Brandt CTX Hydrocyclone Parts | Apex, Nut & Bushing

2026-11-07 22:17

Key Facts



Primary Wear Parts (4")Adjusting Nut (26AO), Bushing (26AA)
Primary Wear Parts (10")Apex (106-204), Adjusting Nut (106-205)
Modular Sections (10")Middle Section (106-208), Bottom Section (106-201)
Compatible Cones4" CTX (26AW / 406-218-U), 10" CTX (106-200)
MaterialUrethane standard; ceramic inserts available
Inspection CycleEvery 1,000 operating hours (typical)

Wear Parts by Configuration

4-inch CTX Desilter Cone (26AW / 406-218-U Compatible)

Part NameReference Part No.Function
Apex Nut, Adjusting26AOControls underflow opening; most common wear point
Nozzle / Bushing26AAUnderflow wear part; replace if grooved
Ceramic InsertVerify against drawingOptional upgrade for high-abrasion sand
2" Grooved-End ClampA349/14AManifold connection

10-inch CTX Desander Cone (106-200 Compatible)

Part NameReference Part No.Function
Apex, 1.25"106-204:4APPrimary underflow wear point
Nut, Adjusting106-205Retains the apex; replace if threads are stripped
Cone Middle Section106-208Replace only if deep grooving occurs
Cone Bottom Section106-201:4APReplace if the lower cone body erodes
Fluid Splitter106-207Internal header component (if applicable)

Data source: Technical data and parts list.

Wear Inspection Guidance (Symptoms & Actions)

A hydrocyclone's cut point drifts when the apex, nut, or bushing erodes. Instead of guessing a replacement date, monitor the underflow pattern.

  • Normal Operation: The underflow should discharge in a tight, cone-shaped spray (about 20–30°).
  • Worn Apex/Tip: The spray becomes coarse or rope-like. This means the opening has enlarged, letting finer solids bypass to the overflow.
  • Worn Nut/Bushing: Look for thread damage on the 26AO / 106-205 nuts, or visible grooves on the 26AA bushing. Severe wear changes the underflow control and disrupts the cut point.
  • Action: Shut off the individual cone's feed valve, remove the wear part, and inspect. Replace the nut, bushing, or apex if wear is visible.

Maintenance Tip: Inspect wear parts every 1,000 operating hours. In high-sand formations, check more frequently during year-end shutdowns to avoid unplanned downtime.

Cross-Reference & Replacement

Upgrading a worn wear part? Here's how to ensure a drop-in fit:

  1. Confirm the Cone Size: 4" cones use the 26AO nut and 26AA bushing; 10" cones use the 106-204 apex and 106-205 nut.
  2. Verify Threads and Grooves: Check that the adjusting nut threads or 2" Victaulic grooves are not cross-threaded or stripped before installing the new wear part.
  3. Select Material: Standard urethane suits most water-based and oil-based muds. For high-abrasive sand, consider ceramic inserts.

Not interchangeable with: Apexes or nuts designed for non-Brandt manifold patterns or different CTX generations without verifying thread diameter and pitch.

Compatible Host Models

These wear parts are compatible with:

  • Brandt King Cobra and King Cobra Hybrid mud cleaner desander and desilter sections
  • Brandt VSM 300 mud cleaners and DSN-3H-10CTX headers

To select a complete cone assembly, view the 4" CTX desilter cone 26AW compatible replacement or the 10" CTX desander cone 106-200 compatible replacement. For the full range overview, see NOV Brandt-compatible hydrocyclones.

Selection Support

Not sure whether your cone uses the 26AO nut or the 106-205 nut, or whether a ceramic insert is available for your specific wear part? Send us a photo of the current wear part and the cone body, and we will confirm the exact replacement part number before you order.

Frequently Asked Questions

Q1: Are these original NOV Brandt replacement parts?
A: No. HYRIG supplies independent, compatible wear parts and is not affiliated with or endorsed by NOV Brandt.

Q2: How do I know when to replace the adjusting nut or bushing?
A: Replace when the underflow spray becomes coarse or rope-like, or when threads/grooves are visibly worn, usually after 1,000 hours.

Q3: Can I replace just the 10" bottom section without buying a new cone body?
A: Yes. The 106-201:4AP bottom section and 106-208 middle section are designed for standalone replacement.

Q4: Do you offer ceramic wear parts for high-abrasive drilling?
A: Yes. Ceramic inserts are available for both 4" and 10" CTX cones to extend wear life in harsh formations.

Q5: What is the lead time for a replacement apex or nut?
A: Standard urethane wear parts ship in 1–2 weeks. Order before year-end shutdowns to avoid rig downtime.

Contact

For NOV Brandt-compatible hydrocyclone wear parts selection, contact HYRIG: info@hyrig.com

What to include for fastest quote:

  • Current part number or a photo of the worn part
  • Cone size (4" or 10")
  • Required quantity
  • Destination port
Name:
Message:
Verification code:
Submit
Comment