Sulzer MSD Lean Solution Pump – API 610 BB3 Axially Split Multistage Pump

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Sulzer MSD axially split multistage centrifugal pump for lean solution (hot potassium carbonate) circulation in CO2 absorption/desorption loops. Flow to 3,200 m³/h, head to 2,900 m, pressure to 300 bar, temperature to +205°C. API 610 BB3 design with opposed impellers, axially split casing, double suction first stage available. Materials: 316L, duplex, super duplex for corrosion resistance. Suitable for Benfield, Vetrocoke, and other hot carbonate CO2 removal units.

Conatct For Details
DetailReview(0)Additional

The Sulzer MSD is an API 610 (ISO 13709) Type BB3 horizontal, axially split, between‑bearings, multistage centrifugal pump. It is engineered for demanding high pressure, high temperature services requiring maximum reliability and maintainability. For lean solution circulation in hot potassium carbonate CO2 removal systems, the MSD provides the optimal combination of hydraulic performance, corrosion resistance, and maintainability.

Lean Solution Service Overview

In the hot potassium carbonate process (Benfield, Vetrocoke, or other activated carbonate systems), lean solution – regenerated potassium carbonate (K₂CO₃) stripped of CO₂ – is pumped from the desorber/stripper bottom back to the absorber top to continue the closed‑loop absorption cycle. The lean solution pump is a critical service pump, operating typically at 110–130°C and pressures up to 70–100 bar (depending on plant design). The pump must handle slightly corrosive alkaline solution, provide years of continuous service, and allow quick maintenance within the limited windows of fertilizer plant turnarounds.

Key Parameters

  • Capacities: Up to 3,200 m³/h (hydraulic range covers most lean solution duties)

  • Total head: Up to 2,900 m / 9,500 ft

  • Operating pressure: Up to 300 bar / 4,400 psi (far exceeding typical lean solution requirements)

  • Operating temperature: Up to +205°C (covers typical 120°C lean solution)

  • Discharge sizes: 150 to 350 mm / 6 to 14 inches

  • Max speed: Up to 6,000 rpm

  • Flange ratings: 600#, 900#, 1500# to suit project requirements

Design Features for Lean Solution

FeatureBenefit
Axially split casingHorizontally split along centerline; top half lifts off for full rotor access without disconnecting suction/discharge piping – minimises maintenance downtime in continuous operation.
Opposed impeller arrangementImpellers arranged back‑to‑back provides inherent axial thrust self‑balancing, eliminating complex balance drums/disks and reducing lube oil system complexity.
Double suction first‑stage impeller (available on most sizes)Reduces Net Positive Suction Head Required (NPSHr) – essential for lean solution loops with limited available suction head, preventing cavitation in hot carbonate solution.
Between‑bearings constructionRigid shaft supported by bearings at both ends ensures exceptional stability, minimal deflection, and smooth operation at elevated temperatures and pressures.
Renewable wear partsCasing rings, impeller rings, and interstage bushings are field‑replaceable, restoring pump efficiency without replacing major castings – reduces long‑term maintenance cost.
API 682 seal chamberFully compliant with API 682 4th Edition, accommodating single, tandem (Plan 52/53A), and double (Plan 53B) cartridge mechanical seals for zero leakage of corrosive carbonate solution.
Heavy duty bearingsAngular contact thrust bearings and cylindrical roller radial bearings; oil ring self‑lubricating (standard) or forced oil circulation (high power). Water‑cooled bearing housings available – recommended for lean solution service above 120°C.
Bearing housing coolingWater‑cooled housings maintain bearing temperature ≤70°C when pumping hot carbonate at 120°C, extending bearing life.

Materials for Lean Solution (Hot Potassium Carbonate)

Selecting the correct material is critical for long‑term corrosion resistance in hot potassium carbonate service. The following table provides material recommendations:

Service ConditionRecommended Material (Wetted Parts)
Lean potassium carbonate solution (K₂CO₃), up to 120°C, clean316L stainless steel
Lean potassium carbonate with trace chlorides or low pHDuplex 2205 or super duplex 2507
Lean solution with higher corrosion potential (elevated temperature, impurities)Super duplex 25% Cr minimum (e.g., SAF 2507, UNS S32760)
Carbonate solution containing activators (amines, promoters)316L or duplex (depending on activator chemistry)

Material recommendations by component (lean solution service):

