The idle shaft assembly is a vital transmission component in the ZQ127/25Y TEDA master tong, supporting the idler gears that transfer power between the hydraulic motor and the drive gear train. This assembly ensures smooth, efficient power transmission while maintaining correct gear alignment and backlash. Regular inspection and replacement of worn idle shaft components are essential to prevent gear damage and transmission noise.
Locating Disc (Item 1 – Purchase No. ZQ25-86, Part No. XYQ3C.Z-5, quantity 2): Two locating discs position the idler shafts axially within the transmission housing, preventing end‑float and ensuring correct gear mesh alignment. They act as thrust surfaces for the idler assemblies. Inspect for wear on the contact faces – replace if worn.
Idler Shaft (Item 2 – Purchase No. ZQ25-80, Part No. ZQ25.1.3-4, quantity 2): Two precision‑ground idler shafts support the idler gears within the transmission housing. These shafts are subjected to high shear and bending loads during torque transmission. Each shaft must be straight and free from scoring. Inspect shaft journals for wear and replace if out of tolerance.
Seal Ring (1) (Item 3 – Purchase No. ZQ25-76, Part No. ZQ25.1.3-2, quantity 4): Four seal rings provide dynamic sealing that prevents lubricating grease from escaping the bearing cavity while keeping contaminants out. These are critical for maintaining proper lubrication. Always replace seal rings during any overhaul – never reuse them.
O-ring 63×5.7 (Item 4 – Purchase No. ZQ25-77, Part No. GB1235-76, quantity 4): Four O‑rings provide static sealing between the shaft sleeve and the housing. They prevent lubricant leakage and maintain a clean bearing environment. Replace during every major overhaul.
Idler (1) (Item 5 – Purchase No. ZQ25-75, Part No. ZQ25.1.3-1, quantity 2): Two idler gears that mesh between the drive gear and the open gear of the tong head. They transmit power while providing speed reduction. Gear teeth should be inspected for pitting, wear, or chipping – replace idle gears as matched pairs to ensure even tooth contact.
Roller Φ10×30 (Item 6 – Purchase No. ZQ25-78, quantity 40): Forty cylindrical rollers measuring 10mm diameter by 30mm length. These rollers are the bearing elements that support the idlers on the idler shafts. They reduce friction and allow smooth rotation under load. Rollers must be inspected for flat spots, scoring, or diameter reduction; replace all rollers in a set when servicing to maintain even load distribution.
Shaft Sleeve (1) (Item 7 – Purchase No. ZQ25-79, Part No. ZQ25.1.3-3, quantity 2): Two shaft sleeves provide wear‑resistant bearing surfaces between the idler and the shaft. They protect the shaft from direct contact with the rotating idler and are designed as consumable items. Replace sleeves when they show wear or when replacing rollers.
Idle Shaft Assembly Operation
The idler shafts (Item 2) support the idlers (Item 5) within the transmission housing.
Locating discs (Item 1) position the shafts axially, preventing end‑float.
Rollers (Item 6) and shaft sleeves (Item 7) provide bearing surfaces for smooth rotation.
Seal rings (Item 3) and O‑rings (Item 4) retain lubrication and prevent contamination.
The idlers transmit power between the drive gear and the open gear.
Maintenance and Inspection Points
Disassemble carefully – keep rollers organized, maintaining the grouping of 40 rollers per idler shaft.
Clean thoroughly with diesel fuel or solvent to remove old grease and debris. Inspect for metallic particles that indicate advanced wear elsewhere.
Measure shaft journals with a micrometer to check the idler shaft for wear. Replace if journals show measurable reduction from original dimensions.
Inspect gear teeth on both idlers for wear patterns. Uneven wear may indicate misalignment or damaged bearings.
Replace seal rings and O‑rings to ensure contamination protection and proper lubrication retention.
Apply high‑quality grease to rollers, shaft sleeves, and bearing surfaces during assembly.
Check axial play after assembly – verify that idler shafts have minimal end‑float (within specification). Adjust using locating discs if necessary.
Reassembly Sequence
Press the shaft sleeves (Item 7) onto the idler shafts (Item 2).
Place the O‑rings (Item 4) into the housing grooves.
Install the rollers (Item 6 – 40 per idler) around the shaft, ensuring even spacing.
Slide the idler (Item 5) over the roller set.
Install the seal rings (Item 3) to retain grease.
Insert the complete assembly into the housing, ensuring the locating discs (Item 1) are correctly positioned.
Rotate the idler by hand to confirm smooth, binding‑free rotation.
Ordering and Replacement Guidance
When ordering components for the idle shaft assembly, always reference both the Purchase No. and Part No. to ensure correct specification. The idlers (ZQ25-75) and idler shafts (ZQ25-80) are the primary working components. All rollers (ZQ25-78) should be replaced as a set. Seal rings (ZQ25-76) and O‑rings (ZQ25-77) should be replaced during every major overhaul.
For assistance with part identification, assembly guidance, or to place an order for any ZQ127/25Y TEDA idle shaft assembly component, please contact us via email at info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.