BB3): On lower casing half, allowing full rotor inspection without disturbing piping.

Lean Amine Charge Pump Performance Range

ParameterOH2 (Single‑Stage)BB3 (Multi‑Stage)VS4 (Sump)
Flow range30–600 m³/h50–1,600 m³/h5–300 m³/h
Head range30–250 m100–1,600 m10–180 m
Pressure ratingUp to 4.0 MPaUp to 25 MPaUp to 2.5 MPa
Temperature–45°C to +260°C–80°C to +200°C–45°C to +120°C
Motor powerUp to 315 kWUp to 5 MWUp to 110 kW

Actual performance curves are available upon request; derating is required for elevated amine viscosity and density variations.

Freeze Protection – A Critical Consideration

Lean amine has a high freezing point. For plants operating at low ambient temperatures:

  • Steam tracing—commonly used—can create local hot spots that accelerate corrosion.

  • Electric tracing is strongly preferred for freeze protection without driving corrosion problems.

  • Absence of freeze protection has led to catastrophic pump casing fractures in multiple North American winter incidents.

Power Recovery Integration (PRT)

Modern lean amine charge pumps are increasingly integrated with Power Recovery Turbines (PRT). The rich amine enters from the absorber at high pressure (50–100 barg) and flows through a PRT mechanically coupled to the lean amine charge pump driver, reducing motor power draw by up to 1,500 kW per unit.

Why Choose Our Lean Amine Charge Pump?

  • Full API 610 compliance (8th/11th/12th edition)—OH2, BB3, VS4

  • 316L SS (S-8) wetted parts—field-validated for 20-year amine service

  • API 682 dual seals with Plan 53B—zero process emissions; barrier fluid pressure independently monitored

  • BB3 opposed impellers—axial thrust self-balanced, no thrust-bearing overload

  • Double volute casing—radial loads cancelled, bearing life extended

  • Integration-ready—PRT coupling provisions and NACE MR0175 material options

  • Loss of flow detection—Proprietary low-flow bypass recirculation valve prevents dead-head runout in fluctuating absorber demand

Applications

  • Natural gas sweetening (amine treating for pipeline gas)

  • Refinery hydrodesulfurisation (HDS) and Claus tail-gas treatment

  • LNG feed gas pretreatment

  • Syngas purification (ammonia and methanol plants)

  • CO₂ capture (CCUS) units

Get a Quote or Engineering Support

For detailed pump selection, hydraulic analysis, API 610 data sheets, or a complete lean amine charge pump package—including PRT integration—please contact our engineering team.

Email: info@hyrig.com


*All performance data and engineering recommendations are based on API 610 11th/12th edition standards and align with current best practices for lean amine charge pumps in HP refinery and gas processing service.*


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit