Sulzer MSD Rich Solution Pump – API 610 BB3 Axially Split Multistage Pump

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
Sulzer MSD axially split multistage centrifugal pump for rich solution (CO₂-loaded hot potassium carbonate) circulation in CO2 absorption/desorption loops. Flow to 3,200 m³/h, head to 2,900 m, pressure to 300 bar, temperature to +205°C. API 610 BB3 design with opposed impellers, axially split casing, double suction first stage available. Materials: 316L, duplex, super duplex for corrosion resistance. Suitable for Benfield, Vetrocoke, and other hot carbonate CO2 removal units, including green ammonia rich solution service.

Conatct For Details
DetailReview(0)Additional

The Sulzer MSD is an API 610 (ISO 13709) Type BB3 horizontal, axially split, between‑bearings, multistage centrifugal pump. It is engineered for demanding high pressure, high temperature services requiring maximum reliability and maintainability. For rich solution circulation in hot potassium carbonate CO2 absorption systems, the MSD provides optimal hydraulic performance and corrosion resistance.

Rich Solution Service Overview

In the hot potassium carbonate process (Benfield, Vetrocoke, or other activated carbonate systems), rich solution – potassium carbonate (K₂CO₃) that has absorbed CO₂ in the absorber tower, forming potassium bicarbonate (KHCO₃) – is pumped from the absorber bottom to the regenerator (stripper/desorber) to release CO₂ and regenerate the lean solution. The rich solution pump operates at typically 70–120°C (regenerator feed) and pressures up to 70–100 bar. The fluid is mildly corrosive, has higher CO₂ loading compared to lean solution, and may contain trace solid precipitates (bicarbonate crystals if temperature fluctuates).

Why MSD for Rich Solution?

  • Proven BB3 axially split design – over 10,000 MSD pumps installed globally in demanding services, including nuclear, ensuring exceptional reliability.

  • Full API 610 compliance – manufactured and tested to the most stringent international standard for heavy duty process pumps.

  • Opposed impeller arrangement – provides inherent axial thrust self‑balancing, eliminating complex balance drums/disks and reducing lube oil system cost.

  • Axially split casing – allows full rotor access without disconnecting piping, critical for rich solution pumps where maintenance must be fast and safe.

  • Double suction first stage – improves low NPSH performance when the absorber bottom NPSHa is limited.

  • Material flexibility – 316L, duplex, super duplex, and higher alloys available to match rich solution corrosivity (which may be slightly higher than lean solution due to CO₂‑carbonic acid formation).

Key Parameters

  • Capacities: Up to 3,200 m³/h (covers typical rich solution circulation)

  • Total head: Up to 2,900 m / 9,500 ft (far exceeding rich loop requirements)

  • Operating pressure: Up to 300 bar / 4,400 psi (covers typical 70‑100 bar)

  • Operating temperature: Up to +205°C (covers rich solution 70‑120°C)

  • Discharge sizes: 150 to 350 mm / 6 to 14 inches

  • Max speed: Up to 6,000 rpm

  • Flange ratings: 600#, 900#, 1500# to suit project requirements

Design Features for Rich Solution

FeatureBenefit
Axially split casingHorizontally split along centerline; top half lifts off for full rotor access without disconnecting suction/discharge piping – minimises maintenance downtime.
Opposed impeller arrangementBack‑to‑back impellers provide inherent axial thrust self‑balancing, eliminating balance drum/disk and reducing lube system complexity.
Double suction first‑stage impeller (available on most sizes)Reduces Net Positive Suction Head Required (NPSHr) – critical for rich solution pumps drawing from absorber bottoms with limited submergence.
Between‑bearings constructionRigid shaft supported by bearings at both ends ensures exceptional stability, minimal deflection, and smooth operation under varying loads.
Renewable wear partsCasing rings, impeller rings, and interstage bushings are field‑replaceable, restoring pump efficiency without replacing major castings.
API 682 seal chamberFully compliant with API 682 4th Edition, accommodating single, tandem (Plan 52/53A), and double (Plan 53B) cartridge mechanical seals.
Heavy duty bearingsAngular contact thrust bearings and cylindrical roller radial bearings; oil ring self‑lubricating (standard) or forced oil circulation (high power). Water‑cooled housings available – recommended for rich solution above 100°C.
Bearing housing coolingWater‑cooled housings maintain bearing temperature ≤70°C when pumping hot carbonate at 120°C, extending bearing life.

Materials for Rich Solution (CO₂-Loaded Potassium Carbonate)

While rich solution is typically slightly more corrosive than lean solution due to dissolved CO₂ (forming weak carbonic acid), and may have lower pH, material selection must account for this. The following matrix provides recommendations:

Service ConditionRecommended Material (Wetted Parts)
Clean rich potassium carbonate solution, CO₂‑loaded, up to 120°C, neutral pH316L stainless steel (minimum)
Rich solution with trace chlorides or lower pH (carbonic acid effect)Duplex 2205 or super duplex 2507
Rich solution containing activators (amines, promoters) or potential for bicarbonate crystallizationDuplex 2205
Aggressive service with H₂S or high chloride carryoverSuper duplex 25% Cr minimum (e.g., SAF 2507, UNS S32760)

Material recommendations by component (rich solution service, typical):

ComponentStandard (Clean Rich Carbonate)Upgrade (Corrosive / High Temp / Impurities)
Casing (inner)316L stainless steelDuplex 2205 / Super duplex 25% Cr
Impellers316L stainless steelDuplex 2205 / Super duplex
Shaft17-4PH stainless steelDuplex / Super duplex
Wear rings (casing/impeller)316L with Stellite hard facingDuplex with Stellite / Silicon carbide
Interstage bushingsSilicon carbide or bronzeTungsten carbide
Casing boltingA193 B8M Class 2 (316 SS)Duplex / Super duplex
Gaskets / O‑ringsPTFE or EPDMFFKM (Kalrez) for aggressive conditions

Note: Carbon steel is NOT acceptable for hot carbonate service (rich or lean) above 80°C. 316L is the minimum; duplex or super duplex provides additional corrosion resistance and strength, particularly important if the rich solution pH drops below 9.

Flush Plan & Seal Selection

For rich solution (moderately corrosive, not acutely toxic but environmentally sensitive), the following seal arrangements are typically used:

ServiceRecommended Seal ConfigurationFlush Plan
Rich carbonate solution, clean, <100°CSingle mechanical sealPlan 11 (internal recirculation with orifice)
Rich carbonate solution, >100°CSingle seal with coolerPlan 21 or Plan 23 (cooled recirculation)
Zero‑leak or fugitive emission controlTandem mechanical sealPlan 52 (unpressurized buffer fluid reservoir)
Highly corrosive or hazardous (e.g., with H₂S)Double mechanical seal (pressurized)Plan 53B

Seal faces: Silicon carbide vs. carbon (standard). For dirty or scaling service (risk of bicarbonate crystals), tungsten carbide vs. carbon.

Secondary seals: EPDM or PTFE (compatible with hot carbonate). If aggressive chemicals present, upgrade to FFKM.

Auxiliary Systems

SystemRequirement for Rich Solution Service
Minimum flow protectionAutomatic recirculation valve (ARC) or control valve + orifice – ensures pump stays above minimum continuous stable flow, preventing overheating and cavitation.
Bearing cooling waterWater‑cooled bearing housings recommended for rich solution >100°C.
Casing drainsLow point drains with isolation valves for safe cleaning and maintenance – important for removing any bicarbonate deposits before disassembly.
Flushing connectionsConnections on casing and seal chamber for washing before maintenance (warm water to dissolve any carbonate crystals).
BaseplateHeavy duty fabricated steel baseplate, epoxy grouted, designed to 2× API 610 nozzle load requirements.

Monitoring Systems (API 670 Recommendations)

Monitoring SystemSpecification
Bearing temperatureRTD probes (PT100) in drive‑end and non‑drive‑end housings, 4‑20 mA to DCS, alarm at 85°C, trip at 95°C.
Vibration monitoringProximity probes (eddy current) for shaft radial vibration (recommended for critical pumps); accelerometers for bearing housing velocity (optional).
Suction pressurePressure gauge with 4‑20 mA transmitter – low suction pressure alarm to protect against NPSH violation.
Discharge pressurePressure transmitter with high limit alarm to DCS.
Process temperatureThermowell‑mounted temperature transmitter on suction and discharge nozzles – critical for ensuring rich solution remains above crystallization point (typically >70°C) to prevent bicarbonate solids from forming.

Applications

The Sulzer MSD rich solution pump is suitable for:

  • Benfield CO₂ removal units: Rich carbonate solution circulation from absorber to regenerator.

  • Vetrocoke process: Similar hot carbonate rich solution service.

  • Other activated hot carbonate systems: Including those using amines or other promoters.

  • Green ammonia rich solution service: Circulation in CO2 capture loops for renewable hydrogen-based ammonia synthesis.

  • Amine rich solution circulation (MEA, DEA, MDEA): For gas sweetening (with appropriate materials, typically 316L or duplex).

Why Sulzer MSD for Rich Solution?

  • Proven BB3 axially split design with over 10,000 units installed globally in demanding services.

  • Full API 610 compliance – designed and manufactured to the most stringent international standard for heavy duty process pumps.

  • Opposed impeller thrust balancing – eliminates complex balance drums/disks, reducing lube system cost and improving reliability.

  • Axially split casing – full rotor access without removing piping, critical for rich solution pumps where maintenance must occur during tight plant turnarounds.

  • Double suction first stage – improves low NPSH performance when the absorber bottom provides limited submergence.

  • Material flexibility – 316L, duplex, super duplex, high alloys, NACE compliance available to match rich solution corrosivity.

  • API 682 seal compatibility – Plan 21/23 for hot carbonate; Plan 52/53B for zero emissions.

  • Local support in China – Sulzer manufacturing and service facilities in Dalian, Suzhou, and Kunshan provide local supply, spare parts, and after‑sales support for MSD pumps.

For more information or a custom proposal for your rich solution pump (Sulzer MSD) application, contact us at info@hyrig.com


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit