A brine pump handles concentrated salt solutions – typically sodium chloride (NaCl) or calcium chloride (CaCl₂) – used in refrigeration systems (secondary coolants), deicing, chemical manufacturing, food processing, and salt production. Brine is corrosive to carbon steel, may contain solids (salt crystals), and often operates at low temperatures (down to -40°C for CaCl₂). Our API 610 OH2 and VS4 pumps are specifically engineered for reliable brine service. Both designs fully comply with API 610 11th/12th edition (ISO 13709) .
API 610 OH2 – Horizontal Brine Pump
Structure match check: API 610 OH2 is defined as a horizontal, single‑stage, overhung pump with foot‑mounted casing and back pull‑out design. This is suitable for above‑ground brine transfer and circulation where suction conditions are positive (e.g., from a tank with adequate NPSH).
Why OH2 for brine?
Compact, economical for flow 5 to 1500 m³/h, head up to 200 m.
Back pull‑out maintenance – impeller, seal, bearings accessible without disturbing piping.
Corrosion resistant materials – 316SS, duplex, or bronze wetted parts.
Low temperature capability – down to -40°C with proper materials and seal support.
Mechanical seal – Plan 11 (recirculation) or Plan 32 (external flush to prevent salt crystallization). Tandem/double seals for zero emissions.
Typical applications: brine circulation in chillers, deicing fluid transfer, salt plant pumps.
API 610 VS4 – Vertical Brine Pump
Structure match check: API 610 VS4 is defined as a vertical, single‑casing, rigid shaft, suspended pump with discharge head above the pit cover. This is ideal when suction is from a pit, sump, or tank with low liquid level, or when space is limited.
Why VS4 for brine?
Flooded suction – impeller submerged, no priming issues, ideal for low NPSH.
Small footprint – pump sits above a sump or tank.
Easy withdrawal – entire assembly pulls vertically for maintenance without emptying the sump.
Corrosion resistant column and casing – duplex, 316SS, or bronze.
Flow range – 10 to 5000 m³/h, head up to 100 m.
Typical applications: brine make‑up from salt dissolvers, evaporator pits, brine return sumps.
Key design features for brine service (both types)
Material selection –
316SS (CF8M/CF3M) for NaCl brine up to moderate concentrations and temperature.
Duplex (2205) for higher chlorides or aggressive CaCl₂.
Bronze (aluminum bronze or silicon bronze) for lower cost in moderate duty.
For very low temperature (below -30°C), low‑temperature carbon steel with stainless trim may be acceptable if de‑rated.
Gaskets: PTFE or EPDM (compatible with salt solutions).
Low temperature handling – For brine down to -40°C:
Mechanically sealed pumps require Plan 23 (cooled recirculation) or Plan 62 (quench) to prevent ice formation.
Gland packing may freeze – mechanical seal preferable.
Bearing housing may require cooling fan or oil mist.
Stainless steel or bronze impellers (no cast iron at low temp).
Crystallization prevention – Brine can deposit salt crystals on seal faces if temperature drops or concentration increases. Use Plan 32 (external fresh water flush) or heated seal chambers. For VS4 with rubber bearings, ensure continuous flow to prevent salt buildup.
Sealing – Plan 11 (recirculation) for clean brine. Plan 31 (cyclone separator) if crystals present. Plan 32 (external water flush) to keep seal faces clean. Double seals with Plan 53A for zero emissions.
Impeller – Closed for clean brine; semi‑open or open for brine with salt crystals (up to 5-8mm). Hardened 17-4PH or Stellite wear rings.
Bearings – For VS4, product lubricated rubber bearings (compatible with brine). For OH2, anti‑friction bearings with oil bath or oil mist.
Typical performance range
| Parameter | OH2 | VS4 |
|---|---|---|
| Flow rate | 5 – 1500 m³/h | 10 – 5000 m³/h |
| Head | Up to 200 m | Up to 100 m |
| Temperature | -40°C to +80°C | -40°C to +80°C |
| Pressure rating | Up to 25 bar | Up to 10 bar (low pressure typical) |
| Speeds | 1450 / 2900 / 3600 rpm | 750 / 1450 / 2900 rpm |
Typical applications
Refrigeration secondary coolant circulation (CaCl₂ or NaCl brine in chillers, ice rinks, food cold storage).
Deicing fluid transfer (airports, road deicing).
Salt production – brine pumping from dissolvers, clarifiers, evaporators.
Chemical process – brine for chlorine/caustic production or as a raw material.
Oil & gas – drilling mud mixing (brine as base fluid).
Food processing – brine for pickling or cheese production (sanitary designs available).
Why choose our API 610 brine pumps?
Full API 610 compliance – OH2 and VS4 types verified per standard.
Corrosion resistant materials – Correct alloy selection for your brine type, concentration, and temperature.
Low temperature engineered – Avoid freezing seals, brittle fracture, and bearing failure.
Crystallization prevention – Seal flush plans (Plan 32/Plan 62) keep pump running in saturated brine.
Easy maintenance – Back pull‑out (OH2) or vertical withdrawal (VS4).
Short lead time – Standard 316SS versions available from stock; duplex/bronze 8-12 weeks.
Global spare parts support – Impellers, shafts, bearings, seals, column pipe sections shipped worldwide.
Quality assurance
ISO 9001:2015 certified.
API 610 mechanical run test (4 hours minimum) with vibration and bearing temperature monitoring.
Hydrostatic test of casing and column pipe.
Material traceability EN 10204 3.1 / 3.2.
PMI for alloy components.
Low temperature impact testing (optional for -40°C or below).
How to specify your brine pump
Please provide: flow (m³/h), head (m), brine type (NaCl or CaCl₂), concentration (% by weight), temperature (°C), NPSHa (m), presence of salt crystals (yes/no, size), installation type (horizontal above ground or vertical in sump/pit), and required material (316SS / duplex / bronze). We will recommend OH2 or VS4 type, impeller design (closed/semi‑open), seal plan (11/32/53A), low temperature provisions, and driver details.
Contact us
For a quotation or technical discussion on brine pumps (API 610 OH2 or VS4) :
info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.