ZQ168-50 Power Tong Parts | Jaw, Gearbox & Hydraulic Replacement Parts

2026-11-21 17:46

Key Facts

  • Replacement parts for ZQ168-50 hydraulic power tong.
  • Organized by system, not by guessed part number.
  • Covers wear components, replacement assemblies, and maintenance kits.
  • Confirm fitment by tong model, installed position, photo, and key dimensions.
  • Compatible host models include ZQ168-50, ZQ168/50II, and ZQ168/50IIA.

Key Specifications

Host parameterZQ168-50
Max torque, low gear50,000 N.m
High gear speed at 120 L/min60 rpm
Low gear speed at 120 L/min4.1 rpm
Hydraulic rated pressure16.6 MPa
Hydraulic rated flow120 L/min
Drill pipe range2-3/8 in to 6-3/8 in
Casing range4-1/2 in to 5-1/2 in
Tubing range3-1/2 in to 4-1/2 in

Source: ZQ168-50 technical data. Part-level P/Ns are not specified in the source document; confirm with supplier before ordering.

Part Coverage by System

SystemTypical replacement partsPart number status
Gripping systemJaw assemblies, jaw racks, dies and inserts, rollers, die seatsP/N not specified; confirm with supplier
Gearbox and transmissionOpen gears, pinions, shafts, bearingsP/N not specified; confirm with supplier
Hydraulic drive and controlHydraulic motor, directional valve, relief valve, seal kitsP/N not specified; confirm with supplier
Brake systemBrake band, friction platesP/N not specified; confirm with supplier
Backup tongJaws, dies, pins, linkage componentsP/N not specified; confirm with supplier

Compatible Host Models

  • ZQ168-50 hydraulic power tong.
  • ZQ168/50II and ZQ168/50IIA variants with the same core performance but different dimensions and configuration.
  • ZQ162/50 may share selected components; confirm fitment by installed position and dimensions before order.

Cross-Reference & Replacement

Replacing a worn component starts with matching the installed configuration, not only the tong model. Check these points before ordering:

  1. Tong nameplate model and variant.
  2. Installed position and a clear photo of the worn part.
  3. Key dimensions such as jaw width, roller OD, seal cross-section, and mounting hole pattern.
  4. Hydraulic circuit pressure and flow data.

HYRIG can review photos and dimensions to match the correct replacement part or maintenance kit. Do not order by model number alone when the part-level P/N is unavailable.

Selection Support

Not sure which jaw die, seal kit, or hydraulic component fits your ZQ168-50? Send the tong model, a photo of the installed part, and key dimensions. HYRIG will confirm the correct replacement by system and configuration before quotation.

Applications

These replacement parts are intended for ZQ168-50, ZQ168/50II, and ZQ168/50IIA hydraulic power tongs used in offshore and onshore drilling and workover operations. Confirm the exact host model and installed position before ordering.

Safety note: Hydraulic power tongs operate at high pressure. Selection, installation, and maintenance must be performed by qualified personnel in accordance with applicable safety standards and the manufacturer operating instructions.

Frequently Asked Questions

Q: Can I order ZQ168-50 parts by part number?

A: Part-level P/Ns are not uniformly listed in the public catalog. Provide the tong model, installed position photo, and key dimensions so HYRIG can match the component by system.

Q: Are ZQ162/50 parts interchangeable with ZQ168-50?

A: Selected components may be interchangeable, but fitment must be confirmed by installed position, dimensions, and configuration. Do not assume full interchangeability.

Q: Do you supply complete assemblies and individual wear components?

A: HYRIG supplies replacement assemblies, wear components, and maintenance kits. Confirm the required scope before order.

Contact

For ZQ168-50 power tong replacement parts, contact HYRIG: info@hyrig.com

Name:
Message:
Verification code:
Submit
Comment