he Sulzer MSD is an API 610 (ISO 13709) Type BB3 horizontal, axially split, between‑bearings, multistage centrifugal pump. It is a heavy‑duty process pump designed for the most demanding high pressure, high temperature applications where maximum reliability, efficiency, and maintainability are non‑negotiable.
The MSD features a horizontally split casing (axial split) allowing full access to the internal rotating assembly by lifting the top casing half – all without disturbing suction or discharge piping. This design makes the MSD a prime choice for carbamate service in urea plants, where maintenance windows are short and access must be fast.
Why MSD for High Pressure Carbamate?
Urea synthesis involves the formation of highly corrosive ammonium carbamate (NH₂COONH₄) at elevated pressures and temperatures. The MSD pump is engineered to recirculate carbamate from the carbamate condenser or recovery section back to the high pressure urea reactor, operating continuously under extreme conditions.
Over 10,000 MSD pumps installed globally in pipelines, boiler feed, water injection, and nuclear safety‑related services – a proven design with decades of field experience.
Broadest hydraulic coverage of any BB3 type multistage pump in the market.
Opposed impeller design provides inherent axial thrust balance, eliminating the need for complex balance drums or disks.
Axially split casing enables complete internal inspection and part replacement without removing the pump from the baseplate or disconnecting the carbamate piping.
Key Parameters
Capacities: Up to 3,200 m³/h
Total head: Up to 2,900 m / 9,500 ft
Operating pressure: Up to 300 bar / 4,400 psi
Operating temperature: Up to +205°C
Discharge sizes: 150 to 350 mm / 6 to 14 inches
Maximum speed: Up to 6,000 rpm
Flange ratings: 600#, 900#, 1500# to suit project requirements
API Classification
The MSD is typically classified as an API 610 Type BB3 (axially split, multistage, between bearings). This classification provides:
Single casing with horizontal split line
Maintenance without disturbing piping
Opposed impeller configuration for axial thrust balance
Suitable for medium to very high pressure services, including carbamate recirculation, high pressure ammonia feed, and urea reactor feed.
For extremely high pressure carbamate duties exceeding the BB3 pressure rating (e.g., >400 bar), Sulzer offers the Type BB5 barrel pump (e.g., GSG, CP, HPcp series) as the appropriate solution. The MSD remains the optimal BB3 choice for the majority of carbamate recirculation and urea synthesis feed applications with pressures up to 300 bar.
Design Features
| Feature | Benefit |
|---|---|
| Axially split casing | Top half lifts off for full rotor access without disconnecting suction/discharge piping – minimises maintenance downtime in corrosive carbamate service. |
| Opposed impeller arrangement | Impellers arranged back‑to‑back generates inherent axial thrust self‑balancing, eliminating complex thrust balancing mechanisms (balance drum/disc) and reducing lube oil system costs. |
| Double suction first‑stage impeller (available on most sizes) | Significantly reduces Net Positive Suction Head Required (NPSHr) – critical for carbamate loops with limited available suction head. |
| Between‑bearings construction | Rigid shaft supported by bearings at both ends ensures exceptional stability, minimal deflection, and smooth operation at high pressures. |
| Industry‑leading hydraulic coverage | Broad performance map allows precise selection for specific carbamate recirculation duties without oversizing. |
| API 682 seal chamber | Fully compliant with API 682 4th Edition, accommodating single, tandem (Plan 52/53A), and double (Plan 53B) cartridge mechanical seals. |
| Renewable wear parts | Casing rings, impeller rings, and interstage bushings are field‑replaceable, restoring pump efficiency without replacing major castings. |
| Standard and high pressure casings | Multiple flange options available to meet carbamate synthesis loop pressure requirements. |
| Heavy duty bearings | Angular contact thrust bearings and cylindrical roller radial bearings; oil ring self‑lubricating (standard) or forced oil circulation (high power). |
| Bearing housing cooling | Water‑cooled bearing housings available – recommended for carbamate service above 150°C to maintain bearing temperatures within safe limits (≤70°C). |
Materials for Urea and Carbamate Service
High pressure carbamate pumps require rigorous material selection to withstand the aggressive ammonium carbamate corrosion. Standard 316L stainless steel has proven inadequate for high temperature carbamate service. The following material matrix provides selection guidance:
| Service Condition | Required Material (Wetted Parts) |
|---|---|
| Urea solution transfer, moderate temperature | 316L stainless steel |
| Potassium carbonate solution (hot carbonate CO₂ removal) | 316L stainless steel or Duplex 2205 |
| Ammonium carbamate recirculation, elevated temperature, moderate concentration | Super duplex 25% Cr minimum (e.g., SAF 2507, UNS S32760) |
| High pressure carbamate feed with carbamate decomposition potential | Super duplex 25% Cr + hard facing on wear rings / interstage bushings |
| Aggressive carbamate service with chloride contamination | Super duplex (25% Cr) or higher alloys (Hastelloy C‑276) |
Material recommendations by component (carbamate service):
| Component | Material |
|---|---|
| Casing (inner) | Super duplex 25% Cr (SAF 2507 / UNS S32750) |
| Impellers | Super duplex 25% Cr |
| Shaft | Super duplex or Inconel 718 |
| Wear rings (casing/impeller) | Super duplex with Stellite hard facing |
| Interstage bushings | Silicon carbide (SiC) or tungsten carbide (TC) |
| Casing bolting | A193 B8M Class 2 (316 SS) or super duplex |
| Gaskets / O‑rings | PTFE or FFKM (Kalrez / Chemraz) – EPDM and Buna‑N are NOT recommended. |
API 610 Material Classes Available:
S‑4, S‑5, S‑6, S‑8 – austenitic stainless steels (304, 316, high silicon)
C‑6 – duplex stainless steel
A‑8 – Alloy 20 (CN7M)
D‑1 / D‑2 – higher alloys (Hastelloy, Inconel)
NACE MR0175 / MR0103 compliance for sour service when required.
