The power input shaft assembly is the primary drive entry point of the ZQ127/25Y TEDA master tong transmission, receiving rotational power from the hydraulic motor and transferring it through the dual‑speed gear system. This assembly incorporates the clutch mechanism, multiple gear stages, bearings, and shafts that enable the two‑speed gear selection capability of the tong. As one of the most heavily loaded assemblies, regular inspection and timely replacement of worn components are essential.
Power Input Shaft (Item 1 – Purchase No. ZQ25-88, Part No. ZQ25.1.5-1, quantity 1): The power input shaft is the primary shaft that connects to the hydraulic motor coupling. It receives rotational power and transfers it into the transmission. The shaft features bearing journals and keyways for component mounting. Inspect for scoring, wear, or bending – any damage affects the entire transmission.
Deep Groove Ball Bearing 112 (Item 2 – Purchase No. ZQ25-89, Part No. GB276, quantity 1): A deep groove ball bearing supporting the power input shaft at the motor end. Check for roughness, noise, or play – replace immediately if worn.
Duplex Gear (2) (Item 3 – Purchase No. ZQ25-92, Part No. ZQ25.1.5-3, quantity 1): A two‑stage gear that provides the first stage of speed reduction in the transmission. It meshes with the clutch gear and shifting gear to transfer power. Inspect both gear stages for wear, pitting, or chipping – replace if damaged.
Thin Flat Key 28×10×63 (Item 4 – Purchase No. ZQ25-91, Part No. GB1567, quantity 4): Four thin flat keys that secure gears to the power input shaft, preventing relative rotation while allowing axial sliding for gear shifting. Keys must be inspected for wear or shearing. Always use new keys during reassembly.
Clutch Gear (Item 5 – Purchase No. ZQ25-90, Part No. ZQ25.1.5-2, quantity 1): The clutch gear engages with the duplex gear to transmit power from the input shaft. It is designed for sliding engagement to enable gear shifting. Gear teeth should be inspected for wear, chipping, or pitting.
Inner Gear Sleeve (Item 6 – Purchase No. ZQ25-94, Part No. ZQ25.1.5-5, quantity 1): A sleeve with internal teeth that engages with the clutch gear and shifting gear. Provides smooth torque transfer and alignment. Inspect internal teeth for wear.
Inner Spline Gear (Item 7 – Purchase No. ZQ25-93, Part No. ZQ25.1.5-4, quantity 1): A component with internal splines that transfers torque to downstream components. Inspect splines for wear or deformation – replace if damaged.
Shifting Gear (Item 8 – Purchase No. ZQ25-95, Part No. ZQ25.1.5-6, quantity 1): The shifting gear slides axially to engage the correct gear stage for high or low speed. It is actuated by the shift mechanism assembly and moves along the input shaft. The shifting gear must slide freely without binding. Inspect both the gear teeth and the sliding surfaces for wear.
Seal Ring (2) (Item 9 – Purchase No. ZQ25-96, Part No. ZQ25.1.5-7, quantity 1): A seal ring providing dynamic sealing for the rotating shaft. Prevents lubricating grease from escaping and keeps contaminants out. Always replace seals during overhaul.
O-ring 80×3.1 (Item 10 – Purchase No. ZQ25-99, Part No. GB1235, quantity 1): An O‑ring providing static sealing between housing components. Replace during every major overhaul.
Deep Groove Ball Bearing 207 (Item 11 – Purchase No. ZQ25-98, Part No. GB276, quantity 1): A deep groove ball bearing supporting the power input shaft at the transmission end. Check for roughness, noise, or play – replace if worn.
Bearing Cover (Item 12 – Purchase No. ZQ25-100, Part No. ZQ25.1.5-8, quantity 1): A cover that encloses and protects the bearing assembly. It is secured to the housing and contains the seal arrangement. Inspect for cracks and ensure the sealing surface is smooth.
Roller Φ10×30 (Item 13 – Purchase No. ZQ25-78, quantity 68): Sixty-eight cylindrical rollers that provide bearing surfaces within the power input shaft assembly. They support rotating components and reduce friction. Inspect for flat spots, scoring, or diameter reduction – replace all rollers as a set during servicing.
O-ring 40×3.1 (Item 14 – Purchase No. ZQ25-97, Part No. GB1235, quantity 1): An O‑ring providing additional static sealing within the assembly. Replace during every major overhaul.
Power Input Shaft Assembly Operation
The hydraulic motor drives the power input shaft (Item 1).
Power flows through the duplex gear (2) (Item 3) for initial speed reduction.
The clutch gear (Item 5) and shifting gear (Item 8) select the gear ratio.
The inner gear sleeve (Item 6) and inner spline gear (Item 7) transmit power.
Bearings (Items 2 and 11) support the shaft.
Rollers (Item 13) provide additional bearing surfaces.
The bearing cover (Item 12) and seals (Items 9 and 10) protect internal components.
Maintenance and Inspection Points
Disassemble systematically – keep all components organized.
Clean thoroughly – remove all old grease and debris from shafts, gears, and bearings using diesel fuel or solvent.
Inspect the power input shaft for wear, scoring, or bending – measure journal diameters with a micrometer.
Check gear teeth on the duplex gear, clutch gear, and shifting gear for wear patterns, pitting, or chipped teeth.
Test bearings by rotating by hand – check for roughness or noise.
Inspect all rollers for flat spots or damage – replace as a set.
Check splines on the inner spline gear for wear.
Replace seals and O‑rings to prevent leakage and contamination.
Lubricate during assembly – apply high‑quality grease to all bearing surfaces, gears, and rollers.
Verify smooth rotation after assembly.
Ordering and Replacement Guidance
When ordering components for the power input shaft assembly, always reference both the Purchase No. and Part No. to ensure correct specification. Bearings (ZQ25-89, ZQ25-98) are critical precision components – use only genuine parts. The power input shaft (ZQ25-88) should be inspected for straightness. All rollers (ZQ25-78) should be replaced as a set. Seals and O‑rings (Items 9, 10, 14) should be replaced during every major overhaul.
For assistance with part identification, assembly guidance, or to place an order for any ZQ127/25Y TEDA power input shaft assembly component, please contact us via email at info@hyrig.com.
total 0 Sheet,Only 5 images can be uploaded, each less than 5m.