Regenerator Bottom Pump – API 610 OH2 / BB3 / VS4 for Lean Amine & Column Bottoms Transfer

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
API 610 regenerator bottom pump for removing lean amine or stripped liquid from regenerator/stripper bottom. OH2 single-stage, BB3 multistage for high head, VS4 vertical sump. 316L stainless steel (S-8) wetted parts. API 682 Plan 53B dual pressurized seals. Flows 10–1500 m³/h, heads 20–1500 m. 20-year design life, 3-year continuous run.

Conatct For Details
DetailReview(0)Additional

Product Overview

The Regenerator Bottom Pump is designed to remove the stripped liquid from the bottom of a regenerator (stripper) column in gas sweetening, refinery hydrodesulfurization (HDS), carbon capture (CCUS), and other amine or solvent regeneration processes. The most common fluid handled is lean amine – the regenerated amine solution that has been stripped of H₂S and CO₂ – which is then sent to a reboiler for steam generation or directly to the lean amine charge pump for circulation back to the absorber. The pump may also handle other regenerator bottoms such as stripped sour water, glycol, or solvent.

Because the fluid is typically hot (100–130°C), may contain residual H₂S, and is corrosive, the pump must meet the highest standards of reliability, thermal stability, and leakage containment. All pumps are fully compliant with API 610 11th/12th edition (ISO 13709) – ensuring a 20‑year design life and minimum 3‑year uninterrupted operation.

Pump Configurations for Regenerator Bottom Service

Pump TypeConfigurationBest Regenerator Bottom Application
OH2 (Preferred)Overhung, centreline‑mounted, single‑stageLean amine transfer to reboiler or lean charge pump (heads ≤150 m, flows 10–600 m³/h)
BB3Axially split, multistage, between bearingsHigh‑head transfer (heads >150 m) to distant equipment or high‑pressure systems
VS4Vertical suspended sump / can typeSump evacuation, low NPSHa, or space‑constrained installations

Key Technical Specifications

ParameterOH2BB3VS4
Flow range10 – 600 m³/h50 – 1500 m³/h10 – 750 m³/h
Head range20 – 260 m (typical 50–150 m)100 – 1500 m15 – 280 m
Pressure ratingUp to 64 barUp to 150 barUp to 40 bar
Temperature–45 to +200°C–45 to +200°C–46 to +260°C
Speed1,450 / 2,950 rpm1,450 / 2,950 rpm1,450 / 2,950 rpm

Materials – API 610 Table H

Lean amine at regenerator bottom is typically 110–130°C and may contain residual H₂S and heat‑stable salts. 316L stainless steel (API 610 Class S‑8) is the minimum standard. Carbon steel corrodes rapidly at these temperatures.

ComponentMaterial (Standard)Upgrade Option
Casing316L SS (CF3M)Duplex (D‑1/D‑2), Super Duplex (U‑8)
Impeller316L SSDuplex, Super Duplex, 17‑4 PH
Shaft316 SS or 4140 with coating17‑4 PH, Duplex SS
Wear rings316L SS + Stellite hard‑facingTungsten carbide
Gaskets / O‑ringsSpiral wound (graphite) / FKMAflas for higher temperature

For lean amine with H₂S residual above NACE limits, NACE MR0175 / ISO 15156 certification is required.

Mechanical Seals – API 682 Compliance

Although lean amine has less H₂S than rich amine, residual H₂S and high temperature still require robust sealing. Dual pressurized seals (API 682 Arrangement 3) with Plan 53B are recommended. For clean, low‑H₂S lean amine, a tandem seal with Plan 52 may be acceptable.

