Shaft Sleeve (Bearing Side) 1211-200400 | Compatible with Sulzer BBS 200-400 API 610 Centrifugal Pump

2026-03-15 17:45

Shaft Sleeve (Bearing Side) 1211-200400 | Compatible with Sulzer BBS 200-400 API 610 Centrifugal Pump

Product Overview

HYRIG's Shaft Sleeve (Bearing Side) (Part No. 1211-200400) is a precision-engineered replacement component exclusively designed for Sulzer BBS 200-400 double suction centrifugal pumps, fully adhering to API 610 (12th Edition) standards. As a critical protective and positioning part for the pump shaft's bearing assembly area, this sleeve acts as a wear-resistant barrier between the shaft and angular contact bearing set (e.g., HYRIG Angular Contact Bearing SET), preventing shaft damage from lubricant contamination, bearing friction, and axial/radial loads—directly replicating Sulzer's original design dimensions, fit, and performance at a cost-effective price point.

Crafted for demanding industrial environments (chemical processing, petroleum refining, power generation, and water treatment), the bearing-side shaft sleeve features a high-precision cylindrical surface and shoulder design that ensures optimal bearing seating, alignment, and load distribution. Each unit undergoes strict dimensional inspection, concentricity testing, and surface hardening (where applicable) to ensure seamless integration with Sulzer BBS 200-400 shafts, bearings, and bearing housings, extending shaft service life and maintaining pump operational stability.


Key Specifications

ItemDetails
Part Number1211-200400
Compatible Pump ModelSulzer BBS 200-400 (API 610 Centrifugal Pump)
Installation PositionBearing side of the pump shaft (mating with angular contact bearing set)
Design StandardAPI 610 (12th Edition)
FunctionShaft protection against wear/contamination, bearing positioning/alignment, load distribution
Dimensional ToleranceComplies with ISO 2768-m and DIN 40683 standards
Fit TypePrecision interference fit with pump shaft (ensures no slippage under load); clearance fit with bearing inner race
Surface FinishRa ≤ 0.6 μm (optimized for bearing seating and lubrication retention)
Concentricity≤ 0.015 mm (to ensure bearing alignment and reduce vibration)
Shoulder Perpendicularity≤ 0.01 mm (relative to sleeve axis, for precise bearing positioning)
LengthMatches Sulzer original design (optimized for bearing assembly spacing and oil seal fit)
Keyway CompatibilityMatches Sulzer BBS 200-400 shaft keyway dimensions (where applicable)

Material Options & Application Suitability

Select the optimal material based on operating temperature, load conditions, and lubricant compatibility—all materials are engineered to provide superior wear resistance, load-bearing capacity, and bearing compatibility:

MaterialOperating Temperature RangeKey PropertiesRecommended Applications
Bearing Steel (GCr15)-20°C to 180°C (-4°F to 356°F)High hardness (HRC 60-64 after heat treatment), excellent wear resistance, good toughnessGeneral industrial applications, mineral oil lubrication, standard load conditions
Stainless Steel 316L-50°C to 350°C (-58°F to 662°F)Superior corrosion resistance, moderate hardness (HRC 25-30), compatible with synthetic lubricantsCorrosive environments, seawater-related applications, chemical processing
Duplex Steel 2205-40°C to 315°C (-40°F to 600°F)High strength (yield ≥450MPa), balanced corrosion/wear resistance, good fatigue resistanceOil & gas production, desalination, high-load corrosive environments
Inconel 625-20°C to 550°C (-4°F to 1022°F)Exceptional high-temperature stability, oxidation resistance, high creep strengthHigh-temperature steam, petrochemical refining, extreme thermal cycling conditions
Carburized Carbon Steel (20CrMnTi)-30°C to 200°C (-22°F to 392°F)Surface hardness (HRC 58-62) + core toughness, excellent wear resistance under loadHeavy-duty industrial pumps, high-speed operation, high axial/radial load conditions

*Material certification available upon request (including mill test reports, EN 10204 3.1/B; heat treatment certificates for hardened materials).*


Replacement Guidelines & Installation Best Practices

When to Replace

  • Surface wear, scoring, or pitting on the bearing mating area (depth >0.2mm)

  • Sleeve deformation or shoulder damage (affecting bearing positioning)

  • Bearing failure related to sleeve misalignment or wear (e.g., bearing inner race damage)

  • Shaft runout increase (≥0.05mm at bearing location)

  • Bearing replacement (recommended to inspect and replace sleeve synchronously)

  • Proactive replacement for critical applications every 3-4 years (or 8,000 operating hours)

Installation & Maintenance Precautions

Pre-Installation Inspection

  1. Verify part number, material, and dimensional fit with Sulzer BBS 200-400 pump shaft (reference pump maintenance manual).

  2. Check for transportation damage (chips, cracks) and ensure bearing mating surface/shoulder is smooth (no burrs, scratches, or corrosion).

  3. Measure sleeve inner diameter and shaft outer diameter to confirm interference fit tolerance (-0.01 to -0.03mm, per Sulzer design).

  4. Confirm surface finish (Ra ≤ 0.6 μm) and shoulder perpendicularity with a precision gauge.

Installation Process

  1. Thoroughly clean the pump shaft and sleeve inner bore—remove rust, debris, or old anti-seize compound.

  2. Heat the sleeve to 100-120°C (212-248°F) using an oven or heat gun (avoid open flame) to expand the inner diameter; ensure uniform heating to prevent deformation.

  3. Align the sleeve keyway (if applicable) with the shaft key, then slide the sleeve onto the bearing side until fully seated against the shaft shoulder—use a soft hammer or press tool for gentle seating (avoid forceful impact).

  4. Allow the sleeve to cool to ambient temperature (typically 30-60 minutes) to achieve a tight interference fit with the shaft.

  5. Deburr the sleeve edges and apply a thin layer of compatible lubricant to the bearing mating surface.

Post-Installation Validation

  1. Measure runout at the bearing mating surface (≤0.03mm) using a dial indicator to ensure concentricity.

  2. Verify shoulder perpendicularity (≤0.01mm) to confirm precise bearing positioning.

  3. Install the angular contact bearing set and oil seal per manufacturer's instructions; ensure bearing inner race fits snugly on the sleeve without play.


Why Choose HYRIG's 1211-200400 Shaft Sleeve (Bearing Side)?

  • Bearing-Perfect Fit: CNC-machined to match Sulzer BBS 200-400's original shaft and bearing dimensions—no modifications required for seamless assembly.

  • Dual Function Design: Protects the pump shaft from wear and contamination while ensuring precise bearing positioning and load distribution, reducing bearing failure risk.

  • Load & Wear Resistant: Optimized material selection (including hardened options) to withstand high axial/radial loads and long-term bearing friction.

  • Direct Replacement: Meets or exceeds Sulzer original specifications for dimensional accuracy, concentricity, and API 610 compliance.

  • Quality Assurance: 12-month warranty against material defects and manufacturing errors; technical support for fit verification and installation guidance.


Order & Inquire

For pricing, material availability, lead time, or custom material requests (e.g., high-temperature or high-load optimization), contact HYRIG's technical sales team:

Email: info@hyrig.com

Please provide your pump's serial number, operating conditions (temperature, pressure, load characteristics), and bearing model for personalized recommendations and a detailed quote.


Note: HYRIG's 1211-200400 shaft sleeve (bearing side) is a drop-in alternative to Sulzer original parts, designed to meet or exceed API 610 performance and reliability standards. All units are packaged in protective materials to prevent surface damage during transit.


Name:
Message:
Verification code:
Submit
Comment