A sea water pump handles untreated or filtered seawater for cooling, fire protection, desalination, or process service. Seawater is highly corrosive (chlorides ≈ 19,000–26,000 ppm), with potential for biofouling, erosion (from sand or marine growth), and low ambient temperatures. Material selection – duplex stainless steel, super duplex, or bronze/aluminum bronze – is critical for long service life. Our API 610 VS4 and OH2 pumps are specifically engineered for reliable seawater duty. Both designs fully comply with API 610 11th/12th edition (ISO 13709) .
API 610 VS4 – Vertical Long Shaft Sea Water Pump
Structure match check: API 610 VS4 is defined as a vertical, single‑casing, rigid shaft, suspended pump with discharge head above the pit cover. This is the preferred configuration for seawater intake from a sump, pit, or caisson.
Why VS4 for seawater?
Installed above a seawater intake sump – pump submerged, motor at grade.
Small footprint – ideal for crowded coastal or offshore platforms.
Flooded suction – impeller always submerged, no priming needed.
Long shaft / column pipe – can reach water levels several meters below grade.
Easy withdrawal – entire pump can be pulled vertically for maintenance without dewatering the sump.
Material flexibility – all wetted parts in duplex or super duplex.
Flow range – 100 to 15,000 m³/h.
Head range – up to 100 m (typical seawater lift).
Typical VS4 seawater applications
Seawater cooling intake pumps (power plants, refineries).
Desalination plant feed pumps (reverse osmosis pretreatment).
Coastal LNG terminal firewater pumps (from sea chest).
Offshore platform service water pumps.
API 610 OH2 – Horizontal Overhung Sea Water Pump
Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This is suitable for seawater applications where the pump is above ground, fed from a pressurized main or a tank/filtered source (no suction lift).
Why OH2 for seawater?
Compact, economical for moderate flow (5 to 1500 m³/h).
Back pull‑out maintenance – seal, bearing, impeller access without disturbing piping.
Good for pump rooms or concrete baseplate installations.
Material options – duplex, super duplex, bronze fitted.
Head range – up to 150 m.
Typical OH2 seawater applications
Seawater cooling for small plants or equipment (e.g., exchangers, compressors).
Boiler feed water pre‑treatment (low pressure seawater supply).
Firewater jockey pumps (if suction is from pressurized ring).
Reverse osmosis low‑pressure feed (after cartridge filters).
Comparison & Selection Guide
| Feature | VS4 (Vertical Long Shaft) | OH2 (Horizontal Overhung) |
|---|---|---|
| API 610 type | VS4 – vertical, suspended, rigid shaft | OH2 – horizontal overhung, foot‑mounted |
| Installation | Above sump / pit / caisson | Above ground, baseplate mounted |
| Suction | Flooded (submerged impeller) | Requires positive pressure (flooded suction or short lift) |
| Footprint | Small (motor at grade, pump below) | Larger (horizontal length) |
| Materials | Duplex / super duplex / bronze | Duplex / super duplex / bronze |
| Flow range | 100 – 15,000 m³/h | 5 – 1500 m³/h |
| Head range | Up to 100 m | Up to 150 m |
| Best for | Large flow, suction from sea or sump | Moderate flow, above‑ground installation |
Key design features for seawater service (both types)
Corrosion resistant materials – Minimum recommended: duplex stainless steel (UNS S31803 / S32205) for wetted parts. For highly aggressive seawater (higher chlorides, elevated temperature), super duplex (S32750) or 6% moly austenitic (UNS S31254). Bronze (ASTM B148 C95800) also acceptable for impeller/casing in some applications.
Coatings – Internally coated with high‑build epoxy on carbon steel parts (e.g., motor stool, column pipe). All fasteners: 316SS or duplex.
Biofouling prevention – Column pipe and casing can be designed with copper‑nickel cladding or chlorination injection points.
Wear rings – Hardered super duplex or Stellite for erosion resistance if sand/sediment present.
Shaft protection – Shaft sleeve in 316SS or duplex with O‑ring seals to prevent corrosion under sleeve.
Sealing – Plan 11 (recirculation) for clean seawater. Plan 31 (cyclone separator) if sand present. For intermittent service (firewater), gland packing acceptable. Mechanical seal faces: SiC vs. SiC for corrosion resistance.
Bearing arrangement – For VS4, product lubricated rubber bearings (water‑lubricated) along the column. Oil lubricated bearings in motor support stand. For OH2, anti‑friction bearings oil bath.
Cathodic protection – Optional sacrificial anodes (zinc or aluminum) in casing or column pipe.
Why choose our API 610 seawater pumps?
Full API 610 compliance – VS4/OH2 types verified. Performance test, mechanical run test.
Correct metallurgy – Our engineers select optimal duplex / super duplex / bronze grade for your seawater chemistry (temperature, salinity, sand content, biological activity).
Long service life – High resistance to pitting, crevice corrosion, and erosion.
Short lead time – Standard sizes (duplex) available from stock or 12-16 weeks.
Global spare parts support – Column pipes, impellers, shaft sleeves, rubber bearings, mechanical seals shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours minimum) with vibration and bearing temperature monitoring.
Hydrostatic test of casings and column pipe.
Material traceability EN 10204 3.1 / 3.2.
PMI (positive material identification) for all alloy components.
NDE – MT, PT, UT as required.
How to specify your seawater pump
Please provide: flow (m³/h), head (m), temperature (°C), salinity (g/L), sand/sediment content, biofouling potential, installation type (above sump/pit or above ground), water depth (for VS4 column length), NPSHa (m), and required material (duplex / super duplex / bronze). We will recommend VS4 or OH2 type, material grade, column length (VS4), seal plan, and driver details.
Contact us
For a quotation or technical discussion on sea water pumps (API 610 VS4 or OH2) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.