Flush Plan & Seal Selection
For ammonium carbamate service (toxic, corrosive, high pressure), API 682 sealing is mandatory to prevent leakage to atmosphere.
| Service | Recommended Seal Configuration | Flush Plan |
|---|---|---|
| Ammonium carbamate (toxic, corrosive) | Double mechanical seal (pressurized) | Plan 53B – Pressurized barrier fluid reservoir with bladder accumulator |
| Carbamate recirculation (moderate hazard) | Tandem mechanical seal | Plan 52 – Unpressurized buffer fluid reservoir with leak monitoring |
| Low risk water‑based carbamate solutions | Single mechanical seal (not recommended) | Plan 11 (internal recirculation) |
Seal face recommendations: Tungsten carbide vs. carbon (inner seal, for low lubricity carbamate). Silicon carbide vs. carbon (outer seal).
Secondary seals: FFKM (Kalrez / Chemraz) for chemical compatibility with carbamate and barrier fluid.
Plan 53B system requirements: Reservoir with bladder accumulator, pressure transmitter (1‑3 bar above pump suction pressure), level transmitter (low level alarm for potential inner seal leakage), temperature transmitter, nitrogen supply connection.
Auxiliary Systems
| System | Requirement for Carbamate Service |
|---|---|
| Minimum flow protection | Automatic recirculation valve (ARC) or control valve + orifice required to ensure pump stays above minimum continuous stable flow – prevents overheating and cavitation. |
| Bearing cooling water | Water‑cooled bearing housings required for carbamate service >150°C – maintains bearing temperature ≤70°C. |
| Casing drain connections | Low point drains with double isolation valves for carbamate purging and maintenance – essential for safe disassembly. |
| Flushing connections | Connections on casing and seal chamber for solvent flushing during maintenance. |
| Barrier fluid system (Plan 53B) | Complete skid‑mounted reservoir, bladder accumulator, pressure/level/temperature instrumentation, nitrogen panel, and controls. |
| Baseplate | Heavy duty fabricated steel baseplate, epoxy grouted, designed to 2× API 610 nozzle load requirements. |
Monitoring Systems (APl 670 Requirements)
| Monitoring System | Specification |
|---|---|
| Bearing temperature | RTD probes (PT100) in both drive‑end and non‑drive‑end housings, 4‑20 mA to DCS, alarm at 85°C, trip at 95°C. |
| Vibration monitoring | Proximity probes (eddy current) for shaft radial vibration; accelerometers for bearing housing velocity (optional). |
| Suction pressure | Chemical seal diaphragm gauge with 4‑20 mA transmitter to DCS – low suction pressure interlock to protect against NPSH violation. |
| Discharge pressure | Pressure transmitter with high limit alarm to DCS. |
| Process temperature | Thermowell‑mounted temperature transmitter on suction and discharge nozzles. |
Sulzer MSD Applications
Fertilizer industry: Carbamate recirculation in high pressure urea synthesis; lean/rich solution pumps; urea solution transfer.
Refined product pipelines: Crude oil, LPG, and hydrocarbon transfer over long distances.
Boiler feed water: Conventional and nuclear power plants.
Water injection: High pressure water injection for oil reservoir pressure maintenance.
Nuclear safety‑related services: High reliability, high pressure applications.
Desalination: MSD‑RO variant for reverse osmosis membrane high pressure feed.
C02 injection: Enhanced oil recovery (EOR) and carbon capture storage.
Sulzer MSD in China
Sulzer has a significant local presence in China, with service centers that can maintain and revitalize existing MSD pumps, and also supply equipment for new projects.
Local manufacturing and service facilities:
Dalian: Manufacturing facility serving hydrocarbon processing, oil & gas, and power generation clients.
Suzhou: Pump production for similar heavy‑duty process industries.
Kunshan: Sixth production plant in China (opened 2012), expanding Sulzer's local supply capability.
These facilities provide local manufacturing, spare parts supply, and service support for MSD pumps across all major industries, including fertilizers.
Why Choose Sulzer MSD for High Pressure Carbamate?
Proven BB3 axially split design – over 10,000 units installed worldwide in demanding services including nuclear, ensuring exceptional reliability.
Full API 610 compliance – designed and manufactured to the most stringent international standard for heavy duty process pumps.
Opposed impeller thrust balancing – eliminates complex balance drums or disks, reducing lube oil system costs and improving reliability.
Axially split casing – full rotor access without removing piping, critical for carbamate service where maintenance must be fast and safe.
Industry‑leading hydraulic coverage – the broadest range of any BB3 pump allows precise matching to urea plant carbamate duty.
Double suction first stage – significantly improves low NPSH performance for challenging suction conditions.
Material flexibility – 316L, super duplex (25% Cr), duplex, high alloys, and NACE compliance available.
API 682 seal compatibility – Plan 53B (pressurized barrier fluid) ensures zero leakage of toxic, corrosive carbamate to environment.
Local support in China – manufacturing and service facilities in Dalian, Suzhou, and Kunshan providing local supply and after‑sales support for MSD pumps.
For more information or a custom proposal for your high pressure carbamate pump (Sulzer MSD) application, contact us at info@hyrig.com
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.