ComponentStandard (Clean Carbonate)Upgrade (Corrosive / High Temperature)
Casing (inner)316L stainless steelDuplex 2205 / Super duplex 25% Cr
Impellers316L stainless steelDuplex 2205 / Super duplex
Shaft17-4PH or 316L stainless steelDuplex / Super duplex
Wear rings (casing/impeller)316L with Stellite hard facingDuplex with Stellite / Silicon carbide
Interstage bushingsSilicon carbide or bronzeTungsten carbide
Casing boltingA193 B8M Class 2 (316 SS)Duplex / Super duplex
Gaskets / O‑ringsPTFE or EPDMFFKM (Kalrez) for aggressive conditions

Note: Carbon steel is NOT acceptable for hot potassium carbonate service above 80°C due to accelerated corrosion. 316L is the minimum for lean solution service; duplex or super duplex provides additional corrosion resistance and strength margin.

Flush Plan & Seal Selection

For lean solution (moderately corrosive, non‑toxic compared to carbamate), the following seal arrangements are typically used:

ServiceRecommended Seal ConfigurationFlush Plan
Lean carbonate solution, clean, moderate temperatureSingle mechanical seal (API 682 Type A)Plan 11 (internal recirculation with orifice)
Lean carbonate solution, higher temperature (>100°C)Single seal with coolerPlan 21 or Plan 23 (cooled recirculation)
Zero‑leak, fugitive emission controlTandem mechanical sealPlan 52 (unpressurized buffer fluid reservoir)
Highly corrosive or hazardous (e.g., with H₂S)Double mechanical seal (pressurized)Plan 53B

Seal faces: Silicon carbide vs. carbon (standard). For dirty or scaling service, tungsten carbide vs. carbon.

Secondary seals: EPDM or PTFE (compatible with hot carbonate). If aggressive chemicals present, upgrade to FFKM.

Auxiliary Systems

SystemRequirement for Lean Solution Service
Minimum flow protectionAutomatic recirculation valve (ARC) or control valve + orifice – ensures pump never operates below minimum continuous stable flow, preventing overheating and cavitation in hot carbonate loops.
Bearing cooling waterWater‑cooled bearing housings recommended for lean solution >100°C – extends bearing life.
Casing drainsLow point drains with isolation valves for safe cleaning and maintenance.
Flushing connectionsConnections on casing and seal chamber for washing before maintenance – important for carbonate solution that may dry and deposit crystals.
BaseplateHeavy duty fabricated steel baseplate, epoxy grouted, designed to 2× API 610 nozzle load requirements.

Monitoring Systems (API 670 Requirements)

Monitoring SystemSpecification
Bearing temperatureRTD probes (PT100) in drive‑end and non‑drive‑end housings, 4‑20 mA to DCS, alarm at 85°C, trip at 95°C.
Vibration monitoringProximity probes (eddy current) for shaft radial vibration (recommended); accelerometers for bearing housing velocity (optional).
Suction pressurePressure gauge with 4‑20 mA transmitter – low suction pressure alarm to protect against NPSH violation.
Discharge pressurePressure transmitter with high limit alarm to DCS.
Process temperatureThermowell‑mounted temperature transmitter on suction and discharge nozzles – critical for ensuring lean solution is above crystallization point.

Applications

The Sulzer MSD lean solution pump is suitable for:

  • Benfield CO₂ removal units: Lean carbonate solution circulation from regenerator to absorber.

  • Vetrocoke process: Similar hot carbonate lean solution service.

  • Other activated hot carbonate systems: Including those using amines or other promoters.

  • Amine lean solution circulation (MEA, DEA, MDEA): For gas sweetening applications (with appropriate materials, typically 316L).

Why Sulzer MSD for Lean Solution?

  • Proven BB3 axially split design – over 10,000 units installed globally, providing exceptional long‑term reliability.

  • Full API 610 compliance – designed and manufactured to the most stringent international standard for heavy duty process pumps.

  • Opposed impeller thrust balancing – eliminates complex balance drums/disks, reducing lube system cost and improving reliability.

  • Axially split casing – full rotor access without removing piping, critical for lean solution pumps where rapid maintenance during plant turnarounds is essential.

  • Double suction first stage – improves low NPSH performance when suction conditions are limited.

  • Material flexibility – 316L, duplex, super duplex, high alloys, NACE compliance available to match lean solution corrosivity.

  • API 682 seal compatibility – Plan 21/23 for hot carbonate; Plan 52 for zero emissions.

  • Local support in China – Sulzer manufacturing and service facilities in Dalian, Suzhou, and Kunshan provide local supply, spare parts, and after‑sales support for MSD pumps.

For more information or a custom proposal for your lean solution pump (Sulzer MSD) application, contact us at info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit