VS6 Pump Technical Specifications – API 610 Vertical Inline Single‑Stage Process Pump for Pipeline Installation

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
VS6 pump API 610 vertical inline single-stage process pump technical specifications. Performance: flow 5–1200 m³/h, head 10–250 m, speed 1480/2980 rpm, temperature -40°C to 350°C, max pressure 25 bar, optimized low NPSH. Structure: vertical inline (VS6), inline flanged straight through pipeline connection, foot or centerline mounting, closed single suction impeller, vertical inline volute radial split casing, heavy-duty oil lubricated bearings, API 682 cartridge mechanical seal. Materials: cast iron/carbon steel/316L/duplex casing; 304/316L/duplex/high chrome impeller; forged alloy/stainless steel shaft; replaceable anti-corrosion wear parts. Documents: API data sheet, inline installation drawing, performance curve, 3D model, material certificate.

Conatct For Details
DetailReview(0)Additional

This page provides complete technical parameters for our VS6 API 610 vertical inline single‑stage centrifugal process pump. The VS6 features an inline flange design that allows straight‑through pipeline installation without direction changes, saving floor space and reducing piping costs. Its compact vertical structure, back pull‑out maintenance, and wide material range make it ideal for refinery utility systems, petrochemical circulation, chemical plant transfer, and heating/cooling loops.


Performance Range

ParameterValue
Flow rate5 ~ 1,200 m³/h (22 ~ 5,280 GPM)
Total head10 ~ 250 m (33 ~ 820 ft) – higher on request
Speed1,480 / 2,980 rpm (50/60 Hz)
Medium temperature-40°C ~ +350°C (-40°F ~ +662°F) – higher with centerline mount
Maximum working pressureUp to 25 bar (360 psi) – higher on request
NPSHrOptimized low NPSH hydraulic design (inducer optional)

Structural & Mechanical Design

  • Type: Vertical inline single‑stage process pump (API 610 VS6 designation)

  • Connection: Inline flanged, straight through pipeline – suction and discharge flanges are coaxial, allowing the pump to be installed directly into a pipeline without elbows or direction changes

  • Mounting: Foot mounted (standard for general service ≤200°C) or centerline mounted (optional for high temperature >200°C, eliminates thermal misalignment)

  • Impeller: Closed single suction design – high efficiency, good for clean or slightly contaminated liquids

  • Casing: Vertical inline volute, radial split – smooth flow path, easy maintenance access

  • Bearings: Heavy‑duty oil lubricated bearing housing (splash or forced feed) – designed for continuous operation

  • Seal: API 682 cartridge mechanical seal – supports all plans (11, 21, 23, 31, 52, 53, 54, etc.)


Material Options

ComponentStandard MaterialsUpgrade Options
CasingCast iron, carbon steel (WCB), 316LDuplex, super duplex
Impeller304, 316L stainless steelDuplex, high chrome alloy, bronze
ShaftForged alloy steel (4140), stainless steel (316L)Duplex, K500
Wear partsReplaceable anti‑corrosion alloyColmonoy‑coated, Stellite

Key Design Features Explained

Inline Flange Design
The pump casing has suction and discharge flanges on the same axis. It installs directly into a pipeline like a valve or fitting – no baseplate, no foundation elbows, no piping direction changes. This reduces installation cost and saves valuable floor space (footprint is essentially the pipe diameter).

Back Pull‑Out Maintenance
The entire rotating assembly (impeller, shaft, bearing housing, mechanical seal) can be removed from the top or rear without disconnecting the pipeline flanges. Maintenance downtime is reduced to hours, not days.

Foot or Centerline Mounting

  • Foot mounted: For general service up to 200°C. Simpler, lower cost.

  • Centerline mounted: For high temperature service up to 350°C+. Casing feet at shaft centerline prevent thermal misalignment.

Compact Vertical Structure
The motor sits on top of the pump, which sits directly in the pipeline. No separate baseplate, no large concrete foundation. Ideal for retrofits, skid‑mounted systems, and space‑limited pump houses.

API 682 Mechanical Seal
Accepts all API 682 seal types. For hydrocarbon or corrosive service, dual seals (Plan 52 or 53) provide zero leakage.


Typical Applications

  • Process pipeline inline boosting

  • Refinery utility systems (cooling water, fire water, general service)

  • Petrochemical medium circulation (solvents, heat transfer fluids)

  • Chemical plant pipeline transfer between storage and process

  • Heating and cooling circulating systems (hot water, chilled water, glycol)

  • Tank farm pipeline pumping


Available Technical Documents (Free Request)

  • API 610 data sheet (filled with your operating conditions)

  • Inline installation drawing (2D CAD, PDF/DWG) – shows flange dimensions, overall height, bolt circle

  • Performance curve (head, efficiency, NPSHr vs flow)

  • 3D model (STEP/IGES for plant layout)

  • Material certificate (EN 10204 3.1 or 3.2)


Get Your VS6 Pump Technical Specification Package

To request a complete documentation package with a formal quotation, please send us your operating conditions:

  • Flow rate (m³/h or GPM)

  • Total head (m or ft)

  • Fluid name and temperature (°C)

  • Any special requirement (material, seal plan, centerline mount, low NPSH, ATEX, etc.)

Our engineering team will respond within 24 hours with:

  • Recommended VS6 pump model (size, impeller trim, mounting type)

  • Performance curve PDF

  • API 610 data sheet

  • Inline installation drawing (2D CAD) and 3D model link

  • Material and seal recommendations

  • Factory direct price (EXW / FOB / CIF)

Email: info@hyrig.com

We are a professional API 610 pump manufacturer (OH1–OH6, BB1–BB5, VS1–VS7 types) serving global refineries, petrochemical plants, chemical facilities, power utilities, and industrial pipeline systems. Contact us for custom‑engineered VS6 vertical inline pumps at factory direct wholesale pricing.


Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit