4" CTX Desilter Cone | Brandt 26AW / 406-218-U Compatible

QR code
share
WeChat
Sina Weibo
QQ
QQ space
Douban
Baidu Post Bar
copy Link
Facebook
X
LinkedIn
Pinterest
Line
Tumblr
This 4-inch CTX desilter cone is a drop-in compatible replacement for the Brandt 26AW (Cone Assy, Hopper 4′) and the 406-218-U (4" CTX Complete Assembly). Each cone processes 50–65 GPM at 40–75 ft of head, removing solids in the 15–70 μm range on Brandt King Cobra and VSM 300 mud cleaners. The urethane cone body and grooved-end connection match the original hopper footprint, so existing manifold brackets and 2" Victaulic couplings require no alteration. HYRIG supplies independent, compatible replacement products for NOV Brandt desilter installations; we are not affiliated with, authorized by, or endorsed by NOV Brandt or National Oilwell Varco.
Conatct For Details
DetailReview(0)Additional

Key Facts



Replacement Part No.Brandt 26AW (Cone Assy) / 406-218-U (CTX Assembly)
ConfigurationSingle 4" urethane hydrocyclone, grooved-end inlet
Flow Capacity50–65 GPM per cone at 40–75 ft of head
Separation Range15–70 μm (API RP 13C tested)
Apex Nut26AO (adjusting nut for underflow control)
Body MaterialAbrasion-resistant urethane; ceramic insert available on request
Compatible HostKing Cobra / VSM 300 mud cleaners, Brandt SE-16 desilters
Replacement Compatibility26AW / 406-218-U; verify bushing (26AA) and apex nut (26AO) before order

Key Specifications (4" CTX Desilter Cone 26AW / 406-218-U Compatible)

ParameterValue
Nominal inner diameter4 in (102 mm)
ConstructionAbrasion-resistant urethane; ceramic insert molded into underflow available
Capacity per cone50–65 GPM at 40–75 ft of head
Separation range (mud)15–70 μm (API RP 13C)
D50 cut point (water)12–20 μm (for reference only; mud cut point governs selection)
Apex / underflow controlAdjusting nut 26AO; bushing 26AA
Manifold connection2" Victaulic grooved-end coupling (Style 77/78 seals rated for 75 ft head)
Compatible headerDSN-3H-10CTX (for 10" stage); 4" desilter hoppers on King Cobra / VSM 300
Wear life referenceUrethane body rated for extended service; inspect every 1,000 operating hours

Data source: Technical data table.

Dimensions

DimensionValue
Overall cone heightMatches 26AW / 406-218-U hopper outline
Cone body OD4 in (102 mm) nominal
Manifold interface2" Victaulic grooved-end; existing hopper accepts the replacement without bracket modification
Weight per cone (approx.)4–6 kg depending on ceramic vs. urethane configuration
Associated elbow2" grooved-end overflow elbow (verify against existing header)

Structure / Working Principle

Drilling mud enters the 4" CTX cone tangentially through the 2" grooved-end inlet. Centrifugal force drives silt-sized solids to the urethane wall and down through the underflow opening controlled by the adjusting nut (26AO), while clarified fluid exits upward through the vortex finder. The ceramic insert option molded into the underflow area resists abrasion far beyond standard polymeric material, which is why it is specified in high-sand formations where urethane alone erodes too quickly.

The adjusting nut (26AO) and bushing (26AA) are both field-replaceable without discarding the cone body. When the underflow spray becomes coarse, you can change the apex nut or swap the bushing to restore the original cut point—rather than replacing the entire 26AW / 406-218-U assembly. This modular wear-part logic keeps maintenance cost proportional to actual wear.

Cross-Reference & Replacement

Looking for a compatible replacement for a Brandt 4" CTX cone? Check these 4 points before ordering:

  1. 26AW vs. 406-218-U — 26AW is the Cone Assy listed for the standard Hopper 4′ desilter; 406-218-U is the CTX complete assembly part number used in the CTX-specific Parts List. Confirm which number is stamped on your existing cone or hopper before matching.
  2. Adjusting nut and bushing — the 26AO nut and 26AA bushing control the underflow opening. If your existing nut is seized or the bushing is grooved, order both with the cone to avoid a second shutdown.
  3. Ceramic vs. urethane underflow — standard urethane suits most water-base and oil-base muds; specify the ceramic insert if your feed sand content is high and the urethane underflow erodes within one maintenance cycle.
  4. Header coupling — the 4" CTX cone connects via a 2" Victaulic grooved-end coupling. Verify that your King Cobra / VSM 300 header uses the same Style 77/78 seal profile before installation.