Seal ArrangementAPI 682 PlanApplication
Dual pressurised (Arr. 3)Plan 53BRecommended – zero emissions, handles hot lean amine safely
Tandem seal (Arr. 2)Plan 52Acceptable for very low H₂S, well‑ventilated areas
Single seal (Arr. 1)Plan 11 / 23Not recommended for hot amine; Plan 23 (cooled) may be used for water‑like fluids

Plan 53B provides barrier fluid pressurised above process pressure. Seal faces: silicon carbide (SiC) / SiC. Elastomers: FKM for up to 120°C; Aflas for higher temperatures.

NPSH Considerations

The regenerator bottom pump typically takes suction from the bottom of a column operating near atmospheric pressure (or slight vacuum in some designs). NPSHa is often limited to 3–6 meters from the liquid level above the pump centreline. The fluid is hot, near its boiling point. Dissolved gases (CO₂, H₂S, methane) can flash easily.

  • Ensure suction piping is short, direct, and insulated.

  • Calculate NPSHa at the bubble point – do not assume subcooling.

  • Select a low‑NPSHr impeller or add an inducer if margin is insufficient.

  • Maintain NPSHa ≥ NPSHr + 1.0 m per API 610.

Minimum Flow Protection

During normal operation, the regenerator bottom pump continuously circulates lean amine to the reboiler or to the lean charge pump. If the downstream valve closes, an automatic recirculation valve (ARC) or a continuous bypass with orifice must return minimum flow to the regenerator bottom.

Applications for Regenerator Bottom Pump

IndustryProcessFluidRecommended Configuration
Natural gas sweeteningAmine regenerationLean MDEA / MEA (110–130°C)OH2 (standard)
Refinery HDSAmine strippingLean MDEA / DEAOH2 or BB3
CCUS (carbon capture)MEA regenerationLean MEAOH2
Sour water strippingSour water regeneratorStripped sour waterOH2 (316L SS or duplex)
Glycol dehydrationGlycol regeneratorLean glycolOH2 (carbon steel or 316L)

API 610 Compliance Highlights

  • Design life: 20 years minimum

  • Continuous operation: Minimum 3 years uninterrupted service

  • Bearing life: L10 ≥25,000 hours

  • Critical speed: ≥120% of maximum operating speed

  • Centreline mounting (OH2/BB3): Essential for hot service (100–130°C)

  • Hydrostatic test: 1.5x design pressure

  • Performance test: Water per API 610 Grade 1 or 2

  • Material certification: EN 10204 3.1 full traceability

  • NACE MR0175 / ISO 15156 available for sour lean amine

Why Choose Our Regenerator Bottom Pump?

  • Full API 610 compliance (OH2 / BB3 / VS4) – 11th/12th edition ISO 13709, 20‑year life

  • 316L stainless steel (S‑8) as standard – proven corrosion resistance in hot lean amine

  • API 682 Plan 53B dual pressurised seals – zero emissions, safe hot amine handling

  • Broad hydraulic coverage – flows 10–1500 m³/h, heads 20–1500 m

  • Low NPSH designs – inducer option for low‑elevation regenerator columns

  • Centreline mounting – maintains alignment during thermal cycling (up to 200°C)

  • Easy maintenance – back pull‑out (OH2), axial split (BB3), vertical withdrawable (VS4)

  • Minimum flow protection – ARC or bypass integrated

  • NACE MR0175 / ISO 15156 compliant options

  • Field proven – thousands of regenerator bottom pumps in gas plants and refineries worldwide

Recommended Spare Parts (Per Pump)

ComponentRecommended Quantity
Mechanical seal cartridge (Plan 53B ready)1 set
Bearing set (radial + thrust)1 set
Wear ring set (casing + impeller)1 set
Gasket / O‑ring kit (full set)1 set
Inducer (if fitted)1 set

Get a Quote or Engineering Support

For selection of the correct Regenerator Bottom Pump for your amine or solvent regeneration unit – including column bottom conditions (temperature, pressure, fluid composition), NPSHa calculation, material selection (316L SS, duplex, or NACE MR0175), API 682 seal plan (Plan 53B), and complete API 610 data sheet – please contact our engineering team.

Email: info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit