The Propylene Condensate Water Pump OH2 is a heavy duty, API 610 (ISO 13709) Type OH2 horizontal overhung centrifugal pump specifically engineered for handling condensate water containing trace propylene, propane, and other light hydrocarbons in propylene production units, propane dehydrogenation (PDH) plants, olefins facilities, and refineries. It reliably pumps condensate from steam condensate pots, phase separators, knockout drums, and heat exchanger drains to collection systems, cooling towers, or further treatment.
Key Performance Parameters (Typical for Propylene Condensate Service)
Flow range: 10 – 350 m³/h (depending on plant condensate load)
Head range: Up to 130 m (approximately 425 ft)
Speed: 1,450/1,750 RPM or 2,950/3,550 RPM
Power range: 5.5 – 110 kW (varies with flow, head, and fluid density)
Process Compatibility (Propylene Condensate Service)
Temperature range: 10°C to 95°C (50°F to 203°F) – typical for warm condensate from propylene processes.
Design pressure: Up to 25 bar (363 psi) – suitable for higher pressure condensate systems in PDH units.
Media handled: Condensate water with trace propylene, propane, light hydrocarbons, steam condensate, and water/hydrocarbon mixtures.
Wetted materials: Carbon steel (S-1) – standard; 316 stainless steel (S-6) recommended for higher corrosion resistance or where chloride/hydrocarbon interactions may occur; duplex (S-8) optional for sour service.
Reliability & Efficiency
Sealing system: Mechanical seal (single or double cartridge) with API flush plans – typically Plan 11 (internal recirculation) or Plan 21 (cooling). Double seal (Plan 52/53) strongly recommended for hydrocarbon service to prevent fugitive emissions.
Hydraulic efficiency: ≥72% at best efficiency point (BEP)
NPSHr: ≤4.0 m – low NPSH design for condensate service with limited suction head.
MTBF: ≥8000 hours – supports continuous plant operation.
Mechanical Design (API 610 OH2 Features for Propylene Condensate Service)
Configuration: Single stage, overhung, horizontal, centerline mounted (optional foot mounted for lower temperatures), radially split casing.
Inlet/Outlet: Suction 2″–6″, discharge 1.5″–4″ (customizable based on flow)
Flange rating: Class 150 or Class 300 RF (ANSI/ASME)
Design standard: API 610 11th/12th edition (ISO 13709) – full compliance.
Rotor support: Rigid shaft with minimal deflection – extends mechanical seal and bearing life.
Bearing housing: Fan cooled (standard); water cooling optional for higher temperatures.
Seal chamber: API 682 compliant, sized for cartridge mechanical seals (large bore recommended).
Maintenance: Back pull-out design – pump internals removable without disturbing suction/discharge piping or driver.
Impeller: Closed radial, dynamically balanced, with renewable wear rings.
Wear rings: Renewable casing and impeller wear rings (hard coated options available) to maintain hydraulic efficiency.
Why Choose This OH2 Propylene Condensate Water Pump?
For propylene plant condensate handling, this OH2 pump delivers reliable, low-maintenance performance with API 610 heavy duty construction. Its corrosion-resistant material options, robust sealing for hydrocarbon service, and low NPSHr make it the ideal choice for safe and efficient transfer of propylene‑contaminated condensate in PDH units, steam crackers, and polypropylene plants.
Need more information or a quotation?
Please contact us at: info@hyrig.com
Our engineering team is ready to provide technical data, selection support, and after‑sales service. Please specify your required flow, head, operating temperature, and condensate composition (propylene, propane content) for a precise recommendation.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.