Not interchangeable with: 10" CTX desander cones (106-200 series) or 4" cones designed for non-Victaulic flange manifolds, without verifying the header connection and inlet dimensions first. If your header uses a flanged rather than grooved connection, send us the header drawing before ordering.

Compatible Host Models

This 4" CTX desilter cone is intended for:

  • Brandt King Cobra and King Cobra Hybrid mud cleaner desilter sections (hopper 4′ configuration)
  • Brandt VSM 300 mud cleaners with 4" desilter cones
  • Brandt SE-16 desilter units using 26AW / 406-218-U cone assemblies

For the 10" CTX desander counterpart used ahead of the desilter stage, see 10" CTX desander cone 106-200 compatible replacement. For the full NOV Brandt-compatible hydrocyclone range, see NOV Brandt-compatible hydrocyclones.

Applications

  • King Cobra / VSM 300 desilter stage — the 4" CTX cone removes 15–70 μm solids after the shaker and desander stages, protecting the centrifuge from fine-solids overload.
  • High-sand formations with ceramic underflow — the ceramic insert option extends service life in formations where standard urethane underflow erodes too quickly.
  • Weighted mud systems — the 26AO adjusting nut allows underflow tuning to balance fine-solids removal against barite loss.
  • Scheduled cone / nut / bushing replacement during shutdowns — replacing only the 26AO nut or 26AA bushing extends the service interval of the 26AW body without full-assembly cost.

Selection Support

Not sure whether your existing unit uses the 26AW hopper assembly or the 406-218-U CTX complete cone, or whether a ceramic underflow insert is worth the upgrade for your formation? Send us a photo of the cone body and the part number stamped on the adjusting nut (26AO) or bushing (26AA), and we will confirm the matching configuration before you order.

Spare Parts

HYRIG provides replacement wear components for the 4" CTX desilter cone. The following part-level items can be quoted separately against the 26AW / 406-218-U assembly:

Part NameReference Part No.Notes
Cone Assy (Hopper 4′)26AWComplete 4" cone assembly
4" CTX Complete Assembly406-218-UCTX-specific complete cone
Apex Nut, Adjusting26AOUnderflow control
Nozzle / Bushing26AAUnderflow wear part
Ceramic Insert (underflow)Verify against drawingOptional high-abrasion upgrade
2" Grooved-End ClampA349/14AManifold connection
2" Grooved-End ElbowA349/44JOverflow routing

Qty as per parts list; verify against original drawing. For wear-part inspection guidance and the full Brandt CTX parts index, see Brandt CTX hydrocyclone wear parts.

Frequently Asked Questions

Q1: Is this an original NOV Brandt product?
A: No. HYRIG supplies independent, compatible replacement products and is not affiliated with, authorized by, or endorsed by NOV Brandt or National Oilwell Varco.

Q2: How do I confirm whether I need 26AW or 406-218-U?
A: 26AW is the hopper 4′ cone assembly; 406-218-U is the CTX complete assembly. Match the number stamped on your existing cone or hopper.

Q3: Can I change the underflow opening without replacing the full cone?
A: Yes. The 26AO adjusting nut and 26AA bushing are field-replaceable. Confirm the nut and bushing condition before ordering.

Q4: What is the typical lead time for a 4" CTX desilter cone?
A: Standard urethane cones ship in 2–3 weeks. Ceramic underflow options may require 4–5 weeks. Plan around year-end shutdowns.

Q5: What should I inspect if the cone stops holding cut point?
A: Check the 26AO adjusting nut for thread wear and the 26AA bushing for grooving. A worn bushing or loose nut is the most common cause of coarse underflow on Brandt 4" cones.

Contact

For 4" CTX desilter cone selection and compatible replacement parts, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Existing part number (26AW hopper assembly or 406-218-U CTX assembly) or a photo of the cone body
  • Adjusting nut (26AO) and bushing (26AA) condition
  • Ceramic vs. standard urethane underflow preference
  • Required quantity and destination port
Comment

comment
Name
Praise degree
Message:
Upload pictures:
    total 0 Sheet,Only 5 images can be uploaded, each less than 5m.
    Verification code
    Submit